• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.47 no.5
• /
• pp.52-61
• /
• 2010

The use of the friction coefficient is known to provide good discrimination ability in the classification of human constitutions, which are used in alternative medicine. In this study, a system that uses a multi-axis load cell and a hemi-circular probe is designed. The equipment consists of a sensor (load cell type, manufactured by the authors), an x-axis linear-bush guide motorized mobile stage that supports the hand being analyzed, and a signal conditioner. Using the proposed system, the friction coefficients from different constitutions were compared, and the relative repeatability error for the friction coefficient measurement was determined to be less than 2 %. The direction along the ring finger line was determined to be the optimum measurement region for a constitutional diagnosis between Tae-eumin and Soyangin types using the proposed system. There were some differences in the friction coefficient between the two constitutions, as reported in ancient literature. The proposed system is applicable to a quantitative constitutional diagnosis between Tae-eumin and Soyangin types within an acceptable level of uncertainty.

• Proceedings of the KSEEG Conference
• /
• 2007.04a
• /
• pp.187-189
• /
• 2007

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.703-703
• /
• 2013

다이아몬드상 탄소 박막(Diamond-like carbon, DLC) 박막은 낮은 마찰 계수, 높은 내마모성, 화학적 안정성, 적외선 영역에서의 높은 투과율 등의 장점을 바탕으로 MEMS (Micro-Electro Mechanical System) 소자와 MMAs (Moving Mechanical Assemblies)의 고체윤활코팅, 마그네틱 미디어와 하드디스크의 슬라이딩 표면 등 다양한 분야에 코팅소재로써 응용되어왔다 [1,2]. 현재 전기철도용 집전판은 마찰이 적고 전도성을 지니는 카본 소재로 구성되어 있다. 그러나 그 마모 비율이 너무 심하여 이를 개선할 수 있는 방안으로 고경도 저마찰력을 지니는 DLC 박막을 코팅 소재로써 제안하고자 한다. 그러나 기존에 DLC 박막은 절연특성이 매우 우수하기 때문에 기존에 전도성을 지니는 카본 집전판에 적용하기에는 어려움이 따른다. 따라서 DLC 박막 내에 실리콘(Si) 또는 금속(Metal)을 첨가시키거나, 금속 중간층을 포함시켜 전기적으로 전도특성을 향상시키는 방안이 제시되고 있으며, 본 연구에서는 DLC 박막과 유사하게 우수한 경도특성을 지니고, 낮은 마찰계수등을 지니는 비정질 탄소박막을 연구하여 카본 집전판에 코팅하고자하며, 특히 비정질 탄소박막에 금속 Ti를 도핑하여 집전판과의 접착력과 전기적 전도 특성을 향상시키고자 한다. Ti가 도핑된 탄소박막(TiC) 박막은 비대칭 마그네트론 스퍼터링(unbalanced magnetron sputtering; UBMS) 시스템을 이용하여 제작하였으며, 스퍼터링 조건 중 기판에 인가되어지는 기판온도에 따라 변화되어지는 TiC 박막의 트라이볼로지(Tribology) 특성을 고찰하고자 하였다. 증착시 기판온도의 증가는 TiC 박막의 경도, 마찰계수 특성등 트라이볼로지 특성을 향상시켰으며, 전기적 전도 특성을 향상시켰다. 이러한 결과는 스퍼터링 방법에 의해 증착되어진 TiC 박막내에 존재하는 sp2 결합과 관계가 있음을 확인할 수 있으며, 트라이 볼로지 특성은 TiC 박막내에 sp2 탄소결합의 비율 증가와 관련되어졌다. 특히 sp2 탄소결합은 TiC 박막 증착시 증가된 기판온도와 밀접한 관계가 있으며 기판온도의 증가에 따라 나노결정 클러스터의 크기와 수의 변화와 밀접한 관계가 있음을 확인하였다. 결국 기판온도는 TiC 박막의 트라이볼로지 특성을 향상시켰으며, 전기적 특성 또한 향상시켜 전기철도 집전판에 응용을 위한 소재로 평가할 수 있다.

• Science of Emotion and Sensibility
• /
• v.14 no.2
• /
• pp.191-196
• /
• 2011

Fabric extraction force measured through nozzle tester reflects a comprehensive fabric handle. Nozzle tester takes advantage of low cost, and simple and fast operating procedure compared with KES system. The paper is to develop the semi-emprical equation for assessment of the fabric handle measured with nozzle tester on the basis of friction law. The variables considered in the equation arc fabric's frictional coefficient and drape coefficient which is determined in terms of fabric bending length and shear strain. The experiment of 12 different cotton and polyester fabrics and comparisons between experimental and theoretical results were conducted. Fabrics of high frictional coefficients, high bending length, and low shear strain showed high fabric handle forces (low handle values). The handle forces predicted from the equation agreed well with those measured, which indicates that the equation can be used to objectively evaluate fabric handle with respect to fabric's own properties and also provide an information for fabric design to improve the handle performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.6
• /
• pp.775-782
• /
• 2013

In this study, as a series of studies aimed at investigating the spatial randomness of fatigue crack growth for friction stir welded (FSWed) 7075-T651 aluminum alloy joints, the fatigue crack growth behavior of FSWed 7075-T651 aluminum alloy joints was investigated for LT orientation specimens. Fatigue crack growth tests were conducted under constant stress intensity factor range (SIFR) control for 5 specimens of the FSWed 7075-T651 aluminum alloy, including base metal (BM), heat affected zone (HAZ), and weld metal (WM) specimens. The mean fatigue crack growth rate of WM specimens was found to be the highest, whereas that of HAZ and WM specimens was the lowest. Furthermore, the variability of fatigue crack growth rate was found to be the highest in WM specimens and lowest in BM specimens.

• Elastomers and Composites
• /
• v.36 no.1
• /
• pp.3-13
• /
• 2001

To resolve environmental problem of waste tire and asbestos and also to capitalize the wastes, we developed a new kind of friction material using scrap tire, potassium hexatitanate, filler, and friction modifier in which rubber made a continuous phase. The material containing 5, 20, 10, 20phr of potassium hexatitanate, phenol, friction modifier, $BaSO_4$, respectively showed good friction properties, high and stable coefficient or friction, and low wear rate.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.421-430
• /
• 1997

In this study, the static and the fatigue tests were performed with high tension bolted joints, of which the surfaces were spread with inorganic zinc-primer after shot-blast, and milling surface, and steel-natural surface, difference of friction surface condition were examined by comparing the esults of tests. From the result of synthetical investigation of this study. it is proper that using the torque management method in order to introduce design axial force to blots, and the provision of specifications that initial axial forces must be 110% of design axial forces is proper. Decreasing ratio of axial forces to initial force is proportional to common lorgarithms of time progress, it converge constant value after 20 hours, and decreasing ratio is little related to the roughness of friction surface. Sliding coefficient of milling, spreading inorganic zinc-primer, just producting is great in order and sliding forces are dependent on the applied axial forces, but if the applied axial forces are great, sliding coefficient become small by a loss of roughness. So it is confirmed that relation between the applied axial forces and the sliding forces are not proportional linearly. From the result of estimation on fatigue strength, all specimens satisfy the specifications with B-grade and milling surface is lower than the others about 14% in fatigue strength because in milling surface lose the function of friction-types joints at lower number of cycles. From the result of eximination for the distribution area of compressive force, friction area near to inside bolt is wider in the direction of stress than near to outside. It is guessed that this situation occurs because outside bolts firstly change from the friction connection to the bearing connection.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.465-470
• /
• 2002

For measuring friction-factor of artificially-roughened surfaces which are usually applied on damper seals, flat plate test apparatus is designed and fabricated. the measurement of leakage and pressure distribution through round-hole pattern specimen with different hole area is described and a method is discussed for determining the friction-factor experimentally. Results show that the friction-factor of the round-hole pattern surfaces is bigger than that of smooth surface and increases as increasing the hole area. A empirical friction factor model for round-hole pattern surface is defined as the Moody's friction factor formula.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1988.06a
• /
• pp.43-48
• /
• 1988

보호피막을 입히는 방법으로는 화학증착법과 물리증착법이 주로 사용되고 있다. 고온 분위기에서 기체 상태인 반응물의 화학반응을 통하여 원하는 물질을 증착시키는 화학증착법은 물리증착법에 비해 점착성(adhesion)이 우수하고, 보호피막층의 성분조절이 용이하며, 반응물이 기체상태이므로 대량생산이 용이하여 보호피막 증착법으로 많이 사용되고 있다. $Si_3N_4$-TiC ceramic 표면에 TiC, TiN 및 Ti(C, N) coating을 함으로써 얻을 수 잇는 장점들은 표면층의 경도를 증가시키며, steel과의 마찰계수의 감소 및 coating 층 자체가 고온에서 고체 윤활제로 작용하여 마찰열의 상당한 감소를 얻을 수 있으며, 또한 coating층 자체가 비교적 안정한 화합물로 피삭재내의 성분원소들에 대한 diffusion barrier로 작용되며, 내식성을 증가시킬 수 있다. 본 연구에서는 각 증착층의 미소경도, 열충격저항, steel과의 마찰계수를 측정하였으며, 최종적으로 절삭시험을 통하여 증착층들의 내마모성을 조사, 규명하였다.

• The KSFM Journal of Fluid Machinery
• /
• v.6 no.3 s.20
• /
• pp.15-20
• /
• 2003

For measuring friction factor of artificially-roughened surfaces which are usually applied to damper seals, flat plate test apparatus is designed and fabricated. The measurements of leakage flow and pressure distribution through round-hole patterned specimen with different hole areas are described, and a method is discussed for determining the friction factor experimentally. Results show that the friction factor of the round-hole patterned surface is bigger than that of smooth surface, and increases as increasing the hole area. A empirical friction factor model for the round-hole patterned surface can be descrived by the Moody's friction factor formula.