• Prospectives of Industrial Chemistry
• /
• v.22 no.5
• /
• pp.1-13
• /
• 2019

국제해사기구(IMO, international maritime organization)는 2015년부터 배출규제해역(ECA, emission control area)을 운항하는 선박은 황 함유량이 0.1%(m/m) 이하로 강화된 기준을 만족하는 연료를 사용해야 하며, 2020년부터는 모든 선박에 대해 황 함유량이 0.5%(m/m) 이하인 연료를 사용하거나 동등 이상의 성능을 갖는 배출가스 후처리 장치의 설치를 의무화하였다. 이에 따라, 선박에서 배출되는 오염물질을 제어할 수 있는 다양한 기술이 개발되고 있으며, 후처리 관점에서 습식 스크러버(wet scrubber)는 선박의 디젤 엔진에서 배출되는 이산화황(sulfur dioxide)을 저감시키기 위한 가장 적합한 해결책으로 알려져 있다. 습식 스크러버는 해수를 사용하는 개방형 스크러버(open loop scrubber)와 화학세정수를 사용하는 폐쇄형 스크러버(closed loop scrubber)로 구분된다. 습식 스크러버는 오염물질의 효율적인 처리가 가능하지만 유지보수비가 비싸고, 폐수 발생으로 인한 2차 오염발생 및 부식에 매우 취약한 단점이 있다. 따라서 최근에는 스크러버 내부의 부식을 방지하기 위한 내부식성 재질에 관한 연구와 흡수제(absorbent)의 고도화 연구가 활발히 진행되고 있다. 또한, 하이브리드형 스크러버(hybrid scrubber)는 개방형과 폐쇄형 스크러버의 장점을 결합한 기술로 황산화물의 배출을 규제하는 배출규제해역에서는 폐쇄형 스크러버를 가동하고, 선박이 공해상으로 진입할 경우 개방형 스크러버로 전환함에 따라 황산화물 배출 및 반응 후 세척수의 폐수배출 기준을 동시에 만족할 수 있다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.6
• /
• pp.1092-1099
• /
• 2022

Research on exhaust aftertreatment devices to reduce air pollutants and greenhouse gas emissions is being actively conducted. However, in the case of the particulate matters/nitrogen oxides (PM/NOx) simultaneous reduction device for ships, the problem of back pressure on the diesel engine and replacement of the filter carrier is occurring. In this study, for the optimal design of the integrated device that can simultaneously reduce PM/NOx, an appropriate standard was presented by studying the flow inside the device and change in back pressure through the inlet/outlet pressure. Ansys Fluent was used to apply porous media conditions to a diesel particulate filter (DPF) and selective catalytic reduction (SCR) by setting porosity to 30%, 40%, 50%, 60%, and 70%. In addition, the ef ect on back pressure was analyzed by applying the inlet velocity according to the engine load to 7.4 m/s, 10.3 m/s, 13.1 m/s, and 26.2 m/s as boundary conditions. As a result of a computational fluid dynamics analysis, the rate of change for back pressure by changing the inlet velocity was greater than when inlet temperature was changed, and the maximum rate of change was 27.4 mbar. This was evaluated as a suitable device for ships of 1800kW because the back pressure in all boundary conditions did not exceed the classification standard of 68mbar.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.2
• /
• pp.177-182
• /
• 2015

The NOx emissions from diesel engines and industrial boilers are a major cause of environmental pollution. The selective catalytic reduction of urea is an aftertreatment technology that is widely used for the reduction of NOx emissions. The objective of this study was to investigate the characteristics of the thermal decomposition of a urea aqueous solution using laboratory-scale experimental equipment under conditions similar to those of marine diesel engines. A 40 wt. urea aqueous solution was used in this study. It was found that the total conversion rate varied with the inflow gas conditions and flow rates of the urea aqueous solution. In addition, there were conversion rate differences between NH3 and HNCO. At inflow gas temperature conditions of $210^{\circ}C$ and $250^{\circ}C$, the $NH_3$ conversion rate was found to be higher than that of the HNCO, depending on the residence time.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.92-99
• /
• 2011

To measure the traffic pollutants with high temporal and spatial resolution under real conditions, a mobile emission laboratory (MEL) was designed. The equipment of the mini-van provides gas phase measurements of CO, NOx, $CO_2$, THC (Total hydrocarbon) and number density & size distribution measurements of fine and ultra-fine particles by a fast mobility particle sizer (FMPS) and a condensation particle counter (CPC). The inlet sampling port above the bumper enables the chasing of different type of vehicles. This paper introduces the technical details of the MEL and presents data from the car chasing experiment of diesel bus equipped with aftertreatment system. The dilution ratio was calculated by the ratio of ambient NOx and tail-pipe NOx. Most particles from the diesel bus were counted under 300 nm and the peak concentration of the particles was located between 30 and 60 nm. The total PM number emission from diesel bus equipped with DPF was 10 orders of magnitude lower compared to those emitted from base diesel bus. And the total PM number emission from diesel bus equipped with SCR was comparable to the particle emission from base diesel bus.

• Korean Chemical Engineering Research
• /
• v.56 no.2
• /
• pp.281-290
• /
• 2018

As the internal combustion engine vehicles of high fuel efficiency and low emission are demanded, it becomes important to procure technologies for improving low-temperature performance of automotive catalyst systems. In this study, we showed that the combustion rate of diesel particulate matter is greatly enhanced at low temperature by applying fuel-borne catalyst and perovskite catalyst concurrently. It was tried to examine the correlation between elemental composition of perovskite catalyst and combustion activity of mixed catalyst system. To achieve this goal, we applied temperature-programmed oxidation technique in testing the combustion behavior of perovskite-mixed particulate matter bed which contained the element of fuel-borne catalyst or not. We tried to explain the synergetic action of two catalyst components by comparing the trends of concentrations of carbon dioxide and nitrogen oxide in temperature-programmed oxidation results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.3
• /
• pp.20-25
• /
• 2012

As a kind of distributed energy system, the co-generation system based Diesel engine using after-treatment device was devised for its environmental friendly and economic qualities. It is utilized in that the electric power is produced by the generator connected to the Diesel engine, and waste heat is recovered from both the exhaust gases and the engine itself by the finned tube and shell & tube heat exchangers. An after-treatment device composed ceramic heater and DOC(Diesel Oxidation Catalyst) is installed at the engine outlet in order to completely reignite the unburned fuel from the Diesel engine. In this study, mutual relation of each experimental condition was derived through minimum number of experiment using Taguchi Design and ANOVA recently used in the various fields. It is found that the total efficiency (thermal efficiency plus electric power generation efficiency) of this system reaches maximum 94.4% which is approximately higher than that of the typical diesel engine exhaust heat recovery system.

• Journal of the Korean Institute of Gas
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2013

Using natural gas-hydrogen blended fuel (HCNG) in a heavy duty vehicle is regarded as an alternative to meet reinforced emission regulation compared to a recent direct injection (DI) diesel engine. Hydrogen can lead stable lean combustion even under leaner mixture condition than natural gas, so that improving not only thermal efficiency but also $NO_x$ emissions. In the present study, the feasibility of HCNG engine's commercialization was accessed with HCNG fuel (30% $H_2$ and 70% natural gas) in aspect to the reliability and possibility to reduce $NO_x$ emissions by the level of EURO-VI under various operating conditions.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.7
• /
• pp.361-365
• /
• 2007

Aero-pulsation noise, generally caused by geometric asymmetry of a rotating device, is one of considerable sources of annoyance in passenger cars using the turbocharged diesel engine. Main source of this noise is the compressor wheel in the turbocharger system, and can be reduced by after-treatment devices such as silencers, but which may increase the manufacturing cost. More effective solution is to improve the geometric symmetry over all, or to control the quality of components by sorting out inferior ones. The latter is more simple and reasonable than the former in view of manufacturing. Thus, an appropriate discrimination method should be needed to evaluate aero-pulsation noise level at the production line. In this paper, we introduce the accurate method which can measure the noise level of aero-pulsation and also present its evaluation criteria. Besides verifying the reliability of a measurement system - a rig test system-, we analyze the correlation between the results from rig tests and those from vehicle tests. The gage R&R method is carried out to check the repeatability of measurements over 25 samples. From the result, we propose the standard specification which can discriminate inferior products from superior ones on the basis of aero-pulsation noise level.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1108-1119
• /
• 2018

As the interest on the air pollution is gradually rising at home and abroad, automotive and fuel researchers have been studied on the exhaust and greenhouse gas emission reduction from vehicles through a lot of approaches, which consist of new engine design, innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research has brought forward two main issues : exhaust emissions (regulated and non-regulated emissions, PM particle matter) and greenhouse gases of vehicle. Exhaust emissions and greenhouse gases of automotive had many problem such as the cause of ambient pollution, health effects. In order to reduce these emissions, many countries are regulating new exhaust gas test modes. Worldwide harmonized light-duty vehicle test procedure (WLTP) for emission certification has been developed in WP.29 forum in UNECE since 2007. This test procedure was applied to domestic light duty diesel vehicles at the same time as Europe. The air pollutant emissions from light-duty vehicles are regulated by the weight per distance, which the driving cycles can affect the results. Exhaust emissions of vehicle varies substantially based on climate conditions, and driving habits. Extreme outside temperatures tend to increasing the emissions, because more fuel must be used to heat or cool the cabin. Also, high driving speeds increases the emissions because of the energy required to overcome increased drag. Compared with gradual vehicle acceleration, rapid vehicle acceleration increases the emissions. Additional devices (air-conditioner and heater) and road inclines also increases the emissions. In this study, three light-duty vehicles were tested with WLTP, NEDC, and FTP-75, which are used to regulate the emissions of light-duty vehicles, and how much emissions can be affected by different driving cycles. The emissions gas have not shown statistically meaningful difference. The maximum emission gas have been found in low speed phase of WLTP which is mainly caused by cooled engine conditions. The amount of emission gas in cooled engine condition is much different as test vehicles. It means different technical solution requires in this aspect to cope with WLTP driving cycle.