• 설비공학논문집
• /
• 제9권4호
• /
• pp.561-571
• /
• 1997

In this paper, the fundamental equations are developed for the pulsatile laminar flow generated by changing the oscillatory flow with $0{\leq}f{\leq}48Hz$ into a steady one with $0{\leq}Re{\leq}2500$ in a rigid circular pipe. Analytical solutions for the wave propagation factor k, the axial distributions of cross-sectional mean velocity $u_m$ and pressure p are schematically derived and confirmed experimentally. The axial distributions of centerline velocity and pressure were measured by using Pitot-static tubes and strain gauge type pressure transducers, respectively. The cross-sectional mean velocity was calculated from the centerline velocity by applying the parabolic distribution of the laminar flow and it was confirmed by using the ultrasonic flowmeter. It was found that the axial distributions of cross-sectional mean velocity and pressure agree well with theoretical ones and depend only on the Reynolds number Re and angular velocity $\omega$.

• 설비공학논문집
• /
• 제17권6호
• /
• pp.552-559
• /
• 2005

This paper describes an experimental study on the inertance pulse tube refrigerator using a small compressor. The purpose of this experimental study is to identify the performance of the inertance pulse tube refrigerator for various operating conditions and to obtain the optimum configuration. The dead volume effect is verified by two experimental apparatuses with different dead volumes between the compressor and the aftercooler. The refrigerator of the smaller dead volume shows better performance. The influence of operating frequency and charging pressure on the performance of the refrigerator is experimentally investigated. Reducing the regenerator mesh size improves the performance of the refrigerator. Finally, the inertance pulse tube refrigerator has maximum cooling capacity at the specific combination of the pulse tube length and the inertance tube length. The loss analysis is used to analyze and predict the optimum condition of the pulse tube refrigerator.

• 한국분무공학회지
• /
• 제27권3호
• /
• pp.134-143
• /
• 2022

When a recess is applied to a swirl coaxial injector that uses liquid and gas propellants, a self-pulsation phenomenon in which the spray oscillates at regular intervals may occur. The phenomenon is caused by the interaction between the liquid and gas propellants inside the injector recess region. The propellants' kinetic energies are expected to affect significantly the spray oscillation. Therefore, cold-flow tests using helium as a gas-simulating propellant were conducted and compared with the results of the previous study using air. Dynamic pressure was measured in the injector manifold and frequency characteristics were investigated through the fast Fourier transform analysis. In the experimental environment, the helium density was about seven times lower than the air density. Accordingly, the intensity of pressure fluctuations was confirmed to be greater when air was used. At the same kinetic energy condition, the perturbation frequency was almost identical in the low flow rate conditions. However, as the flow rate increased, the self-pulsation frequency was higher when helium was used.

• 유공압시스템학회논문집
• /
• 제3권2호
• /
• pp.21-26
• /
• 2006

With the increasing concerns on noise and vibration in hydraulic fluid power systems, it is important to find better way to reduce noise and vibration. In this study, the authors survey former researches on hose(viscoelastic tube) modeling in advance. And a summary of several existing methods for measuring the speed of sound in the fluid in pipes is presented. Their basic principles, advantages and limitations are compared. And The authors suggest a far simple identification procedure to obtain wave speed in hose by just using an experimental pressure data for the object tube with hose. In the new procedure, flow in hose is basically modeled by transfer matrix method, and wave speed in hose is obtained as data in frequency series. The wave speed in hose as data in frequency series will be used to compute the pressure pulsation attenuation in hydraulic pipe systems. The computed results are compared with the experimental ones, and the validity of the new procedure to obtain wave speed in hose is confirmed

• 전력전자학회논문지
• /
• 제7권3호
• /
• pp.297-302
• /
• 2002

유도전동기의 직접 토크 제어방식은 구조가 간단하여 구현이 용이하고, 빠른 토크 응답성을 갖는 것을 특징으로 견인용 유도전동기의 추동시스템 등에 그 응용분야를 넓혀가고 있다. 그러나 히스테리시스 제어기를 사용하여 출력전압을 결정하는 기존의 직접 토크 제어방식에서는 인버터의 스위칭 주파수가 히스테리시스 밴드 폭과 운전조건에 따라 가변하고 토크맥동이 발생하는 문제점이 있다. 따라서 본 논문에서는 인버터의 스위칭 주파수를 일정하게 유지하고 저속 및 고속 운전영역에서 전동기의 토크 및 고정자 전류 맥등을 저감하기 위한 목적으로 고정자 자속 제어개념과 공간전압벡터 P%에 의한 새로운 직접 토크 제어방식을 제안하였다. 시뮬레이션과 실험을 통해 제안한 알고리즘의 타당성을 입증하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2016년도 전력전자학술대회 논문집
• /
• pp.495-496
• /
• 2016

단상 계통연계형 인버터에서 전류센서를 통한 계통측 상전류 측정시 옵셋 오차는 전류센서와 측정 경로상에 위치한 아날로그 소자의 전압 불균형 및 비선형성으로 인하여 발생하게 된다. 옵셋 오차가 존재하지 않는 실제 상전류와 달리, 옵셋 오차를 포함한 측정된 전류로 전류 제어를 수행하게 되면 계통측상전류에 직류, 전원 주파수의 기본파 및 2배 고조파 성분을 야기한다. 이러한 직류 및 맥동 성분은 계통연계형 인버터의 전력전달에 있어서 효율을 저하시키는 원인이 된다. 본 논문에서는 단상 계통연계형 인버터에서 비례공진 전류 제어기를 적용하는 경우, 전류 옵셋 오차의 영향을 분석하고, 이를 저감하기 위한 알고리즘을 제안한다. 제안된 알고리즘의 타당성은 시뮬레이션과 실험을 통해 증명한다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.601-606
• /
• 2004

Vibration spectrums of the test loop according to flow conditions were analyzed in order to identify the sources of vibration at peak frequencies. While a flow condition of the sweep test was changed by varying pump rotational speed from 450 rpm to 1500 rpm by the step 150 rpm, midspan acceleration of the test section in width-direction and dynamic pressure perturbation in the test section were measured. Other sources of vibration due to the flow structure interactions, such as acoustic resonance, blade pulsing frequency and bellows wrinkles, were investigated. Pressure perturbation in the section and acoustic resonance due to branch pipe give major effects to the vibration of the test section in high frequency range of 1.5 kHz to 2.8 kHz.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.51-56
• /
• 2002

High pressure hose having tuning cables, called 'Resonator hose' is frequently used to attenuate pressure ripple generated by the pump for reducing the vehicle interior noise. A number of studies have been conducted on the resonator hose and its analytical models. However, there are few studies which deal with the influence of resonator hose on vehicle interior noise because the most of studies focused on transmission loss of the resonator hose. This paper presents NVH test results of power steering system and frequency analysis results. In the frequency analysis, both the relations between vibration, pressure ripple and vehicle interior noise and also the design parameters of high pressure hose influencing on vehicle interior noise were discussed. The test was done for various high pressure hose specimens in full turn condition.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1936-1941
• /
• 2003

Characteristics of the high frequency and pulsatile flow investigated experimentally to understand the flow phenomena in the hydraulic system. In the study, I axis fatigue tester which are widely used for automobile filed are selected. 4 Pressure transducer, amplifier, A/D convertor are used to analyse and to obtain the pulsatle pressure waveform with high frequencies in hydraulic system. Matlab are used. to analyse the characteristics of frequency. Variation of pump input pressure and actuator acceleration frequency, pressure wave are measured with or without accumulators. For with accumulator, frequency amplitude of pressure are very lower than those of without accumulator due to absorbing function of accumulator. As the actuator acceleration frequency increased, effect of accumulator are very important to decrease the pulsatile pressure waveform with high frequencies.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.591-595
• /
• 1997

In analysis of piping vibration of petrochemical plant, the forcing functions mainly depend upon the equipment working mechanism and vibration resources in the piping systems. In general, harmonic function is used for the system with rotary equipments. Mechanical driving frequencies, wave functions, and response spectrum are used for reciprocating compressors, surge vibration of long transfer piping, and seismic/wind vibration, respectively. In this study, for the spray injection case inside the pipe, forcing function was modeled, in which two different fluids are distributed uniformly. To confirm the results, the scheme used for the forcing function was applied for real piping system. The vibration mode of the real system was consistent with the 4th mode obtained by simulation using the forcing function formulated in this study.