• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.2
• /
• pp.46-54
• /
• 2007

We have fabricated and characterized MMI (Multimode Interference) coupled ring resonator with the total internal reflection mirrors and the semiconductor optical amplifier for the integration of the WDM (Wavelength Division Multiplexing) system. The TIR (Total Internal Reflection) mirrors were fabricated by self-aligned process and had losses of about 0.71 dB per mirror. Coupling in and out of a resonator was achieved using the extremely small MMI couplers. The MMI length and width used in the experiment were $119{\mu}m$ and $9{\mu}m$, respectively. The resulting FSR (Free Spectral Range) and on-off ratio were approximately 1.333 nm (162 GHz) and 13 dB, respectively.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.82-85
• /
• 2002

본 논문에서는 접지면에 어퍼쳐를 갖는 협대역 hairpin-comb 대역 통과 여파기를 제안하였다. Hairpin-comb 공진기는 두 공진기 사이의 간격이 매우 좁더라도 약한 커플링을 유지하는 특성이 있으므로 협대역 대역통과 여파기 제작시 여파기의 전체적인 크기를 작게 할 수 있는 장점이 있다. 그러나 일반적인 마이크로스트림에서는 공진기 사이가 최소한의 거리가 되더라도 커플링이 너무 미약하여 사용할 수 없다, 그러므로 접지면의 어퍼쳐를 사용하여 약한 커플링을 보상함으로써 일반 마이크로 스트립에서도 협대역을 대역통과 여파기를 제작할 수 있었다. 또한 공진기 사이의 거리변환 없이 어퍼쳐의 크기에 의해서 커플링을 조절함으로써 전체 여파기의 크기를 고정시킨 상태에서 대역폭을 조절할 수 있는 장점이 있다. 본 논문에서는 중심 주파수가 1.78 ㎓ 이고 대역폭이 62MHz(3.5%)인 여파기를 제작하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.20-26
• /
• 2003

This paper presents hairpin-comb bandpass filter using ground aperture. Hairpin-comb resonator maintains the weak coupling though the space between two resonators is very small. This has the good merit that the entire filter size is small for narrowband bandpass filter. The coupling between two hairpin-comb resonators so very weak that can't be applicable to general microstrip. We compensate the coupling by using ground aperture. It makes the hairpin-comb filter possible that can be applicable to general microstrip. Also it has the good merit which adjusts the bandwidth by changing the size of aperture without changing the space. In this paper, we fabricate the bandpass filter, which has 1.78 GHz center frequency and 62 MHz (3.5%) fractional bandwidth.

• Korean Journal of Optics and Photonics
• /
• v.27 no.5
• /
• pp.181-187
• /
• 2016

We report on the parameter-dependent optical characteristics of the unidirectional single-mode lasing square ring cavities. Using the taper-step section in the square cavities, the resonant direction can be selected and we characterize the optical losses by changing the taper lengths. Various kinds of square ring cavities are fabricated, based on InGaAsP/InGaAs multiple quantum well semiconductor materials. From the experimental results we obtain the optimized taper length for a given device structure, while maintaining unidirectional single-mode lasing.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.71-74
• /
• 2000

본 논문에서는 무선LAN용으로 사용할 수 있는 마이크로 스트립을 이용한 대역동과 필터를 설계하였다. 기존의 링이나 square loop의 구조를 이용한 공진기와는 다르게 cross loop 와 meander loop의 구조를 이용한 공진기를 혼합한 형태로써 크기가 상당히 줄어든 새로운 구조와 BandPass Filter를 설계하였다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.5
• /
• pp.42-48
• /
• 1979

In this paper, it is shown that a microwave frequency discriminator can be realized by use of a simple ring resonator. Its characteristics have been analyzed by employing Green's function and verified experimentally. The maximum frequency bandwidth obtained from the experiments is 45MHz at S-band(center frequency 50=3GHz).

• Korean Journal of Optics and Photonics
• /
• v.16 no.5
• /
• pp.469-475
• /
• 2005

An integrated photonic microwave bandpass filter has been proposed and demonstrated incorporating a coherently coupled microring resonator in low-loss polymers. The proposed device may feature compact site, simple structure, tuning via the thermooptic and electrooptic effect, and flexible integration with other electrical and optical devices. The resonator was designed to have an extremely small bandwidth so that it could be used to selectively pass the optical signal carrying the microwave signal to attain efficient bandpass filtering. We made and tested two resonators with a single ring and double rings, and performed a theoretical fitting of their measured transfer curves to predict the performance of the microwave filters based on them precisely. It was found that as the number of the rings used for the resonator increases, the bandwidth gets smaller, the rolloff sharper, and the band rejection higher. Finally our filter exhibited the center frequency of 10GHz, the 3-dB bandwidth of 1.0GHz, the corresponding quality (Q) factor of 10, and the rejection outside of the passband of more than 25dB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.2
• /
• pp.273-279
• /
• 2013

In this paper, a novel split ring resonator is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator, and oscillator for 5.8GHz band is designed using proposed split ring resonator. At the fundamental frequency of 5.8GHz, 7.22dBm output power and -83.5 dBc@100kHz phase noise have been measured for oscillator with split ring resonator. The phase noise characteristics of oscillator is improved about 9.7dB compared to one using the general ${\lambda}$/4 microstrip resonator. Because it is possible that varactor diode or lumped capacitor is placed on the gaps of split ring resonator, resonant frequency can be controlled by bias voltage. We can design voltage controlled oscillator using proposed split ring resonator. Thus, due to its simple fabrication process and planar type, it is expected that the technique in this paper can be widely used for low phase noise oscillators for both MIC and MMIC applications.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.3 no.2
• /
• pp.25-30
• /
• 2010

In this paper, a novel notch resonator is proposed based on Rectanglar Split Ring Resonator (R-RSS) element. We represented the electrical characteristics for R-SRR elements coupled with microstrip line, and measured result is compared with electromagnetic simulation (HFSS) result. We also solved equivalent circuit for R-SRR element, and also discussed influences of change structural parameters of R-SRR. the size of R-SRR is the most important parameters for frequency tuning. Also we can make tunable resonator form the basic structure. This novel resonator can apply to design of tunable bandpass filter and voltage control oscillator.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.7
• /
• pp.1538-1543
• /
• 2013

In this paper, a novel split ring resonator is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator. Oscillator using proposed split ring resonator is designed, it has improved phase noise characteristics. At the fundamental frequency of 5.8GHz, 7.22dBm output power and -83.5 dBc@100kHz phase noise have been measured for oscillator with split ring resonator. The phase noise characteristics of oscillator is improved about 9.7dB compared to one using the general ${\lambda}/4$ microstrip resonator. Next, we designed voltage controlled oscillator using proposed split ring resonator with varactor diode. The VCO has 125MHz tuning range from 5.833GHz to 5.845GHz, and phase noise characteristic is -118~-115.5 dBc/Hz@100KHz. Due to its simple fabrication process and planar type, it is expected that the technique in this paper can be widely used for low phase noise oscillators for both MIC and MMIC applications.