• Journal of Biosystems Engineering
• /
• v.7 no.2
• /
• pp.57-71
• /
• 1983

마찰식 정미기의 성능에 영향을 미치는 기계설계 및 작동상의 인자로는 스크린의 형태, 롤러의 형태, 롤러회전속도, 출구 저항 등 여러가지가 있다. 이러한 요인들에 대한 연구가 본 논문의 저자에 의해서 시리즈로 연구되어 왔으며, 본 연구는 그의 일환으로 스크린의 단면형상(6각, 8각, 12각 그리고 원통형), 스크린에 뚫려있는 슬랏의 기울기($15^{\circ}$, $30^{\circ}$, $45^{\circ}$ 그리고 $-45^{\circ}$), 그리고 출구 저항이 정백미의 질과 양, 정백효율 그리고 정백실내의 정백압력 등에 미치는 영향을 규명하기 위해 수행되었다. 이 실험에 사용된 공시 정미기는 임도정 공장에서 널리 사용되고 있는 흡입마찰식이었며, 사용된 시료는 밀양 23호인 통일계품종이었다. 각 처리마다 동력 소모량과 정백실내의 정백압력을 측정하기 위해서 "KYOWA" 스트레인 게이지 시스템(strain gauge system), 토오크 변환기, 압력변환기 등이 사용되었다. 본 실험 결과를 요약하면 다음과 같다. 1) 정백과정중에 정백실내의 정백압력은 입구에서 가장 높았고 출구쪽으로 갈수록 점차 감소하였다. 평균 정백압력도 순환 횟수에 따라서 변화 하였는데 첫번째 순환에서 가장 높았고 순환횟수가 증가함에 따라 감소하였다. 2) 본 실험에서 사용한 출구저항 수준은 출구저항 수준 1에서 요구되는 정백도의 백미를 얻기 위한 순환 횟수는 2회 이었고 출구저항 수준 2에서는 4회 이었는데, 이를 출구저항 수준이 정백압력, 정백율, 완전미수율 및 도정 효율에 가장 큰 영향을 주었다. 3) 스크린에 뚫려있는 슬랏 각도가 $15^{\circ}$에서 $45^{\circ}$로 증가함에 따라서 정백실내의 평균 정백압력은 감소하였고, 완전미수율과 도정 효율은 증가하였으나, 일반적으로 도정수율은 감소하는 경향을 보였다. $-45^{\circ}$의 슬랏 각도를 가진 스크린에서는 슬랏 각도 $15^{\circ}$인 스크린에서와 거의 비슷한 정백압력 수준을 나타냈으나 완전미와 정백미의 생산은 매우 낮았다. 4) 스크린 표면에 기다란 강편 (보통 "띠"라고 부름)을 붙인 원통과 12각형의 스크린에서는 강편을 붙이지 않은 6각형과 8각형 스크린에서 보다는 비교적 높은 정백압력을 나타냈다. 전자는 후자에 비해서 정백효율은 높았으나 완전미수율은 떨어졌다. 5) 정백실내에서 가장 낮은 정백압력을 나타낸 8각형 스크린은 높은 도정수율과 완전미수율을 가져왔으나 상대적으로 정백효율은 낮게 나타났다. 6) 정백실내의 반경 방향의 평균 정백압력($P_R$)과 완전미수율($Y_h$)은 다음과 같은 1차적인 역비례 관계가 있었으며(평균 정백압력 범위는 0.5-0.9kg/$cm^2$), $Y_h=-28.661P_R+84.860$ ($r^2=0.858$) 정백효율($Y_e$)과 정백압력($P_R$) 사이에는 다음과 같은 2차적인 관계가 존재함을 알 수 있었다. $Y_e=-597.5P_{R^2}+929.96P_R-210.15$ ($r^2=0.759$) 정백효율은 정백압력이 0.7-0.8kg/$cm^2$일 때 가장 높았으며, 이때 변이도 가장 심한 것으로 나타났다.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.9 no.1
• /
• pp.1-7
• /
• 1976

1) The decrease in strength of netting twines at the knot may be regarded to be due mainly to the frictional force acting on the tip of the knot. The knot strength T may be given by $$T=\frac{T_0}{1+{\mu}\frac{s}{\rho}\varrho^{\mu\theta}$$ were $T_0$ is the tensile strength of unknotted netting twines, $\mu$ the coefficient of friction beween two netting twines forming a knot, s the contact length between the tip and the netting twine compressing it, $\rho$ the radius of curvature of the compressing, and $\theta$ the angle at which the compressing rubs with another one in the vicinity of the opposite tip. 2) Knots are arranged in order of strength as follows : the reef knot pulled lengthwise $\risingdotseq$ the trawler knot pulled breadtwise the reef knot pulled breadthwise.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.1
• /
• pp.39-53
• /
• 2018

Generally, the total ventilation resistance coefficient in a tunnel consists of inlet/outlet loss coefficient, wall friction coefficient, and other loss coefficient caused by sudden expansion and contraction of cross-section, etc. For the tunnel before opening, when the running ventilation fan is stopped, the wind speed in the tunnel is reduced by the total ventilation resistance drag. The velocity decay method is comparatively stable and easy to estimate the wall friction coefficient in the pre-opening tunnel. However, the existing study reported that when the converging wind speed is a negative value after the ventilation fan stops, it is difficult to estimate the wall friction coefficient according to the velocity decay method. On the other hand, for the operating tunnel in which the piston effect acts, a more complex process is performed; however, a reasonable wall friction coefficient can be estimated. This paper aims at suggesting a method to minimize the measurement variables of the piston effect and reviewing a method that can be applied to the operating tunnel. Also, in this study, a new method has been developed, which enables to calculate an variation of the piston effect if the piston effect is constant with a sudden change of external natural wind occurring while the wind speed in the tunnel decreases after the ventilation fan stops, and a programming logic has been also developed, which enables dynamic simulation analysis in order to estimate the wall friction coefficient in a tunnel.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.4
• /
• pp.59-67
• /
• 2004

Direct numerical simulations of turbulent flows over riblet-mounted surfaces are performed to educe the mechanism of drag reduction by riblets. Numerical simulations are performed for flow fields with R $e_$\tau$/=180. For riblet ridge angle $\alpha$=60$^{\circ}$, two different riblet spacings of $s^+/=20 and 40 are used in this study. The computed drag on the riblet surfaces is in good agreement with existing computational and experimental data. The mean velocity profiles show upward and downward shifts in the log-law for drag-decreasing and drag-increasing cases, respectively Turbulence statistics above the riblets are computed and compared with those above a flat plate. The purpose of this study is in two categories: first, to understand the drag reduction mechanism on riblet surface, second, to verify our own code by comparison of the present results with those from previous studies.udies.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.9 no.4
• /
• pp.293-298
• /
• 1976

1) The decrease in strength of netting twines at the twisted joint is regarded to be due mainly to tile frictional force between plied yarns, but tile rate of decresae is within $5\%$ in filament twines and 5 to $10\%$ in spun twines. 2) The variation of the twisted joint strength with the angle between the two adjacent bars draws a parabola flaying the minimum value at tile angle of $90^{\circ}$. The minimum value was revealed as about $90\%$ of the strength at the angle of $0^{\circ}$ in wet spun twiness, but regarded to hi negligibly small filament twines. 3) The knot strength is about $30{\pm}5\%$of the twisted joint strength.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.2
• /
• pp.49-57
• /
• 2014

In this study, in order to take advantage of samples collected in the Jangbogo station, and to grasp the liquefaction resistance characteristics of the dynamic load was performed cyclic triaxial test. Also, through the comparison with the existing literature. The test results, for the relationship between number of cycles for the same cyclic shear stress ratio and the cyclic shear stress ratio to produce an axial strain of 5%, in all samples, the cyclic shear stress ratio to liquefaction for the specimen, which has been liquefied, was increased, whereas number of cycles were reduced. The cyclic shear stress ratio of samples first decrease up to the fine content of about 10%. After this strength level, there is a little increase in cyclic shear stress ratio with increasing fine content. In addition, the cyclic shear stress ratio between cohesive strength, mean particle size, and friction angle decrease but some time later, there was a tendency that cyclic shear stress ratio is a little increased.

• Tribology and Lubricants
• /
• v.6 no.1
• /
• pp.82-88
• /
• 1990

In order to investigate tribological effects of coatings on different places on tool wear, commercial quality coated inserts were tested in production speed machining after the coatings on clearance or rake face of coated tools were selectively removed. The experimental results demonstrated that the primary role of coatings in tool wear was the reduction of the thermochemical adhesion between the tool material and workpiece. And the coating on rake face was observed to retard the progress of flank wear. In case of machining carbon steel, multicoated tools showed the most favorable results for considering the notch wear.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.176-186
• /
• 1996

The phenomena of drag reduction using small quantities of a liner macromolecules has attracted the attention of many experimental investigations. On the other hand drag reduction in two phase flow can be applied to the transport of crude oil, phase change system such as chemical reactor, pool and boiling flow, and to flow with cavitation which occurs pump impellers. But the research on dragreduction in two phase flow is not sufficient. The purpose of the present work is to evaluate the drag reduction by measuring pressure drop, void fraction, mean liquid velocity and turbulent intensity whether polymer additives a horizontal single and two phase system or not. Flow pattern of air-water two phase flow was classified by electrical conductivity probe signal. Velocities and turbulent intensities of signal were measured simultaneously with a Hot-film anemometer.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.5
• /
• pp.679-686
• /
• 1999

This study is to investigate the effect of a substantial drag reduction caused by the polymer(A611P) when the working fluids flow to the vertical direction in the vertical cylindrical equipment of closed flow system. The drag reduction is associated with the mechanical degrada-tion thermal degradation and heat transfer. By ignore the heat fluxs within the closed system the pressure drop due to the polymer concentration the flow velocity and flow time have been mea-sured. By taking into account the mechanical and thermal degradation in the closed system an experiment has been focused on the determination of the condition which could improve the pump capacity in the heat union electric power plant. Under the condition of non-boiling it has been found out that the change of heat flux has little influence on the drag reduction.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.30 no.3
• /
• pp.95-102
• /
• 2018

As a recent technical approach, a high-speed planing hull was tried to realize a friction reducing system by simultaneously actuating the triple streamlined step hull form in association with optimum speed of 35 knot planing for fishing boat. In this approach, the streamlined step hull form with triple structure of type was attached under the bottom of high-speed planing hull, while a friction resistance is reduced in the process of running at the speed of 35 knot. In addition, this research was to make a performance test as to the manufactured product and acquire the purposed values and the development items. Actually, after manufacturing the desired prototype of high-speed planing hull, the significant items, fuel efficiency (second) and amount of fuel consumption (degree) including maximum speed (knot) were estimated for a performance test. And tensile strength (MPa) and bend strength (MPa) as to the completed prototype like a high speed planing hull were also acquired during the test.