• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.5
• /
• pp.461-467
• /
• 2012

An experimental study was carried out to measure frictional pressure drop in flow boiling to deionized water in a microchannel having a hydraulic diameter of $500{\mu}m$. Tests were performed in the ranges of heat fluxes from 100 to $400kW/m^2$, vapor qualities from 0 to 0.2 and mass fluxes of 200, 400 and $600kg/m^2s$. The frictional pressure drop during flow boiling is predicted by using two models; the homogeneous model that assumes equal phase velocity and the separate flow model that allows a slip velocity between two phases. From the experimental results, it is found that the two phase multiplier decreases with an increase in mass flux. Measured data of pressure drop are compared to a few available correlations proposed for macroscale and mini/microscale. The homogeneous model well predicted frictional pressure drop within MAE of 29.4 % for the test conditions considered in this work.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.31-37
• /
• 2011

직조 금속 스크린 리브(rib) 이 바닥에 설치된 사각 덕트에서 열전달과 유체유동의 압력강하를 측정하기 위해 실험적 연구를 수행하였다. 시험부의 치수는 200 mm(W) ${\times}$ 40 mm(H) ${\times}$ 712 mm(L)이고 수력직경은 66.6 mm이다. 입구영역에는 1.72m 길이의 가열되지 않은 동일한 치수의 채널을 설치하였다. 메쉬가 다른 4가지의 직조금속 스크린 리브에 대해 측정하였다. 그리고 비교를 위해 일체형 리브에 대해서도 측정하였다. 국부 열전달 계수의 측정에는 스테인레스 강제 포일(foil) 히터와 T형 열전대률 이용하였다. 레이놀즈 수는 23,000에서 58,000의 범위이다. 덕트의 수력직경($D_h$)에 대한 직조 금속 리브의 높이(e)의 비($e/D_h$)는 0.075 이고 리브 간격(p)과 높이의 비(p/e)는 10이다. 실험 결과 메쉬가 없는 일체형 리입에서 가장 누셀트 수와 마찰계수가 컷다.

• The korean journal of orthodontics
• /
• v.37 no.5
• /
• pp.341-350
• /
• 2007

The purpose of this study was to evaluate how the friction that occurs during the sliding movement of the archwire through esthetic brackets is differently affected by bracket materials, slot designs, and tip angulations of the archwire. Methods: Eight types of brackets with 0.018 inch slots (composite: Brillant (BR); composite with metal slot: Spirit MB (SP); ceramic: Inspire (IN), Signature (SI), Cristaline V (CR); ceramic with metal slot: Clarity (CL), Luxi II (LU); and metal bracket: Integra (IT)), and placed into groups of 20 brackets in each group, were tested in artificial saliva with 0.018 inch stainless steel wire. The wire tip angulations were given as 0, 4 and 8 degrees. Results: CR group significantly showed the lowest frictional force with all wire tip angulations of 0,4, and 8 degrees. IN significantly showed the highest frictional force (p < 0.001). BR (polyoxymethylene) had significantly less frictional force than SP (polycarbonate) (p < 0.001) and showed no significant difference between metal brackets. Friction was increased as the wire tip angulations were increased, but no notches were observed on any parts of the archwire. Conclusions: According to the results of this study, esthetic brackets are superior or similar to 55 brackets from a frictional point of view.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.2
• /
• pp.226-232
• /
• 1983

회전수를 용접변수로 했을 때 이종강봉 및 이종강관의 마찰용접에 있어서 소성변형중에 발생한 AE(acoustic emission)량과 용접후의 냉각중에 발생한 AE량의 총량을 측정해석하고, 용접표면상 에 0.635mmR의 반원 노치를 가공했을 때의 용접부 인장강도를 구하여, AE총량과 용접부강도와 의 상관관계실험식 모델을 만들었고, 이들과 관계계산식과의 비교 조사와 95%신뢰성을 검증하였 고, 이종강의 마찰용접 중에 용접강도와 품질을 검토관리할 수 있는 기본자료가 되게 하였다.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.1
• /
• pp.93-103
• /
• 2005

Both static pile load test with load transfer measuring system and the pile dynamic load test are performed to estimate the skin friction and behavior characteristics of a large drilled shaft. And the numerical modeling of large drilled shaft is performed by applying the FDM program. Since the magnitude of friction resistance depends on the relative displacement between soil and shaft, load and displacement at the arbitrary depth along the large drilled shaft are estimated to analyze the correlation. According to the measuring results of load transfer, unit skin friction along the large drilled shaft was fully mobilized at gravel layer in the middle of shaft and the frictional resistance transmitted to bedrock was relatively small. Also, even for the same drilled shaft, the results of PDA and static load test are different with each other and the difference is discussed.

• Science of Emotion and Sensibility
• /
• v.4 no.2
• /
• pp.79-88
• /
• 2001

The objectives of this study were to investigate the relationship of sound parameters with subjective sensation and physiological responses, and to figure out the interrelationship between the subjective sensation and physiological responses. Sound parameters calculated were LPT, ΔL, Δf, loudness[Z], and sharpness[Z]. Subjective sensation was evaluated in 7 aspects(soft-hard, loud-quiet, pleasant-unpleasant, sharp-dull, clear-obscure, rough-smooth, high-low) by thirty participants. We acquired physiological responses when each fabric sound was presented to 10 participants. Physiological signals obtained in this study were electroencephalogram(EEG), pulse volume(PV), skin conductance level(SCL), and LF/HF of heart rate variability. The larger the values of loudness[Z] and LPT, the louder and the rougher the subjective sensation of the perceived fabric sound. Also, the larger the values of loudness[Z] and LPT, the harder, the duller, and the less pleasant. As LPT increased, PV decreased. Loudness[Z] increased in proportion to SCL and so did sharpness[Z] to LF/HF. As the sound perceived to be quieter and clearer, the relative power of slow alpha rose. As the sound perceived to be more pleasant and smoother, PV rose.

• Journal of the Korean GEO-environmental Society
• /
• v.6 no.1
• /
• pp.45-51
• /
• 2005

The distribution of shaft resistance is measured by the static load test with the strain gauge or stress gauge, so that the long-term load distribution must be considered for the pile design. However, the measurement by strain gauge generally assumes the 'zero reading', which is the reading taken at 'zero time' with 'zero' load and the residual stress, which is the negative skin friction(or the negative shaft resistance) caused by the pile construction, is neglected. Therefore, the measured value by strain gauge is different from the true load-distribution because residual stresses were neglected. In this study, the three drilled shafts were constructed, and the strain measurements were carried out just after shaft construction. As a result of this study, it is shown that the true load-distribution of drilled shaft is quite different with known load distribution and the true load-distribution of drilled shaft changed from the negative skin friction to the positive skin according to the load increment.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.5
• /
• pp.354-358
• /
• 2015

The results of between resistance and optical transparency measurement in DOT-3 brake fluid contaminated moisture and particles generated from fraction of brake system was compared. Conventional resistance measurement method was known to be effaced by it's hygroscopic characteristics. However, the particle is a significant element of the contamination sources. Proposed optical transparency measurement is linear and effective than that of contamination in brake fluid.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.516-520
• /
• 2011

본 논문에서는 먼저 흥인지문에 대해 상시진동실험을 수행하고, 그 데이터를 분석하여 흥인지문의 고유진동수, 모드, 감쇠비의 특성을 분석하였다. 그 결과로부터 흥인지문의 병진모드를 파악하였고, 병진모드에서 측정한 여러 기둥의 모드 상대크기와 위상이 동일함을 확인하였다. 저차 병진모드에서 모든 기둥이 같은 방향으로 강성을 발휘하기 때문에 각층의 강성을 합한 등가의 층강성을 가지는 2자유도의 동적강체해석모델을 제시하였다. 이 해석모델은 선형 범위 내에서 거동한다는 것으로 가정하여 층강성을 산정하였다. 실제 흥인지문의 접합부에는 부재간의 이음과 맞춤에 의한 마찰력이 작용한다. 접합부를 누르는 무거운 지붕하중에 의해 이 마찰력은 증가하게 되고, 이로써 횡하중에 저항하게 된다. 이러한 접합부에 강한 횡하중이 작용하게 되면, 접합부의 이완 및 마찰력의 저하 등으로 인하여 횡강성의 저하가 급격히 일어나는 비선형 특성을 갖게 된다. 이러한 흥인지문의 비선형적인 특성을 파악하기 위해 흥인지문 해석모델에 쿨롱 마찰력을 도입하여 비선형적인 해석모델을 제시하였다.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.301-315
• /
• 2001

본 연구에서는 최근 5년간 국내 각 지역에서 채취한 802개의 절리면 시료에 대하여 전단시험을 실시하여 얻은 결과를 이용하여, 절리면의 여러 공학적 성질들을 조사, 연구하였다. 절리면 전단시험에서 얻어진 최대마찰각 및 잔류마찰각을 지체구조별, 암종별로 분류하고 통계적으로 구하였으며, Barton의 전단강도식의 입력변수인 JRC, JCS를 측정하고 Barton식의 적용성에 대해서도 검토하였다. 그 결과 설계의 기초자료로 활용할 수 있는 지역별, 주요 암종별 최대마찰각, 잔류마찰각을 제시하였다. 또한, JRC, JCS, 수직응력에 따른 마찰각과 전단강성 및 팽창각의 변화를 분석하였다. 마지막으로, Barton의 식에서 구한 이론적 전단강도와 이 실험에서 얻어진 전단강도를 비교한 결과, Barton의 경험식은 높은 상관도로 암석 절리면 전단강도를 예측할 수 있음을 확인하였다.