교량의 주탑, 초고층빌딩과 같이 세장비가 큰 대형구조물의 경우 풍하중에 취약한 특성을 지니고 있어서 바람에 의해 직각 방향으로 발산 진동하는 갤로핑(galloping) 현상이 발생하게 된다. 구조물의 진동을 억제하려는 방안으로 단면 형상에 변화를 주어 공기역학적 불안정성을 감소시키는 방법이 사용되고 있다. 본 논문에서는 Edison_CFD를 이용하여 모서리 절단부의 비율과 받음각에 따른 공기력 특성에 대한 전산해석을 수행하였다.
반파장 길이를 가지는 일반적인 마이크로스트립 안테나는 작은 대역폭 특성을 가진다. 패치 안테나의 모서리를 적절하게 잘라내면 입력 임피던스가 변하여 이에 상응하는 광대역 특성을 얻을 수 있다. 본 논문에서는 2.4GHz ISM 대역에서 동작하는 광대역 마이크로스트립 패치 안테나를 대상으로 패치 안테나의 모서리 단면의 모양에 따른 입력 임피던스의 변화를 통하여 광대역 특성을 얻을 수 있도록 설계하였다.
The dimensional accuracy and global roughness between successive layers of VLM-s, which is a new rapid prototyping process using hotwire cutter and EPS foam, depend significantly on the operating parameters of hotwire cutter. In the present study, the effect of cutting angle on the kerf width and edge shape in hotwire cutting of EPS foam for the case of single-sloped cutting with one cutting angle was investigated. Through single-sloped cutting tests, the modified relationship between kerf width and effective heat input, considering the effect of the cutting angle, and the relationship between the melted area and the cutting angle were obtained. In order to investigate the effect of cutting angles on the thermal field in EPS foam, transient heat transfer analyses using single-sloped volumetric heat flux model and locally-conformed mesh were performed. Through the comparison between experimental and numerical results, it was shown that the proposed analysis model is needed to estimate the three-dimensional temperature distribution of the EPS foam for the case of single-sloped hotwire cutting.
레이저 절단가공에서 사용되는 보조가스의 충돌특성을 개선하기 위한 실험적 연구가 진행되었다. 보조가스의 압력, 노즐의 위치 및 각도 등 다양한 관계변수의 변화에 대하여, 초음속 사각노즐에서 분출되는 보조가스의 절단면 충돌특성이 기존의 원형노즐 경우와 비교 관찰되었다. 이를 위하여 쉴러린 유동가시화 및 절단면 하단에서의 피토압 측정이 진행되었다. 본 연구에서 응용된 사각노즐은 절단면 모서리에서 발생하는 마하디스크의 강도를 줄이고, 이를 통하여 기존의 원형노즐에 비하여 절단면을 따라 흐르는 보조가스의 박리현상을 약화시키고 보조가스 후방의 피토압력을 증가시킬 수 있음이 확인되었다.
The objective of this paper is to investigate the effects of the laser power, the material thickness, comer angles, and the loop size on the formation of the comer in the cutting of Inconel 718 super-alloy sheet using high-power CW Nd: YAG laser. In order to investigate the influence of comer angles and loop sizes on the melted area and the formation of comer in the sharp comer, angular cutting tests and loop cutting tests were carried out. The results of the angular cutting tests were shown that the melted area is minimized and the melting mode is changed from nose melting in the thickness direction to the secondary melting induced by the attached dross when the comer angle is $90^{\circ}$. Through the results of loop cutting tests, the variation of the melted area and the comer shape in the sharp comer according to the loop size were examined. In addition, it was shown that a proper loop size is approximately 3 mm. The results of above experiments will be reflected on the knowledge base to generate optimal cutting path of the laser.
(η6-mesitylene) manganese (Ⅰ) tricarbonyl hexafluorophosphate[MTH-Mn (Ⅰ)]과 황산 이메틸, 피로탄산 이에틸, 과망간산 칼륨 따위 화학탐침들을 사용하여 Pseudomonas alcaligenes 5S rRNA의 고차원 구조를 분석하였다. 5S rRNA의 삼차구조에서 MTH-Mn (Ⅰ)이 강하게 절단하는 자리들은 a고리의 $G_{12}AUGG_{16}$, b-C 구역의 3'쪽 가닥, 즉$G_{51}AAGUGAAGC_{60}$, B-a구역의 $U_{65}-AGCG_{69}$, d고리의 5'쪽 가닥의 $G_{72}AUGG_{76}$ 연속부분 들이다. MTH-Mn(Ⅰ)과 그밖의 화학 탐침들을 사용하여 얻은 절단 양식들에서 우리는, MTH-Mn(Ⅰ)으로 강하게 절단되는 연속부분들이 $tRNA^{Phe}$의 L자 구조의 모서리 부분에서와 같은 주머니 구조를 이룰 것이며, 이러한 구조를 형성할 때 b-C구역과 d고리가 돌쩌귀 구실을 하는 것으로 추정한다.
본 연구에서는 필렛엔드밀을 이용하여 복합곡면을 가공하기 위한 새로운 접근방법을 제안한다. 이 방법은 "곡선기반 접근방법"으로 기존의 "점기반 접근방법"에 비하여 몇 가지 특징들을 가지고 있다. 본 연구에서는 다면체로 표현된 곡면을 대상으로 하고 있는데, 볼록한 모서리와 꼭지점에서는 정확히 옵셋시키고 오목한 부위에서는 옵셋 곡면이 겹치는 것을 허용한다. 옵셋된 곡면을 절단 평면으로 자르고, 같은 평면상에 있는 교선 중에서 겹치는 부분의 윗 부분을 택하면 공구 간섭이 제거된 공구 경로를 얻게된다. 즉 계산이 복잡한 오목지역에서의 옵셋 시 발생되는 간섭을 2차원 평면상에서 제거함으로써 계산 과정을 단순화시키고 안정적으로 만든다. 본 연구에서 제안한 방법은 PC에서 VC++로 구현되었으며 몇 가지 적용 예를 보여 주고 있다.
The objective of present research works is to investigate the effects of process parameters, including the power of laser, cutting speed, material thickness, and the edge angle, on the melted area in the sharp edge of the cut material fur the case of cutting of a low carbon steel sheet using high-power CW Nd:YAG laser. In order to investigate the influence of edge angle and size of loop on the melted area in the sharp edge, angular cutting tests and loop cutting tests have been carried out. From the results of angular cutting tests, the relationship between the edge angle and the melted area has been obtained. The results of the experiments have been shown that the melted area is rapidly reduced from $120^{\circ}$ of the edge angle and the melted area is nearly zero at $150^{\circ}$ of the edge angle. Through the results of loop cutting experiments, the relationship between the cutting angle on the melted area in the edge according to the size of loop have been obtained. In addition, it has been shown that a proper size of loop is nearly 3 mm as the corner angle is greater than $90^{\circ}$ and 5 mm as the comer angle is less than $90^{\circ}$. The results of above experiments will be reflected on the knowledge base to generate optimal cutting path of the laser.
모서리-절단 사각형 패치를 격자 형태로 배열하고 순차 회전 기법을 이용하여 위성방송수신 대역에서 동작하는 LHCP 원형 편파 안테나를 설계한다. 삼각형 격자 현태의 순차 회전 기법을 사용한 안테나는 축비 대역폭, 교차 편파 특성등을 개선하는 효과가 있으며, 급전 선로에 의한 방사를 최소로 하여 방사 패턴에 미치는 영향을 줄일 수 있다. 설계된 안테나는 $\Phi$45$^{\circ}$평면에서 DBS 배열 안테나의 부엽 준위 규격(-27dB)과 교차 편파 준위(-20dB)를 만족하고 있다.
본 논문에서는 다구찌 기법을 사용하여 최적설계 한 중심 주파수가 920MHz인 휴대용 RFID 리더안테나를 제안한다. 제안한 안테나는 모서리가 절단되고 정사각형 마이크로스트립 패치에 네 변으로부터 슬롯을 갖는 구조이다. 이러한 슬롯구조는 마이크로스트립 패치안테나를 소형화 시킬 수 있으며, 슬롯이 없는 구조에 비해서 약 18%의 안테나 크기 감소가 가능함을 실험을 통해 확인 하였다. 슬롯의 구조를 갖게 되는 소형의 안테나는 복잡한 설계변수에 따라 변화하므로 최적의 안테나 설계를 위해서는 해석 및 시험단계에 수많은 반복이 요구된다. 본 연구에서는 해석 및 실험 횟수를 최소화할 수 있는 실험계획법인 다구찌법의 직교배열 표를 도입하여 설계할 때의 주요 요소들의 민감도 해석을 수행하고 그 영향성을 분석하여 해석결과를 바탕으로 설계반복을 최소화 하면서 최적의 구조를 갖는 안테나를 설계 하였으며 유전율이 4.4이고, 두께가 3.2mm 인 Epoxy 1.6T의 기판상에 제작한 안테나 특성에 대한 실험 결과를 제시하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.