• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.421-430
• /
• 1997

In this study, the static and the fatigue tests were performed with high tension bolted joints, of which the surfaces were spread with inorganic zinc-primer after shot-blast, and milling surface, and steel-natural surface, difference of friction surface condition were examined by comparing the esults of tests. From the result of synthetical investigation of this study. it is proper that using the torque management method in order to introduce design axial force to blots, and the provision of specifications that initial axial forces must be 110% of design axial forces is proper. Decreasing ratio of axial forces to initial force is proportional to common lorgarithms of time progress, it converge constant value after 20 hours, and decreasing ratio is little related to the roughness of friction surface. Sliding coefficient of milling, spreading inorganic zinc-primer, just producting is great in order and sliding forces are dependent on the applied axial forces, but if the applied axial forces are great, sliding coefficient become small by a loss of roughness. So it is confirmed that relation between the applied axial forces and the sliding forces are not proportional linearly. From the result of estimation on fatigue strength, all specimens satisfy the specifications with B-grade and milling surface is lower than the others about 14% in fatigue strength because in milling surface lose the function of friction-types joints at lower number of cycles. From the result of eximination for the distribution area of compressive force, friction area near to inside bolt is wider in the direction of stress than near to outside. It is guessed that this situation occurs because outside bolts firstly change from the friction connection to the bearing connection.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.9-19
• /
• 1997

In this paper, the modeling and analysis of dynamic characteristics has been carried out for friction clutches and brakes in an automatic transmission. From the operating oil pressure generated by the valve-body, time delay by check valve and the movement of piston has been examined. Also torque capacity and torque transferred at the clutch is studied. Heat capacity and temperature distribution at the reaction plate of clutch are codeled by time-dependent, nonhomogeneous partial differential equation, and brake torque, brake time, and the amount of heat generated are investigated. It is found that the time delay at the check valve is very short but dominant at the spool.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.760-761
• /
• 2015

기어는 회전 기계 사이의 동력 전달을 위한 장치이며 현재 산업 전반의 통상적인 기어는 기계적 기어가 주류로서 형성되어 있다. 하지만 기계적 기어는 맞물린 톱니바퀴의 물리적 접촉에 의해 접촉 경계면의 마모 및 파손, 소음과 진동의 문제가 있으며 유지보수 비용 또한 크다. 따라서 최근 물리적 접촉이 없어 기계적 기어의 많은 문제를 해결할 수 있는 마그네틱 기어 (Magnetic Gear)에 대한 관심이 높아지고 있다. 마그네틱 기어는 영구자석에서 생성된 자계를 이용하여 비접촉 동력전달이 가능하며, 마찰손실 제거, 유지보수의 용이성, 매우 적은 소음 및 진동 등의 장점을 가지고 있다. 본 논문에서는 이러한 마그네틱 기어의 토크전달 방법과 형상변화에 따른 전달토크 특성을 2-D 유한요소해석법을 이용하여 해석하고 분석하고자 한다.

• Journal of Aerospace System Engineering
• /
• v.12 no.1
• /
• pp.27-34
• /
• 2018

In this study, the generating of torque regarding the Control Moment Gyro (CMG) is proportional to the angular velocity of gimbal. This is the case because gimbal affects the attitude control of the satellite directly, and it is necessary to reduce the incidence of torque ripple of gimbal. In this paper, the cause of the torque ripple of gimbal is reviewed and mathematically modeled by assuming the friction imbalance of bearing, the magnetic field and the phase current imbalance of the motor. We are able to confidently estimate the modeling parameters of gimbal disturbance using a constant speed test, and then analyze the influence of applying feedforward control to our modeling. Additionally, the simulation results show that the torque ripple and angular velocity fluctuations are reduced when apply this modeling to the identified study parameters. Finally, we present the disturbance reduction technique using our disturbance modeling.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1738-1739
• /
• 2007

초음파 모터는 고정자와 회전자를 가압마찰하기 위해서 내부에 원형 판 스프링을 이용하고 있다. 출력 토크를 높이기 위해서 이러한 내부 스프링의 강도를 크게 하면 홀딩 토크 역시 커지게 된다. 이로 인하여 기동 시 많은 전류가 소모되며 일반적인 구동 파라미터에 따른 속도 특성 등 기존의 스프링 강도를 지닌 초음파모터(모델명 : 신생공업사(일) USR60-s1)의 특성과는 전혀 다른 특성을 보인다. 본 논문에서는 스프링이 강화된 새로운 타입의 초음파모터(모델명 : 신생공업사(일) USR60-s3)를 가지고 무부하 시의 속도 특성을 실험하였다. 이를 위해 FPGA를 이용해서 디지털 다중 초음파 모터 제어기를 설계하였고, 2상입력 전원의 주파수, 위상차, 주파수-위상차 다중 파라미터 등을 조절하면서 무부하 속도 특성을 측정하였다. 그 결과 홀딩토크가 강화된 초음파 모터의 경우 일반적인 기존 초음파 모터와 비교했을 때 전혀 다른 특성을 보이고, 위상차-주파수 다중 파라미터 조절방식이 조절방식임을 보인다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.2
• /
• pp.355-362
• /
• 2021

Since coaxial magnetic gears use non-contact power transmission, friction, wear, noise, and heat generated in the power transmission process of existing mechanical gears can be minimized. Currently, research for application to various industries is being actively conducted, but among the characteristics of coaxial magnetic gears, the problem of rapidly decreasing torque density at a high gear ratio was discussed. This paper proposes a direction for multiple gear combination using low gear ratio coaxial magnetic gears with high torque density. In order to confirm the effectiveness of the method, the torque density was compared with a single high gear ratio model, and the combination and design direction of multiple coaxial magnetic gears were shown.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.1
• /
• pp.53-61
• /
• 1997

The performance characteristics of magnetic fluid seals are studied numerically as a function of working gap, pole width, angle of pole sharpening, and shaft speed. The temperature distribution of a magnetic fluid seal with multiple tooth is investigated as a function of the contact fraction of magnetic fluids at the periphery of pole tooth using a finite element method. The most significant design parameter of a magnetic fluid seal is the working gap between the pole pieces and the rotating shaft. The result shows that with increasing the working gap, the friction torque decreases radically. The practical working gap for the pole pieces with triangular tooth zone profile is 0.2-0.4mm. The FEM results indicate that the optimal filling of a magnetic fluid between the pole pieces and the shaft is very important due to the accumulations of nonuniform friction heating within the pole pieces, which may interfere the magnetic circuit flow.

• Journal of the Korean Vacuum Society
• /
• v.10 no.2
• /
• pp.155-163
• /
• 2001

A number of screws are inevitably used for tightening flanges in constructing a vacuum system. A theoretical relation between the axial force and the torque exerted on a screw is easily obtained assuming that the friction force generated on the contacting plane is known, however, in practice the friction is influenced strongly by unknown detailed surface condition. It is difficult to tighten optimally and uniformly the flange seals if the screws commercially available have undefined surface conditions and scattered dimensions, and the axial force produced by the screws can not be expected properly. In this paper a scatter of the axial force over screws and the deviation from an expected one, depending on various fastening conditions, are investigated using a variety of M8, the most popular size for vacuum flanges, domestic stainless screws of hexagonal head and standard thread.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.173-180
• /
• 2004

The tread pattern of a tire has an important effect on tire performances such as handling, wear, noise, hydroplaning and so on. However, a finite element analysis of a patterned tire with detailed tread blocks has been limited owing to the complexity of making meshes for tread blocks and the huge computation time. The computation time has been shortened due to the advance in the computer technology. The modeling of tread blocks usually requires creating a solid model using a CAD software. Therefore it is a very complicated and time-consuming job to generate meshes of a patterned tire using a CAD model. A new efficient and convenient method for generating meshes of a patterned tire has been developed. In this method, 3-D meshes of tread pattern are created by mapping 2-D meshes of tread geometry onto 3-D tread surfaces and extruding them through tread depth. Then, the tread pattern meshes are assembled with the tire body meshes by the tie contact constraint. Residual aligning torque and frictional energy are calculated by using a patterned tire model and compared to the experimental results. It is shown that the calculated results of a patterned tire model are in a good agreement with the experimental ones.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.11
• /
• pp.67-73
• /
• 2001

This paper aims at developing a torque model for the high-speed tapping with small-diameter taps. As recent industries such as automobile and information technology grows, taps smaller than 5mm in diameter are needed much more. In that occasion, the friction force between a tap surface and a workpiece plays much more important role in the tapping torque than in he larger tapping. Tapping mechanism was analysed based on the tap geometry. It has two steps : one is a forward cutting composed of the chamfered threading and full threading and the other is the backward cutting. The torque by the cutting force in the chamfered threading is calculated using the cutting area and the specific cutting force while the torque by the friction force, which is rather dominant than the cutting force both in the full threading and in the backward cutting, is calculated using the normal force on the threads and the friction coefficient. The experiment has shown that the results by the proposed torque model fit quite well with the acutal measurements within the error of 10%.