• Title/Summary/Keyword: 루트 용접

Search Result 42, Processing Time 0.024 seconds

Development of welding process to rootpass for U-Groove without gap in pipe 1GR butt welding (파이프 1G 회전 맞대기 용접에서 갭 없는 U-그루브의 루트패스 용접공정 개발)

  • Son, Chang-Hui;Kim, Nam-Gyu;Cho, Sang-Myeong
    • Proceedings of the KWS Conference
    • /
    • 2010.05a
    • /
    • pp.40-40
    • /
    • 2010
  • 산업현장에서는 파이프 또는 탱크류의 1GR용접에서 안정적인 이면비드를 가지는 루트패스 용접을 위해 2~3mm의 루트갭을 띄우고 용접봉 또는 필러와이어를 사용하는 TIG용접을 주로 한다. TIG용접은 고품질의 이면비드가 얻어지며, 용접인자의 제어가 쉽다는 장점이 있어 루트패스 용접에 많이 사용되고 있지만, 루트갭을 띄우면 이면비드는 잘 얻어지지만 용착금속량이 많아지게 되어 제작원가가 상승되고, 또한 소모성 와이어를 사용하는 GMAW에 비해 생산성이 낮다. 따라서, 안정적인 이면비드를 가지면서 생산성이 높은 1GR GMAW 루트패스 용접공정의 개발이 요구되지만, 이 경우도 루트갭이 2~3mm로 정해져 있으면 Fit-up공정에서 공수가 많이 필요하므로 근본적으로 루트갭이 없는 그루브에 대한 루트패스 용접이 더 바람직하다. 본 연구에서는 루트면 2.7mm를 가지는 U-그루브의 갭 없는 루트패스 용접에서 안정적인 이면비드가 형성되는 조건을 검토하기 위해 2.7t의 평판에 대하여 경사상진 각을 주고 기초 실험 후, U-그루브 맞대기 용접 실험을 진행하였다. 이 때, 경사상진 각은 용융금속이 중력으로 인해 아크 후방으로 밀리게 되고, 그로 인해 아크가 모재에 직접 닿게 되어 용입이 더 깊게되므로, 이면비드의 형성에 더 유리하다. 두께 2.7t의 연강 시편 2개를 갭 없는 I-그루브 맞대기 이음에서 Ǿ1.2 연강 솔리드 와이어를 사용하여 GMAW용접을 실시하였고, 용접전류, 용접속도, 경사상진 각, 위빙 폭, 위빙 주파수를 변경하여 각 조건에 대한 이면비드를 관찰하였다. 그 결과 경사상진 각 $25^{\circ}$, 전류 200A, 위빙폭 3mm, 위빙주파수 3Hz의 조건에서 안정적인 이면비드를 얻을 수 있었다. 또한, 현장에서 Fit-up중 발생할 수 있는 루트갭의 문제에 대하여 루트갭 1.2mm의 I-그루브 맞대기 용접에서 경사상진 각, 위빙 폭, 위빙 주파수는 갭 없이 실시한 실험에서 얻어진 가장 안정적인 결과를 사용하였고, 용접 전류, 용접 속도를 변경하여 이면비드를 관찰하였다, 그 결과 갭이 없을 때보다 약 80A 낮은 전류 조건인 120A에서 안정적인 이면비드를 얻을 수 있었다. 앞선 실험들을 기초로 하여 U-그루브 맞대기 용접을 실시 하였고, I-그루브 맞대기 용접에서 사용한 조건들과 유사한 용접 전류, 용접 속도에서 안정적인 이면비드를 얻을 수 있었다.

  • PDF

Prevention of Fatigue Failure at Root Region in the Fillet Welded Joint of Steel Bridge (강교량 필렛용접이음부의 루트부 피로파괴 방지)

  • Lim, Cheong Kweon;Park, Moon Ho
    • Journal of Korean Society of Steel Construction
    • /
    • v.12 no.3 s.46
    • /
    • pp.231-238
    • /
    • 2000
  • There was extreme improvement in the processing result of weld toe, but there is possibility that the fatigue failure occurs from the weld root part where the fatigue strength became low relatively. This study did the fatigue test at the cross rib specimens which implemented a partial penetration weld to improve the fatigue strength of the weld root part. As a result of the fatigue test of the partial penetration weld and the fillet weld specimens, almost the same fatigue strength appeared. Because the fatigue failure began from toe, there was not a reinforcement effect in the weld root part by the partial penetration weld. So, it examined fatigue strength at the partial penetration welding specimens which processed toe to stop the fatigue failure of toe part. As a result, there was big fatigue strength improvement from the partial penetration weld than the fillet weld. Therefore, if fatigue crack occurrence can be restrained from toe, it thinks that the fatigue strength of the root part can improve by the partial penetration weld, after all, it thinks that the overall fatigue life can improve.

  • PDF

Distribution of Welding Residual Stresses in T-joint Weld with Root Gap (루트부 갭이 있는 양면 필릿용접 이음부의 용접잔류응력 분포)

  • H.S. Bang;S.H. Kim;Y.P. Kim;C.W. Lee
    • Journal of the Society of Naval Architects of Korea
    • /
    • v.39 no.3
    • /
    • pp.81-88
    • /
    • 2002
  • The root joint in the welding structures are apt to failure by the stress concentration which is occurred by the external force. Therefore, in the safety and reliability of structure, the complete penetration joint welding which are obtained by the groove welding with edge preparation is generally required. Nevertheless, fillet T-joint welding without edge preparation is often carried out in the fields to reduce working time and consumption of welding electrode, however, this process is likely to produce inadequate joint penetration such as root gap. In this paper, the focus of research is to investigate distribution of welding residual stresses in the plate(or flange) and web of T-joint weld, and especially in the near of root gap notch that is due to incomplete joint penetration. For the analysis, we have chosen model of T-joint weld in the cases of single and multi-pass welding with submerged arc welding and analyzed model by using finite element programs considering the heat conduction and thermal elasto-plastic theory.

Control of arc pulse to overcome misalignment and gap variation in root pass welding of pipe butt joint by GMAW (GMAW 초층 이면비드 용접에서 단차와 갭변동 극복을 위한 아크 충격량 제어)

  • Son, Chang-Hui;Kim, Nam-Gyu;Park, Hyo-Hui;Cho, Sang-Myoung
    • Proceedings of the Korean Society of Marine Engineers Conference
    • /
    • 2011.06a
    • /
    • pp.76-76
    • /
    • 2011
  • 선박이나 산업 플랜트에서 파이프 또는 탱크류의 맞대기 용접 시 안정적인 이면비드의 형성은 매우 중요하다. 대부분의 현장에서 파이프 맞대기 초층용접부의 안정적인 이면비드를 형성하기 위해 3mm의 루트갭을 띄우고 루트면이 없는 V-그루브에서 필러를 사용하는 수동 TIG용접을 주로 사용하고 있다. 수동 TIG용접은 고품질의 비드와 우수한 아크안정성, 그리고 용접인자의 제어가 쉽다는 장점이 있다. 그러나 수동 TIG용접은 용접속도가 10cpm정도로 느리기 때문에 GMAW에 비해 생산성이 낮고 작업자의 숙련도에 따라 품질이 변하게 된다. 본 연구에서는 높은 생산성과 기준갭 1.5mm에서 단차의 허용공차를 크게 하기 위해 루트면 3mm를 가지는 U-그루브의 설계를 하였으며, 두꺼운 루트면을 가지는 그루브에서 안정적인 이면비드를 형성시키기 위해 GMAW에서 아크 충격량에 대한 검토를 실시하였다. GMAW의 아크력이 용입에 어떠한 영향을 미치는지 검토하기 위해 수냉되는 동판에 갭을 1.5mm 띄우고 동일한 용착량과 입열량에서 아크력만을 변화시켜 실험하였다. 또한, U-그루브의 루트부를 모델링하여 두께3t의 평판시편을 각각의 갭과 단차 조건에서 실험하였다. 이 때, 기준갭 1.5mm에서 갭에 의해 생기는 단면적을 기준 갭단면적, 갭이 증가함에 따라 증가되는 단면적을 추가 갭단면적, 갭이 감소함에 따라 감소하는 단면적을 감소 갭단면적으로 정의하였다. 용접 중 발생하는 추가, 감소 갭단면적에 대하여 용착량을 50%의 수준으로 증가, 감소 시켰다. 갭에 따라 아크력을 변경하여 실험을 실시하였고 이면비드의 형상을 확인 하였다. 마지막으로 평판 시편의 조건에서 안정적으로 이면비드가 형성된 조건을 pipe U-그루브에 적용하였다. 그 결과 동판에서 용착량과 입열량이 같음에도 불구하고 아크력이 증가함에 따라 용입이 깊어짐을 확인하였다. 또한. 3t 평판시편에서 아크력의 제어를 통해 큰 단차와 갭이 있을 때, 안정적인 이면비드를 얻을 수 있는 조건을 확립하였다. 마지막으로 pipe U-그루브에서 앞선 실험의 용접조건으로 갭과 단차의 변화에 대해 실험을 하였으나, 시험편의 두께차이에 의한 전도 열손실로 인해 이면비드의 형성이 어려웠고, 아크 충격량의 증가를 통해 이러한 문제를 해결하였다.

  • PDF

A Shape Control of Welded Joints to Improve Fatigue Strength (피로강도 향상을 위한 용접이음부의 형상제어에 관한 연구)

  • Kang, Chang Ib;Kook, Seung Kyu;Lee, Dong Uk
    • Journal of Korean Society of Steel Construction
    • /
    • v.16 no.4 s.71
    • /
    • pp.479-492
    • /
    • 2004
  • When U-ribs of steel deck plates are connected at the field, overhead welding should be done with backing strips. Misalignments may occur and lead to eccentric moments as well as high stress concentrations at welded joints. In this study, stress analyses and fatigue tests were carried out. Stress analyses for U-ribs' welded joints with backing strips were performed with different misalignments, root shapes, root gaps, and backing strip sizes. From the stress analyses, the stress concentration factors increased with increasing misalignments and root gaps. With the fixed misalignments and root gaps, the stress concentration factors obtained in the case of the semi-circle root shape were lower than those in the case of the right-angle root shape. It was verified that backing strip sizes have little influence on stress concentration factors. The fatigue tests for U-ribs' welded joints with backing strips indicated that increased misalignments shorten fatigue life drastically and cracks usually initiate at the root of the base metal and are propagated to the weld bead surface. Based on the results of the stress analyses, root-shape control methods were developed to mitigate stress concentration by changing welding condition control, radius curvature, and flank angle.

Effect of Ni content on mechanical properties of deposited weld metal by FCAW (FCAW 용착금속의 기계적 성질에 미치는 Ni 함량의 영향)

  • Nam, Seong-Gil;Jang, Tae-Won;Yun, Dong-Ryeol;Han, Jeong-Seok;Sin, Hye-Seon
    • Proceedings of the KWS Conference
    • /
    • 2005.06a
    • /
    • pp.118-120
    • /
    • 2005
  • 대형구조물 제작 시에는 세라믹백킹재 등 백킹재를 이용한 편면용접법이 많이 채용되고 있다. 이처럼 백가우징이 적용되지 않는 편면용접법으로 용접 시공 시, 표면부에 비해 루트부의 충격성능이 열화되는 경향이 있다. 본 연구에서는 세라믹백킹재를 채용한 편면용접법의 루트부의 저온 충격성능을 확보할 수 있는 용착금속의 Ni 함량에 대해 고찰하고자 한다.

  • PDF

Development of welding process to overcome misalignment in root pass at butt joint TIG welding of Stainless Steel (스테인리스강 TIG 맞대기 용접 루트 패스에서 단차 극복을 위한 공정 개발)

  • Im, Sung-Bin;Ham, Hyo-Sik;Ha, Jong-Moon;Seo, Ji-Suk;Cho, Sang-Myung
    • Proceedings of the KWS Conference
    • /
    • 2009.11a
    • /
    • pp.26-26
    • /
    • 2009
  • TIG 용접은 고품질이고 용접인자의 제어가 쉽고 정확하다는 장점이 있지만, 얕은 용입과 낮은 생산성과 같은 단점이 있다. TIG 오비탈 용접에서는 용입의 한계 때문에 작은 루트면과 넓은 그루브를 가공하여 다층 용접을 하며, 루트패스에서는 파이프 진원도에 의한 핏업 시 단차의 문제가 자주 발생하여 많은 현장에서 루트갭을 만들어 수동 용접하는 실정이다. 따라서 생산성이 낮으며 생산 단가가 높고 용접 품질이 작업자에 따라 다르게 된다. 이러한 문제점을 해결하여 자동 오비탈 용접을 위해 단차를 흡수 할 수 있는 용접 공정 개발이 필요하다. 본 연구의 목적은 TIG 용접에서 단차에 따른 용접성을 검토하여 이를 맞대기 용접에 적용했을 때 균일한 이면비드를 얻는 공정을 개발하는 것이다. 따라서 본 연구는 아래보기 자세에서 단차에 따른 용입 특성을 이면비드 및 단면으로 비교 분석하였다. 단차 없이 아크길이만 1mm, 2mm, 3mm로 변경하여 실험한 결과 아크길이가 짧아질수록 표면비드 폭은 좁아졌고 이면비드 폭은 증가하는 경향을 나타내어 아크길이가 짧아질수록 용융효율이 증가하는 것을 확인하였다. 단차 1mm에서 아크길이 3mm를 제외하고 표면비드 및 이면비드가 미려하였다. 하지만 단차 2mm에서는 아크길이 1mm, 2mm, 3mm 전부 이면비드가 생성되지 않았다. 이는 단차로 인해 아크길이가 증가하여 용융효율이 낮아졌기 때문이라 판단된다. 이면비드가 생성되지 못한 시험편을 백 베벨링(0.5mm, 1.0mm, 1.5mm, 2.0mm)하여 실험한 결과 단차 2mm, 아크길이 1-3mm 백 베벨링 2.0mm 적용한 시험편에서 양호한 이면비드를 얻을 수 있었다.

  • PDF

A Study on the Effects of Root Gap on Mechanical Properties and Microstructure of Weldment (루트간격이 용접부의 기계적 성질과 미세조직에 미치는 영향에 관한 연구)

  • Lee, Won-Kun;Jang, Gyoung-Boc;Kang, Sung-Soo
    • Journal of the Korean Society for Precision Engineering
    • /
    • v.16 no.10
    • /
    • pp.187-193
    • /
    • 1999
  • Dimensional difference by welding deformation is usually occurred at steel bridge manufacturting or multi-pass welding used at joining of thick plates. Be this, root gap out of standard is frequently developed at butt weld joints. For example, although standard root gap below 6mm at butt weld joints of plates under 15mm thickness, maximum 30mm root opening is developed at the weld field. At this case, 24mm parts out of standard is generally built up. But, there are no accumulated data and restriction about this built up welding pars. In this study, therefore, the accumulation of data for built up parts and the verification of the mechanical properties of weld part as root gap is performed. It is included that tensile, bending, impact, hardness test and microstructural review for each welding specimen of 0mm, 6mm, 30mm root opening.

  • PDF

Control of molten pool by physical force of bead former in TIG welding of overhead and inclined-up position (위보기 및 경사상진자세의 TIG용접에서 비드성형기의 물리적 힘에 의한 용융지 제어)

  • Ha, Jong-Moon;Ham, Hyo-Sik;Im, Sung-Bin;Seo, Ji-Suk;Cho, Sang-Myung
    • Proceedings of the KWS Conference
    • /
    • 2009.11a
    • /
    • pp.23-23
    • /
    • 2009
  • 우수한 용접부 품질 때문에 TIG를 이용한 오비탈 용접은 파이프 용접에 널리 사용되고 있다. 하지만 루트갭이 없고 루트페이스가 큰 맞대기 오비탈 용접의 위보기 및 경사상진자세에서는 오목한 이면비드가 형성되기 쉽지만, 이러한 문제를 극복하기 위한 연구는 희박한 실정이다. 본 연구에서는 위보기 및 경사상진자세에서 볼록한 이면비드의 형성을 연구하기위해서 용융지의 제어 방법을 적극적으로 검토하였다. 4mm 두께의 SS400 시편을 위보기 및 경사상진자세에서 각각 Bead-on-plate 용접하고, 이 때 비드성형기의 사용에 따른 비드 형상 변화를 관찰하였다. 텅스텐 전극과 비드 성형기간의 거리(Tip To Former Distance, 이하 TTFD)를 4.5mm에서 7.5mm로 1mm단위로 변경시켜 실험하였으며, TTFD가 증가할수록 위보기 및 경사상진자세에서 이면비드 높이가 감소하였으며 표면비드의 처짐이 증가하였다.

  • PDF