• Journal of Korean Society of Steel Construction
• /
• v.29 no.5
• /
• pp.361-368
• /
• 2017

ASCE 7-10 defines the torsional irregular structure as the one that has large torsional responses caused by the eccentricity. The code requires that these structures should be designed abide by the torsional provisions. This study evaluates the influence of torsional provisions on the performance of the designed multiple steel moment frames with different eccentricity. In this study, 3D response history analyses are performed. The results show that the moment frame design according to the standard with torsional irregularity provisions showed larger performance as the eccentricity increased and the distribution of plastic hinges similarly to orthopedic structures.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.1
• /
• pp.13-18
• /
• 2015

Characteristics of restoring force for the wind-powered leisure boat was investigated using mathematical formulation and commercial computational method such as the ANSYS Workbench CFX-Mesh. The objective is to find the restoring moment and heel moment while boat is sailing in windy power. Conditions for angle of attack were given from $5^{\circ}$ to $90^{\circ}$. It is known that side force is larger in terms of angle of attack is higher, however critical angle is suggested to limit before over of $60^{\circ}$ for safe navigation for boat in wind. Natural results are found that stronger heel moment is observed when sail is used than no sail, and higher angle of attack is induced stronger heel moment.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.2
• /
• pp.172-178
• /
• 2015

The control moment gyroscope(CMG) which is well known as an effective high-torque-generating device is applicable to space vehicles, airplanes, ships, automobiles, robotics, etc. for attitude stabilization and maneuver. This paper deals with the overall details of 100Nm-class CMG development for various industrial applications, and provides the activities and results associated with the CMG system-level requirement analysis, the motor subsystem design/manufacturing/integration, the construction of ground support equipment, and the performance test and evaluation. The performance test reveals that the CMG generates the torque output more than 120Nm in as-designed operation of spin motor and gimbal motor.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.3C
• /
• pp.105-111
• /
• 2012

Bucket foundations, which are used in the foundations of offshore wind turbines, should be able to withstand large amounts of horizontal and moment loads. Tripod bucket foundation, which combines three single buckets, has been used to increase horizontal and moment capacities. This study performed numerical analysis using ABAQUS (2010), to analyze the group effect and the bearing capacity of a tripod bucket in clay. Parametric studies were performed varying the bucket spacing ratio S/D (S=spacing between the centers of the bucket and the tower; D=diameter of the bucket) and depth ratio L/D (L=embedded length of skirt). The applied constitutive models were a linear elastic perfectly plastic model with Tresca yield criteria for normally consolidated clay and an elastic model for buckets. Loading in the vertical, horizontal, and moment directions was simulated with an increase in each movement at a reference point. The bearing behavior and the capacities of a single and a tripod bucket were compared. Capacity evaluation method of the tripod bucket was suggested using the capacity of a single bucket.

• Journal of the Korean GEO-environmental Society
• /
• v.22 no.1
• /
• pp.5-12
• /
• 2021

Owing to economically efficient and easy installation, bucket foundation is a promising solution for offshore wind turbines. This paper aims at finding the behavior of suction caissons and soil surrounding the foundation by using three-dimensional finite element analysis. Under various loading conditions, a wide range of foundation geometries installed in dense and medium dense sandy soil was considered to evaluate ultimate horizontal load and overturning moment capacity. The results show that the rotation and displacement of the bucket due to monotonic loading are largely dependent on the foundation geometry, soil density and load eccentricity. Normalized diagrams and equations for the ultimate horizontal load and overturning moment capacities are presented that are useful tool for the preliminary design of such foundation type.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1A
• /
• pp.117-132
• /
• 2006

The existing analytical solutions for rectangular plates with three edges clamped and the other free are derived based on nondimensional differential equation and their characteristics are analyzed. Since Timoshenko and Woinowsky-Krieger's method (1959) can give solutions for the case limited to the aspect ratio of the plates less than one, this method are proved to be impractical for the bending moment calculation of the plates under consideration. Horii and Moto's method(1968) are modified by adding stabilizing terms to suppress overflow in the matrix computation, from which the series solution with maximum 150 terms can be obtained. By use of the series solution the convergence of computed bending moments is tested. The modified method can be shown to calculate the deflection properties for the plates with wide range of aspect ratios, but the computed x moment at the corner points formed by the free edge and the clamped edges can not satisfy the boundary condition and the cause of problem is discussed in detail.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.4A
• /
• pp.383-389
• /
• 2010

The concrete structural design provisions in Korea are based on ultimate strength design. Up to service load stage, it is assumed a linear stress-strain relation, but there is no stress-strain relationship for a concrete material from service load stage to limat state. According to the current provisions, an independent method is provided for the each calculation of deflection and crack width. In EC2 provisions based on limit state design, however, a stress-strain relationship of concrete is provided. Thereby, it is able to calculate a strength as well as a deflection directly from concrete stress-strain relationship. In this paper the moment-curvature relationship is directly calculated from a material law using equilibrium and compatibility conditions. Then strength and deflection are formulated. These results are compared with the values from the current provisions in Korea. From the results, the deflection based on a moment-curvature relationship is well agreed with experimental results and it is appeared that the deflection after the yielding of steel is also possible.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4C
• /
• pp.109-116
• /
• 2011

In this study, dynamic response of a vertical shaft subjected to seismic loads was evaluated by three-dimensional Finite Element (FE) approach. The emphasis was on quantifying the ground conditions, input motions and direction of motions. A series of parametric analyses were carried out. From the results of FE analysis, more than 1.7 times increase in shear force and bending moment is obtained when the stiff layer was thinker than the soft layer. And all of the maximum values were occurred near the interface between the soil layers. The dynamic behavior of vertical shaft was significantly influenced by the different frequencies of the input motion, and normalized acceleration of surrounding soil was 3 times larger than vertical shaft.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.2
• /
• pp.7-13
• /
• 2010

Stepped I-beams having increased moment of inertia at one end (singly stepped beam) or both ends (doubly stepped beams) can often be seen in construction of bridges due to material economy and easy fabrication of the section. This paper presents the results of the parametric study of lateral torsional buckling of monosymmetric stepped I-beams with constant depth subjected to uniform moment. Design recommendations were made based on the finite element results of the models having different combinations of monosymmetric ratio, stepped length ratio, flange thickness ratio and flange width ratio. The proposed approximation is acceptable based on the parameters given having mostly conservative results. The proposed equation can be further used to extend the study to different loading conditions.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.1
• /
• pp.43-55
• /
• 2001

본 논문에서는 현행 표준적인 P.S.C거더 교량의 적정 가로보 수를 위한 매개변수 연구를 수행하였다. 교량의 길이는 P.S.C거더교로서 국내에서 가장 흔히 사용되는 30m의 단순교를 채택하였다. 교량의 해석방법으로는 상부의 슬래브와 거더를 효율적으로 모델링하기 위하여 정밀해석법인 유한요소법을 사용하였다. 본 연구에서 사용된 매개변수로는 크게 두 가지로 분류되는데, 하나는 사용된 가로보의 개수이고 다른 하나는 교량의 사각(Skew)이다. 상부 슬래브는 쉘 요소와 빔 요소를 연결하는데 효율적인 회전자유도를 가지는 쉘 요소로 모델링 하였다. 슬래브와 거더의 중심축이 이격되어 있는 문제를 정확히 고려하기 위하여 편심보 요소를 사용하였다. 해석 모델은 가로보가 각각 7,5,3개 있는 경우를 선정하였다. 이러한 조건하에서 정적 해석을 수행하여 최대 휨모멘트, 전단력, 비틀림 모멘트값을 구하여 현행 시방서에서 규정된 극한치를 만족하는지 검토하였다. 검토결과 현재 사용되고 있는 P.S.C거더 교량에서의 가로보 개수는 과다한 것으로 판단되며 경제적인 설계를 위하여 가로보의 개수를 줄일 수 있을 것으로 제안하였다.