• Land and Housing Review
• /
• v.13 no.3
• /
• pp.125-140
• /
• 2022

Road Deposited Sediment (RDS) is the solids formed from the wear of road, wear of vehicles, exhausts, and the input of the emissions from various sources out of the roads. RDS is seriously polluted by organic matter, nutrients, and metals. RDS plays an important role as the sink and the transport medium of the associated pollutants because RDS can be carried to the adjacent water system via stormwater runoff. In this regard, the heavy metals in RDS were investigated based on the publications. The contents of the metals in RDS were highly variable. The concentration of Cr, Ni, Cu, Fe, Zn, As, Cd, and Pb in urban RDS in various regions was in a range of 3.16-3,410, 1.15-1,382, 20.2-9,069, 2,980-124,853, 81-2,550, 2.3-214, 0.19-21.3, and 15.21-1,125 mg/kg, respectively. The anthropogenic enrichment of the metals in RDS was confirmed by the high concentration of Cu, Zn, Cd, and Pb. The contents of the metals were higher in industrial and traffic areas than in residential areas, while they were generally increased with decreasing particle size. It is believed that this study's results would contribute to quantifying the metals' load via RDS and establishing control strategies.

• Tribology and Lubricants
• /
• v.39 no.2
• /
• pp.49-55
• /
• 2023

Currently, the demand for green technologies toward a sustainable future is rapidly increasing due to growing concern over environmental issues. Methanol is biodegradable and can provide clean combustion to reduce sulfur oxide and nitrogen oxide emissions, and therefore it is a candidate fuel for marine engines. However, the effect of methanol on tribological characteristic degradation should be addressed for methanol-fueled engines. In this study, the methanol addition effects on tribological characteristic degradation is experimentally assessed using a pin-on-disk tribo-tester. Ni-based alloy is used as a target material due to its broad applicability as an engine component material. For a lubricant, engine oil with and without methanol are used. The tests are conducted for up to 10,000 cycles under boundary lubrication while the change in friction force is monitored. Additionally, the wear rate is determined based on laser scanning confocal microscope data. An additional test in which methanol is added at regular intervals is performed with an aim to directly observe its effect on friction. Overall, the friction coefficient increases slightly with increasing methanol concentration. Furthermore, the wear rate of the pin and disk increase significantly with methanol addition. The results also indicate that the friction increases instantaneously with methanol addition at the contacting interface. These findings may be useful for better understanding the methanol effect on the tribological characteristics of Ni-based alloys for methanol-fueled engines with improved performance.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.3
• /
• pp.283-290
• /
• 2024

Currently, the quality standards for recycled aggregates in Korea are very high, at almost the same level as natural aggregates, so recycled aggregates cannot be widely used for concrete. In particular, it is necessary to evaluate how the moisture conditions and curing conditions of recycled aggregates with high absorption rates and wearing rates affect the compressive strength of concrete. Therefore, in this study, we wanted to investigate the effects on compressive strength through experiments using the moisture conditions and curing conditions of recycled coarse aggregate as variables, and compare the compressive strength characteristics of natural coarse aggregate concrete. As a result of this experimental study, the effect of compressive strength on concrete using recycled coarse aggregates according to curing conditions was similar to that of natural aggregate concrete, and the compressive strength showed a low strength of about 13 to 17 %. The effect of the moisture conditions of recycled coarse aggregates was that in the case of wet curing, concrete using wet aggregate showed slightly higher compressive strength than concrete using dry aggregate, but in the case of air curing, on the contrary, dry recycled aggregate concrete was relatively higher than wet aggregate concrete.

• Economic and Environmental Geology
• /
• v.45 no.5
• /
• pp.487-502
• /
• 2012

This paper is focused on mineral compositions, microstructures and distributional characters of remained grains in the fault rocks collected from a fault developed in Yongdang-ri, Yangbuk-myeon, Gyeongju City, Korea, using X-ray diffraction (XRD), optical microscope, laser grain size analysis and fractal dimension analysis methods. The exposed fault core zone is about 1.5 meter thick. On the average, the breccia zone is 1.2 meter and the gouge zone is 20cm thick, respectively. XRD results show that the breccia zone consists predominantly of rock-forming minerals including quartz and feldspar, but the gouge zone consists of abundant clay minerals such as chlorite, illite and kaolinite. Mineral vein, pyrite and altered minerals commonly observed in the fault rock support evidence of fault activity associated with hydrothermal alteration. Fractal dimensions based on box counting, image analysis and laser particle analysis suggest that mineral grains in the fault rock underwent fracturing process as well as abrasion that gave rise to diminution of grains during the fault activity. Fractal dimensions(D-values) calculated by three methods gradually increase from the breccia zone to the gouge zone which has commonly high D-values. There are no noticeable changes in D-values in the gouge zone with trend being constant. It means that the bulk-crushing process of mineral grains in the breccia zone was predominant, whereas abrasion of mineral grains in the gouge zone took place by continuous fault activity. It means that the bulk-crushing process of mineral grains in the breccia zone was predominant, whereas abrasion of mineral grains in the gouge zone took place by continuous fault activity. Mineral compositions in the fault zone and peculiar trends in grain distribution indicate that multiple fault activity had a considerable influence on the evolution of fault zones, together with hydrothermal alteration. Meanwhile, fractal dimension values(D) in the fault rock should be used with caution because there is possibility that different values are unexpectedly obtained depending on the measurement methods available even in the same sample.

• Journal of the Korean Regional Science Association
• /
• v.34 no.2
• /
• pp.3-19
• /
• 2018

The objective of this study is to observe the efficiency of clinical performance on the supply and demand of medical resources in Korea. For the empirical analysis, we constructed the dataset on age standardized mortality rate, the number of physician, specialist, surgery, medical institution, ratio of general hospitals of 16 provinces in Korea from 2006 to 2013. The panel probability frontier model is employed as an analysis method and considered heteroscedasticity and autocorrelation of the error in panel data. In addition, the demographic and socioeconomic characteristics of the 16 provinces, unemployment rate, elderly population ratio, GRDP per capita, and ratio of hospitals in comparison to the general hospitals are used to find the effect on the technical efficiency of clinical performance on supply and demand of medical resources. The results are as follows. First, for the clinical performance, the supply side of human resources such as doctors and specialists and the demand side factors such as chronic illness clinic per unit population have a significant influence, respectively. Second, the technical efficiency of clinical performance on the supply and demand of medical resources of each input component was 59-70% in terms of clinical efficiency in each region. Third. estimates of technical efficiency of inputs that affect clinical performance showed a slight increase in all regions during the analysis period, but the increase trend decreased slightly. Fourth, the ratio of the elderly population and GRDP per capita have a positive influence on the technical efficiency of clinical performance on the supply and demand of medical resources. The difference of each efficiency by region is due to the regional differences of the input medical resources and the combination of them and the demographic and socioeconomic characteristics of the region. It is understood that the differences in technological efficiency due to the complexity of supply and demand of medical resources, demographic structure and economic difference affecting clinical performance by region are different.

• The Korean Journal of Pesticide Science
• /
• v.11 no.3
• /
• pp.201-209
• /
• 2007

Characteristics of the 5 biopesticides that included Bacillus thuringiensis and on the domestic markets were investigated. These products were contained different strains of B. thuringiensis, for examples; product A and E was B. thuringiensis subsp aizawai; product B was B. thuringiensis; product C was B. thuringiensis Berline var. kurstaki; product D was B. thuringiensis var. kurstaki. Number of active spores were counted because they could influence the bio-activity against target pests. Only product C are contained the fixed quantity as its label, however, product D and E were a tenth part, and product A and B were a hundredth part of their descriptions. The pHs of product A and B were measured 3.67 and 3.73, and C, D and E were 5, respectively. Typical bypyramidal crystals produced from B. thuringiensis was found in only product C under a phase contrast microscope. For the uniform formulation of products that conformed whether B. thuringiensis were equally spreaded on the crops, B. thuringiensis in the C, D and E were equally grown on the nutrient agar medium As a results, product A were more different from product C than any other products. When product A and C were bioassayed against different larval stages of diamondback moth, their mortalities with spraying application were showed 100% after 48 hours.

• The Journal of the Petrological Society of Korea
• /
• v.28 no.3
• /
• pp.157-169
• /
• 2019

Pseudotachylytes, produced by frictional heating during seismic slip, provide information that is critical to understanding the physics of earthquakes. We report the results of occurrence, structural characteristics, scanning electron microscopic observation and geochemical analysis of pseudotachylytes, which is presumed to have formed after the Late Cretaceous in outcrops of the Paleoproterozoic granitic gneiss on the Bulil waterfall of the Jirisan area, Yeongnam massif, Korea. Fault rocks, which are the products of brittle deformation under the same shear stress regime in the study area, are classified as pseudotachylyte and foliated cataclasite. The occurrences of pseudotachylyte identified on the basis of thickness and morphology are fault vein-type and injection vein-type pseudotachylyte. A number of fault vein-type pseudotachylytes occur as thin (as thick as 2 cm) layers generated on the fault plane, and are cutting general foliation and sheared foliation developed in granitic gneiss. Smaller injection vein-type pseudotachylytes are found along the fault vein-type pseudotachylytes, and appear in a variety of shapes based on field occurrence and vein geometry. At a first glance fault vein-type seudotachylyte looks like a mafic vein, but it has a chemical composition almost identical to the wall rock of granitic gneiss. Also, it has many subrounded clasts which consist predominantly of quartz, feldspar, biotite and secondary minerals including clay minerals, calcite and glassy materials. Embayed clasts, phenocryst with reaction rim, oxide droplets, amygdules, and flow structures are also observed. All of these evidences indicate the pseudotachylyte formed due to frictional melting of the wall rock minerals during fault slip related to strong seismic faulting events in the shallow depth of low temperature-low pressure. Further studies will be conducted to determine the age and mechanical aspect of the pseudotachylyte formation.

• Economic and Environmental Geology
• /
• v.49 no.6
• /
• pp.417-432
• /
• 2016

It was firstly revealed in this research that the marine terrace of the Ijin-ri (Bukpyung-myeon, Haenam-gun) was formed during the last interglacial (Marine Isotope Stage 5e; MIS 5e). The marine terrace totally ranging from 4.8 m (asl) to 8.8 m (asl) is subdivided into 4 units; Unit I ranges 4.8-5.3 m, unit II ranges 5.3-6.9 m, unit III ranges 6.9-8.3 m, and unit IV ranges 8.3-8.8 m. Strong evidences that units II and III were formed during MIS5e were obtained based on OSL dating, the physical characterizations such as particle size distribution, magnetic susceptibility and water content, principal element and trace element analyses, and quantitative clay mineral analysis for samples at the 30 cm intervals. The rounded gravels on the marine terrace are regarded to be originated from the clastic materials transported directly from the surrounding mountains toward the marine and abraded in the coastal area, without any fluvial processes. During the warmest period (125k, unit II), the increase in rainfall, along with the rapid rise in sea level, was likely caused the high amount of clastic materials transported to the upper part of the beach. As a result of comparing clay mineral ratios of study site with those derived from sediments of either tidal flats, or the Yellow Sea, it is interpreted that the sediments of study site were influenced from the marine. The results will be used to investigate the hydrological activity and sedimentary environment during the high sea level in the past.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.229-237
• /
• 2012

Phosphorus was incorporated into Co/$Al_2O_3$ catalyst for FTS by impregnating an acidic precursor, phosphoric acid, in ${\gamma}-Al_2O_3$ support to improve the mechanical strength, the hydrothermal stability of the catalyst particle, and the catalytic performance as well. Surface characterization techniques such as FT-IR revealed that $AlPO_4$ phase was generated on the surface of the P-modified catalyst. The addition of phosphorus was found to alleviate the interaction between cobalt and alumina surface, and to increase reducibility of catalyst. The catalytic activity such as $C_{5+}$ productivity and turnover frequency (TOF) was calculated to evaluate catalytic performance. The influence of calcination temperature of the $Al_2O_3$ containing 2 wt.% P on the catalytic performance was also investigated. Through hydrothermal stability test and XRD analysis, the P-modified catalyst had strong resistant to the pressurized and hot $H_2O$. The mechanical strength of the P-modified catalyst was also examined through an in-house fluidized-bed vessel, and it was found that the catalyst fragmentation could be successfully suppressed with P. Taken as a whole, the best performance was shown to be at 1~2 wt.% P in alumina and at the calcination temperature of $500^{\circ}C$.

• Clean Technology
• /
• v.27 no.4
• /
• pp.332-340
• /
• 2021

With the recent reinforcement of emission standards, it is necessary to make efforts to reduce NOx from air pollutant-emitting workplaces. The NOx reduction method mainly used in industrial facilities is selective catalytic reduction (SCR), and the most commercial SCR catalyst is the ceramic honeycomb catalyst. This study was carried out to reduce the NOx emitted from steel plants by applying De-NOx catalyst coated on metallic monolith. The De-NOx catalyst was synthesized through the optimized coating technique, and the coated catalyst was uniformly and strongly adhered onto the surface of the metallic monolith according to the air jet erosion and bending test. Due to the good thermal conductivity of metallic monolith, the De-NOx catalyst coated on metallic monolith showed good De-NOx efficiency at low temperatures (200 ~ 250 ℃). In addition, the optimal amount of catalyst coating on the metallic monolith surface was confirmed for the design of an economical catalyst. Based on these results, the De-NOx catalyst of commercial grade size was tested in a semi-pilot De-NOx performance facility under a simulated gas similar to the exhaust gas emitted from a steel plant. Even at a low temperature (200 ℃), it showed excellent performance satisfying the emission standard (less than 60 ppm). Therefore, the De-NOx catalyst coated metallic monolith has good physical and chemical properties and showed a good De-NOx efficiency even with the minimum amount of catalyst. Additionally, it was possible to compact and downsize the SCR reactor through the application of a high-density cell. Therefore, we suggest that the proposed De-NOx catalyst coated metallic monolith may be a good alternative De-NOx catalyst for industrial uses such as steel plants, thermal power plants, incineration plants ships, and construction machinery.