• Progress in Superconductivity
• /
• v.13 no.1
• /
• pp.7-11
• /
• 2011

The effects of Sm:Ba:Cu composition ratio in SmBCO coated conductor on their superconducting properties were investigated. The SmBCO coated conductors were fabricated by reactive co-evaporation method using EDDC(Evaporation using Drum in Dual Chamber) system. In this system, we could obtain various samples with different composition ratios in a batch by the technique providing composition gradient at deposition zone. From the specimens prepared by EDDC system, we found that composition ratio is uniform parallel to the drum axis, but gradient along the circumferential direction of the drum. We installed a shield having parallelogram open area between the deposition chamber and the evaporation chamber in EDDC system, and attached a 30 cm long template, which is parallel to drum axis, onto the drum surface. In this configuration, we could obtain SmBCO coated conductors having a gradient composition along the length of template. We measured the composition ratios and surface morphologies with periodic interval by SEM and EDAX, and confirmed the profile of composition ratio. We also measured critical current using non-contact Hall probe critical current measurement system and thereby could plot composition ratio vs. critical current. The maximum critical current was obtained, and the surface morphology with the shape of roof tile was observed at the corresponding composition ratio of Sm:Ba:Cu = 1.01:1.99:4.87. It was also found that composition ratio had an effect on not only critical current but also surface morphology.

• The Journal of the Acoustical Society of Korea
• /
• v.15 no.6
• /
• pp.81-89
• /
• 1996

It is very important for ultrasonic test method to evaluate the integrity of the class I components in nuclear power plants. However, as the rltrasonic test is affected by internal structures and configurations of test materials, backscattering, that is, time invariant noise is generated in large grain size materials. Due to the above reason, the received signal results in low signal to noise(S/N) ratio. Split spectrum processing(SSP) technique is effective to suppress the grain noise. The conventional SSP technique. however, has been applied to unique algorithm. This paper shows that MPO(minimization and polarity threshold) algorithm which two algorithms are applied simulatancously, was utilized, the signal processing time was shorten by using the new constant-Q SSP with the FIR filter which frequency to bandwidth ratio is constant and the optimum parameters were analysed for the signal processing to longitudinal wave and shear wave with the same requirements of inspection on nuclear power plant site. Moreover, the new ultrasonic test instrument, the reference block of the same product form and material specification, stainless stell test specimens and copper test specimens block of the same fabricated for the application of new SSP technique. As the result of experimental test with new ultrasonic test instrument and test specimens, the signal to noise ratio was improved by appying the new SSP technique.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.37-40
• /
• 1998

Fe량을 0 - 0.4 wt.%까지 변화시켜 Zr-Fe 이원계 합금을 진공아크용해로 제조한 후 1050 $^{\circ}C$에서 30분 균질화 처리 및 700 $^{\circ}C$에서의 열간압연, 그리고 2회의 걸친 냉간압연 및 열처리를 통하여 판재로 제조되었다. 중간 열처리 시 열처리 온도 및 시간을 조절하여 최종 냉간가공에 앞서 각 시편의 결정립 크기 및 경도 값이 같도록 조절하였다. 최종 냉간가공 시 냉간가공량을 60%로 동일하게 조절하였고, 최종열처리 시 열처리 온도 및 시간을 300-750 $^{\circ}C$, 5-3000분으로 각각 변화시켰다. 재결정 정도는 미세조직 관찰 및 경도 측정으로 평가되었으며, 석출물의 구조, 분포 및 형상 등도 TEM으로 분석되었다. 0.1 wt.% 정도까지의 Fe 첨가는 Fe를 첨가하지 않은 순수지르코늄에 비하여 지르코늄입자의 빠른 성장을 야기해, 조대한 재결정 지르코늄 입자들이 나타났다. 그러나 Fe 첨가량이 0.1wt.%이상 첨가되면, Zr$_3$Fe 석출물에 의한 입자성장 억제효과로 지르코늄 입자의 크기는 오히려 작아졌다. 결론적으로, Fe의 첨가는 지르코늄의 확산을 가속시켰다는 것을 보여준다. 한편, 750 $^{\circ}C$에서 열처리 시 이차 재결정현상으로 지르코늄 입자가 비정상적으로 매우 커졌으며, 동시에 annealing twining 현상이 관찰되었다. 이러한 annealing twining 현상은, 입자성장속도가 임계치 이상으로 갑자기 커진, Zr$_3$Fe 석출물이 거의 없는 합금에서만 나타났다. 이 결과를 토대로 annealing twining 현상은 입자의 빠른 이동이 필요 조건이라는 결론을 도출하였다. .Ar-4vol.%H$_2$ 분위기보다 H$_2$분위기에서 소결했을 때 밀도가 더 높았다. 그러나, 결정립은 $UO_2$와 $UO_2$-Li$_2$O의 경우, 수소분위기에서 소결했을 때, (U,Ce)O$_2$와 (U,Ce)O$_2$-Li$_2$O에서는 Ar-4vol.%H$_2$분위기에서 소결했을 때 더욱 성장하였다.설명해 줄 수 있다. 넷째, 불규칙적이며 종잡기 힘들고 단편적인 것으로만 보이던 중간언어도 일정한 체계 속에서 변화한다는 사실을 알 수 있다. 다섯째, 종전의 오류 분석에서는 지나치게 모국어의 영향만 강조하고 다른 요인들에 대해서는 다분히 추상적인 언급으로 끝났지만 이 분석을 통 해서 배경어, 목표어, 특히 중간규칙의 역할이 괄목할 만한 것임을 가시적으로 관찰할 수 있 다. 이와 같은 오류분석 방법은 학습자의 모국어 및 관련 외국어의 음운규칙만 알면 어느 학습대상 외국어에라도 적용할 수 있는 보편성을 지니는 것으로 사료된다.없다. 그렇다면 겹의문사를 [-wh]의리를 지 닌 의문사의 병렬로 분석할 수 없다. 예를 들어 누구누구를 [주구-이-ν가] [누구누구-이- ν가]로부터 생성되었다고 볼 수 없다. 그러므로 [-wh] 겹의문사는 복수 의미를 지닐 수 없 다. 그러면 단수 의미는 어떻게 생성되는가\ulcorner 본 논문에서는 표면적 형태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지니지 않은 단순한 단어(minimal $X^{0}$ elements)로 가정한다. 즉, [+wh] 의미의 겹의문사는 동일한 구성요 소를 지닌 병렬적 합성어

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.43-43
• /
• 2009

단련용 다결정 Ni기 초내열합금은 우수한 가공성, 내산화성, 고온특성 등으로 가스터빈 연소기, 디스크, 증기발생기 전열관 등 발전용 고온부품 소재에 널리 적용되고 있다. 최근 발전설비의 고효율화를 꾀하기 위해 작동 온도를 현격히 증가시키는 기술방향으로 발전하고 있고, 소재측면에서는 기존의 초내열합금 대비 고기능성을 확보할 수 있는 차세대 Ni기 초내열합금 개발이 유럽, 미국, 일본, 중국 등을 중심으로 활발히 이루어지고 있다. 이러한 소재의 고온강도 (온도수용성)를 향상시키기 위해서는 통상 규칙격자 금속간화합물인 $Ni_3(Al,Ti)-{\gamma}'$상의 분율을 증가시킬 수 있지만, ${\gamma}'$상분율이 증가할 경우 용접 및 후열처리 동안 용접열영향부 (HAZ)에서 액화균열이 발생할 가능성이 높아진다. 결정립계를 따라 발생하는 HAZ 액화균열은 입계특성에 의해 크게 영향을 받을 것으로 판단된다. 한편, 본 연구자들은 최근 입계 serration 현상을 단련용 합금에 도입시키는 특별한 열처리를 이론적 접근법을 통해 개발하였다. 형성된 파형입계는 결정학적인 관점에서 조밀 {111} 입계면을 갖도록 분해 (dissociation)되어 낮은 계면에너지를 갖게 됨을 확인하였으며, 입계형상 변화뿐만 아니라 탄화물 특성변화까지 유도하여 크리프 수명을 기존대비 약 40% 정도 향상시킴을 확인하였다. 이러한 직선형 입계 대비 'special boundary'로 간주되는 파형입계가 도입될 경우, HAZ 결정립크기 변화 및 액화거동에 미치는 영향을 고찰하고, 아울러 입계특성 제어가 용접성/용접부 품질 향상에 기여할 수 있는 가능성도 토의하고자 하였다. 본 연구에서는 재현 HAZ 열사이클 시험을 통해 미세구조를 정량적으로 비교하였다. 상대적으로 입계구조가 안정된 파형입계의 이동속도가 高계면 에너지를 갖는 직선형 입계보다 느려 HAZ 결정립 성장이 효과적으로 억제됨을 확인할 수 있었다. 입계 액화거동을 살펴보면, 두 시편 모두 $M_{23}C_6$, MC 등 입계탄화물 계면이 빠른 승온중 액화반응 (constitutional liquation)에 의해 입계가 액화되었으며, 이후 급냉에 의해 입계에 액상막이 존재한 흔적이 발견되었다. 최고온도별로 입계액화 폭/비율을 정량적으로 비교한 결과, 파형입계가 직선입계 대비 대체로 낮음을 확인할 수 있었으며, 때때로 액화되지 않고 잔존하는 입계 탄화물이 관찰되었다. 재현 HAZ 미세조직을 통해 Hot ductility 시험 결과를 유추하자면, 파형입계가 직선입계 보다 좁은 취성온도영역 (Brittle Temperature Range)을 나타낼 것으로 예상되어, 입계특성제어에 의해 Ni기 초내열합금의 용접성을 향상 가능성을 확인하였다.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.2
• /
• pp.74-82
• /
• 2012

Proton exchange membrane fuel cell performance is changed by the complicated physical phenomenon. In this study, water discharge performance of proton exchange membrane fuel cell were performed numerically to compare serpentine channel flow fields of 5-pass 4-turn serpentine and 25 $cm^2$ reaction surface between with and without sub-channel at the rib. Through the supplement of sub channel flow field, it is shown from the results that water removal characteristic inside channel improves because the flow direction of under-rib convection is changed into the sub channel. Reacting gases supplied from entrance disperse into sub channel flow field and electrochemical reaction occurs uniformly over the reaction surface. The results obtained that total current density distributions become uniform because residence time of reacting gases traveling to sub-channel flow field is longer than to main channel.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2037-2047
• /
• 1991

Strength is not simply a single given value but rather is a statistical one with certain distribution functions. This is because it is affected by many unknown factors such as size, shape, stress distribution, and combined stresses. In this study, a model of loss probability is proposed in view of the fact that one of the fundamental configuration of nature is hexagonal, for example, the shapes of lattice unit, grain, and so on. The model sues the concept of loss of certain element in place of Jayatilaka-Trustrum's length and angle of cracks. Using this model, the loss probability due to each loss of certain elements is obtained. Then, the maximum principal stress is calculated by the finite element method at the centroid of the elements under the tensile load for the 4,095 models of analysis. Finally, the failure probability of the brittle materials is obtained by multiplying the loss probability by the ratio of the maximum principal stress to theoretical tensile strength. Comparison of the result of the Jayatilaka-Trustrum's model and the proposed model shows that the failure probabilities by the two methods are in good agreement. Further, it is shown that the parametric relationship of semi-crack lengths for various degrees of birittleness can be determined. Therefore, the analysis of the failure probability suing the proposed model is shown to be promising as a new method for the study of the failure probability of birttle materials.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.75-81
• /
• 2011

Dissimilar joining of aluminum 6061-T6 alloy to aluminum 5083-O alloy was performed using friction-stir welding technique. The mechanical properties, hardness, macro- and micro-structure on dissimilar friction-stir-weld aluminium alloy were investigated. Mechanical properties of the weld mainly depend on which Al alloy is placed at the retreating sides of the rotating tool respectively during dissimilar friction-stir weld because the microstructure of stir zone was mainly composed of welded Al alloys of the retreating side. Onion ring pattern was observed like lamella structure stacked by each Al alloy in turn. It apparently results in defect-free weld zone that traverse speed was changed to 124 mm/min under conditions of tool rotation speed like 1250 rpm with 5 mm of tool's prove diameter, 4.5 mm of prove length, 20 mm of shoulder diameter, and $2^{\circ}$ of tilting angle. The 231 MPa of ultimate stress and the 121 MPa of yield point are obtained about the friction-stir-welded Al 6061-T6(AS) to Al 5083-O(RS).

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.319-323
• /
• 2001

In order to investigate the effect of thickness on the properties of ZnO thin films, a series of films having different thickness were deposited on (0001) sapphire by using pulsed laser deposition(PLD). SEM and XRD analyses showed that, as the film thickness increases, the grain size increased and the crystallinity improved. Room-temperature PL spectra also exhibited that the intensities of both ultraviolet and deep level emission Peaks increased as the film thickness increased. Hall measurements at room- temperature revealed that, as the film thickness changes from 400 to 4000 , the carrier concentration of the film showed sharp decrease, which that of thicker film gradually saturated. Therefore, it is concluded that the strain due to the lattice mismatch between substrate and film is fully relaxed around the thickness of 4000 .

• Journal of the Korean Electrochemical Society
• /
• v.3 no.3
• /
• pp.157-161
• /
• 2000

In order to investigate the substrate effect on the electrochemical properties of thin-film electrode, $LiCoO_2$ was deposited onto the alumina, chemically etched-Si and flat-Si substrates. After annealing at $800^{\circ}C$ in $O_2$ for 30min, the film deposited on the alumina consisted of large particles with several cracks, whereas the film deposited on the flat-Si substrate was composed of very small and uniform particles. The films deposited on the flat-Si showed improved electrochemical properties such as peak potential divergence and rate-capability, over those deposited on the alumina and chemically etched-Si substrate, which can be attributed to the differences of the particle size surface morphology, and the electrical resistance of the current collector.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.59-66
• /
• 2020

In this study, the characteristics of ITO thin film was investigated to finding a low cost and highly transparent electrodes for display of mobile communication devices. The ITO film was deposited by DC magnetron sputter. The experimental conditions were changed as follows: 1. ambient pressure changed 1 to 3 mTorr with 1mTorr step, 2. bias electric voltage changed with 10V step. The chamber was pumped out by rotary pump until 10^-3Torr then the diffusion pump was used to lower the pressure of 10^-6Torr. The results shows us the film growth was obvious when the bias voltage was larger than 300V, but the overall thickness tendency was existed: the more voltage is the thicker thickness. At 330V bias voltage condition, the deposition rate was the largest and apparent grain was showed.