• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.277-283
• /
• 2020

In a concentric magnetic gear, which replaces the teeth of a mechanical gear with a permanent magnet, the polar ratio of the magnet that determines the reduction ratio affects the behavior of the magnetic gear dramatically. This study analyzed the density of transmission torque, the efficiency of torque considering the solid loss, and the torque quality, including the cogging characteristics using finite element analysis. When the pole number on the driving side was changed from two to five, it was confirmed that there was an optimal pole ratio, in which the transmission torque was maximized. Because eddy current generation density is proportional to the magnetic field, the transmission efficiency also shows a similar tendency to the transmission torque density, and the efficiency is more than 95% at a low gear ratio. The cogging characteristics due to the interaction of the permanent magnets with the limited number of poles are inversely proportional to the least common multiple between the number of magnets on the drive side and the number of modulator teeth. A test model was built for the transmission torque evaluation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.193-193
• /
• 2009

Thin-type 초음파모터의 구조는 크로스형태의 앓은 스테이터에 윗면과 아랫면에 각각 8개의 압전세라믹이 부착된 형태이고, 압전세라믹의 분극방향은 로터와 접촉하는 스테이터의 중심부인 네 개의 타점에서 순차적인 타원변위가 생성되도록 결정된다. 유한요소해석프로그램인 ATILA 5.2.4를 사용하여 형태, 길이, 두께, 스테이터 재질, 클램프특성이 최적 설계된 모델을 제작하였고, 푸쉬풀 게이지, x-y 스테이지, rpm 메터, 토크 게이지, 맨코더, AD컨버터를 이용하여 피드백 제어 구동시스템을 구성하였다. 그림 I은 마이크로컨트롤러 (ATmega)와 피드백회로를 이용한 구동 드라이버를 보여준다. 한 주기에서 1/4분주의 순차적인 네 개의 구형파를 생성하고, 이를 push-pull회로를 통하여 90도의 위상차가 나는 정현파를 생성하여 초음파 모터의 구동전원으로 사용한다. 피드백 회로인 엔코더와 AD 컨버터는 초음파모터의 속도를 피드백하여 정속도 운전을 위한 전압제어에 사용되었다. 특성 측정 결과, 제품화된 드라이버와 비교하여 큰 차이를 보이지 않았고 피드백 회로를 통하여 부하변화에 따른 속도의 극심한 변화를 0.2~0.4[N]의 범위에서 정속도 운전이 가능하였으며, 장시간의 운전에도 온도 및 속도특성이 안정적임을 확인하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.4
• /
• pp.649-657
• /
• 1992

Transmission error for a stepping motor-timing belt drive system is investigated experimentally and analytically. From FFT analysis of the experimental results, it is found that the transmission error consists of three periodic errors : (1) error by the stepping motor per one resolution angle theta.$_{m}$, (2) error by the pulley eccentricity per one revolution theta.$_{e}$, and (3) error by the meshing effect between the belt and the pulley teeth per one pitch revoltion theta.$_{p}$. In order to investigate the effects of some design parameters on the transmission error, the dynamic models of the stepping motor-timing belt drive system are derived by Bondgraph. According to the simulation results, as the belt total tension increases, theta.$_{m}$ and theta.$_{e}$ decrease due to the nonlinearity of the belt. In adition, the numerical and experimental results show that theta.$_{m}$ and theta.$_{e}$ of the loaded case are larger than those of the unloaded case. The analytical results are in good accordance with the experimental results.sults.s.sults.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.6
• /
• pp.608-615
• /
• 1999

In this paper, the compliance control method was propoSL'Cl and the phase-difference operating principle of an u ultrasonic motor described. The compliance control can he implementtcD with spring/damper properties of the r musculo-skeletal system of the actual limb in controlling its net configuration and movement. The proposed p phase-difference driving scheme is verifitcD through the computer simulation. Also, $textsc{k}$rformance of the proposed c control method of a two-link direct-drive manipulator are examinLD by the experimental results with resptc'Ct to s spring/ damper properties.

• Journal of Advanced Navigation Technology
• /
• v.27 no.2
• /
• pp.214-220
• /
• 2023

Because there exist a region in the rotational speed and torque map that the a particular combination of a motor and an ESC (Electronic Speed Control) can maintain its peak efficiency, identifying this region is important for designing an efficient system. Firstly the accuracy of the measurement device is verified using the published propeller measurement data. And then, the combined motor-ESC efficiencies of an individual propeller are measured at a wide range of rotational speeds. With measurements obtained from a large number of different propellers, efficiency contours are obtained. It is shown that there exist a significant difference between the measured combined efficiency and the motor efficiency computed using a simple model. In addition, with the same motor, the combined efficiency can have a meaningful variation depending on the model of the ESC. The efficiency contours derived from this study will be useful for the design and optimization of electric propulsion systems of an aircraft where propulsion efficiency is critical.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.106-114
• /
• 1998

Cogging torque is often a principal source of vibration and control difficulty in permanent magnet motors, especially at low speeds and loads. For example, reduction of cogging torque is an important specification for DC motors used for electric power stee- ring. This paper examines two motor design techniques, stator tooth notching and rotor pole skewing with magnet pole shaping, for reduction of cogging torque, and the effect of each method on the airgap flux, and the use of the Maxwell stress method and Fourier decomposition to calculate the periodic cogging torque. The analyses show that the cogging torque can be nearly eliminated by the suggested designs, with minimal scacrifice of output torque.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.181-186
• /
• 2002

Lately, as going on increasing in the demand of high power density(power/weight), it is necessary for hydraulic axial piston pump/motor to operate more high pressure and speed. But in these condition, there are some trouble like as friction loss. To reduce this friction loss, hydrostatic bearing is used far axial piston pump/motor frequently. In general, it is difficult to measure accurate friction torque of spherical hydrostatic bearing in the use of the existing devices. So, we have developed the measurement device using the reaction torque sensor to obtain the pure friction torque, fitted in the casing. In this report, we intend to make an introduction about this measurement device for friction torque of the spherical wear part and clarify the effect of friction characteristics on supply pressure and rotational speed with three types of pocket size by using this measurement device.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.5
• /
• pp.283-294
• /
• 2004

This paper introduces the new Direct Torque Control(DTC) method based on the estimated torque in Switched Reluctance Motor(SRM) and applies the proposed DTC to SRM for the instantaneous torque ripple reduction. The nonlinear characteristics of SRM is considered in the calculation of the estimated torque and the theory is described in this paper. Current control is one of the kernel elements of torque controller and the performance of the current control should be high for this work. But the conventional PI current control has a weak point in SRM application because of motional EMF. Consequently, this paper makes up for the weakness of PI controller through present of new current controller, that is termed the non-interference current control. The ability of proposed torque and current controller is verified through simulation and experiment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.3
• /
• pp.543-551
• /
• 2001

This paper is concerned with optimization of a motor torque to drive Parking Sign system. It needs to minimize powers for stand alone operation and requires the optimized parameters in order to move the plates in the minimum torque. The operation can be represented as a complicated non-linear equation which is difficult to solve by general optimization techniques. In this paper, the dynamic equations of the system are derived, also the suitable Genetic Algorithm is designed to solve the equations. Computer simulation shows the availability of this method.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.2561-2563
• /
• 2005

영구자석 매입형 동기전동기(IPM)의 전류제어는 표면부착형 동기전동기(SPM)보다 더 복잡하다. 그 이유는 전류에 대한 최대토크특성 때문이며 고성능 토크제어를 위해서는 d-전류와 q-전류를 독립적으로 제어를 할 수 있는 방법이 필요하다. 그러나 전류들간의 상태커플링 때문에 독립적으로 제어하기가 어려우므로 상태 디커플링이 필요하다. 상태디커플링은 인턱턴스에 의해 생기며 인턱턴스의 변화 때문에 상태디커플링이 쉽게 이루어지지 않는다. 그러므로 인턱턴스의 불확실성에 대처할 수 있는 디커플링 방법의 개발을 바탕으로한 전류들의 독립적인 제어가 필요하다. 본 논문은 슬라이딩 모드제어기법을 이용하여 디커플링할 수 있는 방법을 제안하기로 한다. 기본적인 제어방법은 PI제어이며 슬라이딩모드를 이용하여 PI제어의 성능을 향상시키는 접근방법으로도 생각할 수 있다.