• Korean Journal of Remote Sensing
• /
• v.34 no.6_1
• /
• pp.879-891
• /
• 2018

In this study, the effects of urban redevelopment and building construction on the change of the detailed flows around the Pukyong National University (PKNU) campus located in the building-congested area was investigated using a CFD (computational fluid dynamics) model and GIS (geographic information system). For the analysis of the detailed flows before and after the constructions of the buildings around and within the campus, numerical simulations for the 16 inflow directions were performed before and after the construction. We used, as reference wind speeds at the inflow boundaries, the averaged wind speeds observed at the Gwangan light beacon (962) where there is no surrounding obstacle (i.e., building and terrain) acting as friction. We analyzed the area fractions in which wind speeds at z = 2.5 m changed after the construction for 16 inflow directions. The area fractions were relatively large in the east-south-easterly and southerly cases, because of the high-rise buildings constructed at the east and the apartment complex and the Engineering buildings constructed at the south of the PKNU campus. In the case of the easterly of which frequency is highest among the wind directions observed at the Daeyeon AWS (AWS 942) located inside the PKNU campus, the wind-speed change was not significant even after the constructions. It is shown that the building construction has affected the detailed flows around as well as even in the far downwind region of the constructed buildings. Also, it is shown that the GIS and CFD model are useful for analyzing the detailed flows in planning the urban redevelopment and/or building construction.

• Journal of The Korean Society For Urban Railway
• /
• v.6 no.4
• /
• pp.319-326
• /
• 2018

The safety interval to prevent collision between trains in a train control system is based on the braking distance according to the emergency braking of the train. The evaluation of the braking performance is based on the longitudinal train dynamics or the commissioning test in the test track, but since the conditions such as the weakening of the adhesion coefficient between the wheel and rail can not all be considered, these conventional methods are not sufficient to design of the train control systems. Therefore, in this study, the Monte Carlo Method (MCM) which can consider various environments is used to analyze braking performance and limitations. The braking model is based on the air braking used in the emergency braking and is modeled to take into account the braking pressure, efficiency, friction coefficient, adhesion condition, and vehicle mass distribution. It is confirmed that braking performance can be improved by controlling the quality of braking device. In addition, the change of the braking performance was confirmed according to the vehicle constituting the train. The results of this study are expected to be used as basic information for designing safety clearance for the train control systems and as a basis for improving the braking performance of railway vehicles.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.12
• /
• pp.37-46
• /
• 2023

Dynamic soil properties are essential factors for predicting the detailed behavior of the ground. However, there are limitations to gathering soil samples and performing additional experiments. In this study, we used an artificial neural network (ANN) to predict dynamic soil properties based on static soil properties. The selected static soil properties were soil cohesion, internal friction angle, porosity, specific gravity, and uniaxial compressive strength, whereas the compressional and shear wave velocities were determined for the dynamic soil properties. The Levenberg-Marquardt and Bayesian regularization methods were used to enhance the reliability of the ANN results, and the reliability associated with each optimization method was compared. The accuracy of the ANN model was represented by the coefficient of determination, which was greater than 0.9 in the training and testing phases, indicating that the proposed ANN model exhibits high reliability. Further, the reliability of the output values was verified with new input data, and the results showed high accuracy.

• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.401-410
• /
• 2003

This study investigates the biomechanical efficacies of various cement augmentation techniques with or without pressurization for varying degrees of osteoporotic femur. For this study, a biomechanical analysis using a finite element method (FEM) was undertaken to evaluate surgical procedures, Simulated models include the non-cemented(i.e., hip screw only, Type I), the cement-augmented(Type II), and the cemented augmented with pressurization(Type III) models. To simulate the fracture plane and other interfacial regions, 3-D contact elements were used with appropriate friction coefficients. Material properties of the cancellous bone were varied to accommodate varying degrees of osteoporosis(Singh indices, II∼V). For each model. the following items were analyzed to investigate the effect surgical procedures in relation to osteoporosis of varying degrees : (a) von Mises stress distribution within the femoral head in terms of volumetric percentages. (b) Peak von Mises stress(PVMS) within the femoral head and the surgical constructs. (c) Maximum von Mises strain(MVMS) within the femoral head, (d) micromotions at the fracture plane and at the interfacial region between surgical construct and surrounding bone. Type III showed the lowest PVMS and MVMS at the cancellous bone near the bone-construct interface regardless of bone densities. an indication of its least likelihood of construct loosening due to failure of the host bone. Particularly, its efficacy was more prominent when the bone density level was low. Micromotions at the interfacial surgical construct was lowest in Type III. followed by Type I and Type II. They were about 15-20% of other types. which suggested that pressurization was most effective in limiting the interfacial motion. Our results demonstrated the cement augmentation with hip screw could be more effective when used with pressurization technique for the treatment of intertrochanteric fractures. For patients with low bone density. its effectiveness can be more pronounced in limiting construct loosening and promoting bone union.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.42 no.2
• /
• pp.103-109
• /
• 2016

Efficacy of cosmetics has been mainly evaluated by qualitative and quantitative methods based on visual sense, tactile sense and skin structure until now. In this study, we suggested a novel evaluation method for skin status based on sound; measuring and analyzing the rubbing noise generated by applying cosmetics. First, the rubbing noise was measured at a close range by a high-sensitivity microphone in anechoic environment, and the noises were analyzed by 1/3 octave band analysis in frequency-domain. Three conditions, 1) before washing, 2) after washing and 3) after application of cosmetics, were compared. As a result, sound pressure level (SPL) of rubbing noise after washing was larger than that of before washing, and the SPL of rubbing noise after cosmetic application was the smallest. Furthermore, the energy of rubbing noise after application was higher than that of the before and after washing conditions in a low frequency band (lower than 2 kHz region). Conversely, the energy of rubbing noise after application was much lower than the others in a high-frequency band (upper than 2 kHz region). This change of energy distribution was described as a balloon-skin model. High SPL in the low frequency region after the cosmetic applications was due to the increase of "flexibility index", while SPL in the high frequency region significantly decreased because of the attenuation which is related to "softness index". Therefore, we developed two indices based on the spectrum-energy difference for evaluating skin conditions. This proposed method and indices were verified via skin flexibility and roughness measurement using cutometer and primos respectively. These results suggest that acoustic measurement of skin friction noise may be a new skin status evaluation method.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.4
• /
• pp.327-351
• /
• 2009

Laboratory tests are performed in this paper to investigate the brittle failure characteristics of over-stressed rocks taken in deep depth. Also, numerical simulation performed using that the so-called CWFS(Cohesion Weakening Frictional Strengthening) model is known to predict brittle failure phenomenon reasonably well. The most typical rock types of Korean peninsula - granite and gneiss - were used for testing. Results of uniaxial compression tests showed that the crack initiation stress was about 41 % to 42% of the uniaxial compressive strength regardless of rock types, where as, the crack damage stress of granite was about 75%, and that of gneiss was about 97%. Through the damage-controlled test, strength parameters of each rock were obtained as a function of damage degree. After the peak, the crack damage stress and the maximum stress were decreased, The cohesion was decreased and the friction angle was increased with increase of rock damage. Before reaching the peak, the elastic modulus was slightly increased, while decreased after the peak. Poisson's ratio was increased as the damage of rock proceeds. Comparison of uniaxial compression tests and damage-controlled tests shows the crack initiation stress estimated from the damage-controlled test fluctuated within the range of crack initiation stress obtained from the uniaxial compression test; the crack damage stress was less than that estimated from the uniaxial compression test. In order to predict the critical depth that brittle failure occurs, numerical simulations using the CWFS model were performed for an example site. Material parameters obtained from the laboratory tests mentioned above were used for CWFS simulation. Comparison between the critical depth predicted from the numerical simulation using the CWFS model and that predicted by using the damage index proposed by Martin et al.(l999), showed that critical depth cannot be reasonably predicted by the currently used damage index except for circular tunnels. A modified damage index was proposed by the author which takes the shape of tunnels other than circular into account.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.4
• /
• pp.305-330
• /
• 2023

Unlike NATM tunnels, Shield TBM tunnels have split linings. Therefore, the stress distribution of the lining is different even if the lining is under the same load. Representative methods for analyzing the stress generated in lining in Shield TBM tunnels include Non-joint Mode that does not consider connections and a 2-ring beam-spring model that considers ring-to-ring joints and segment connections. This study is an analysis method by Break-joint Mode. However, we do not consider the structural role of segment lining connections. The effectiveness of the modeling is verified by analyzing behavioral characteristics against vibration loads by modeling with segment connection interfaces to which vertical stiffness and shear stiffness, which are friction components, are applied. Unlike the Non-joint mode, where the greatest stress occurs on the crown for static loads such as earth pressure, the stress distribution caused by contact between segment lining and friction stiffness produced the smallest stress in the crown key segment where segment connections were concentrated. The stress distribution was clearly distinguished based on segment connections. The results of static analysis by earth pressure, etc., produced up to seven times the stress generated in Non-joint mode compared to the stress generated by Break-joint Mode. This result is consistent with the stress distribution pattern of the 2-ring beam-spring model. However, as for the stress value for the train vibration load, the stress of Break-joint Mode was greater than that of Non-joint mode. This is a different result from the static mechanics concept that a segment ring consisting of a combination of short members is integrated in the circumferential direction, resulting in a smaller stress than Non-joint mode with a relatively longer member length.

• Journal of Korea Water Resources Association
• /
• v.44 no.10
• /
• pp.787-795
• /
• 2011

Extreme water events such as heavy rainfalls due to recent climate change are continually increasing and their scale has also shown an increasing trend. To overcome these natural disasters, this policy study suggests securing lateral river space as an effective method for extreme flood. To support the importance of restoration and expansion of lateral river space, Gumi upstream region of the Nakdong River basin was chosen as a target area and flood reduction analysis of the washland by using LISFLOOD model have been examined. The 500-year frequency flood was simulated for the estimation of possibly occurable flood level and it turns out that the secured lateral river space on the selected site effectively lowers about 0.53 m flood level and reduces the flood damage of the city on the lower reaches of the river. In addition, based on this result, multilateral river space securing plans were compared, and conservation easement and natural disaster insurance were suggested for sustainable and cost-effective alternatives. The costs of land purchase and conservation easement for securing the river space were also compared.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.7
• /
• pp.58-65
• /
• 2019

Polymer concrete is expected to be widely used as a building material because it has a shorter hardening time and excellent compression, tensile, bending, bond strength, frictional resistance and abrasion loss compared to general concrete. The polymer concrete has excellent vibration damping performance and research on the use of various reinforcing materials is being conducted. However, in order to completely replace the general concrete and the general anti-vibration reinforcement, such polymer concrete requires an overall review of vibration reduction performance considering physical properties, dynamic properties, productivity and field applicability. In this study, the physical and dynamic properties of polymer concrete by epoxy mixing ratio were compared with those of general concrete. It was appeared that compression, tensile, bending and bond strengths of polymer concrete by epoxy mixing were significantly higher than those of general concrete. Especially, the tensile strength was more than 4 ~ 6.5 times. Based on the basic physical properties of polymer concrete, the damping ratio, which is a dynamic characteristic according to the epoxy mixing ratio, was derived through analytical models and experiments. As a result, the dynamic stiffness of polymer concrete was 20% higher than that of general concrete and the loss rate was about 3 times higher.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.86-86
• /
• 2017

마늘파종기는 파종기구동부와 파종후 파종홀의 복토역할을 하는 파종기롤러, 지면과의 마찰을 통해 바퀴의 회전토크가 발생하며 발생된 토크는 파종기 내부 동력으로 전달되어 전체 파종시스템(배종, 호퍼캠, 파종부)을 동작 시키는 기능을 수행하는 파종바퀴, 마늘종구를 한알씩 집어올려 중간이송컵으로 이송하는 자세교정컵이 포함된 배종부와 자세교정컵에서 낙하된 마늘종구를 땅속으로 파종하는 파종장치로 구성된다. 배종율 95%, 2립 배종률 5% 성능을 확보할 수 있는 기술이 개발될 경우 세계적으로도 독보적인 기술 우위를 확보할 수 있다. 이와 같은 기본적인 기능을 구현할 수 있는 컨셉모델에 대한 설계를 수행하여 시제품개발 전 기구해석과 구조해석 등을 위한 기본설계를 수행하였다. 배종율 95% 이상을 확보하기 위해서는 기존의 현장경험의 의한 설계 방식으로는 한계가 있기 때문에 시뮬레이션 및 분석 개발이 필요한데, 프레임은 고정밀 마늘종구 배종부 장착을 위한 기본 구조물로써 작동시 동력을 얻기 위한 바퀴와 연계가 되도록 설계되었으며, 호퍼는 배종 수행을 위해 마늘을 저장해 두는 통으로써 배종부와 연결된다. 배종부의 배종판이 회전함에 따라서 배종판의 홈이 호퍼 내로 들어갔다 나오면서 마늘을 집게되며, 동력 전달부는 배종판을 회전시켜주고, 회전 속도 조절을 가능하게 한다. 파종부는 배종부에서 중간컵을 통해 하나씩 공급해준 마늘을 땅에 심는 부분으로서. 프레임의 바퀴 회전과 연동되어 회전하고 설계하였다. 배종판에서 중간컵으로 이송된 마늘을 파종부의 파종컵에 받아 회전하면서 땅속에 파종컵이 묻히면 파종컵이 열리면서 땅속에 마늘을 심는 원리이다. 조간조정은 7조식의 경우 초기설치시 고정되도록 설계되었으며 농촌진흥청 기계화 표준재배안에 따라 의성마늘 기준 $14{\times}14cm$(조간${\times}$주간)를 기준으로 개발하였다. 조간조정은 기계가 설치되면 조정하기 어려우므로 14cm로 설계하였으며, 주간조정은 원형배종장치의 구동기어부의 속도비로 간격을 조정할 수 있도록 기어장치를 설계하였다. 주간조정은 13에서 18cm의 범위에서 작동하도록 설계되었으며, 필요에 따라 간격조절이 가능함. 마늘은 그 크기가 다르고, 형상도 다르기 때문에 종자에 따른 개별적인 파종기술들이 개발되어야하기 때문에 개발 기간이 오래 걸리고, 수익에 비하여 개발비가 과다하게 요구되는 실정인데 축적된 시뮬레이션 툴을 이용한 파종기 분석 기술을 확보할 경우 다른 파종기의 연구 개발에도 크게 도움이 될 것으로 기대되며, 생육측정 실험과 동역학 해석 툴 RecurDyn을 통해 파종기의 기구학적 분석을 통한 설계반영 인자를 도출할 계획이다.