• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.1
• /
• pp.34-41
• /
• 2014

Purpose: In this study, the diameter of each implant driver was measured and compared to find out the compatibility of implant drivers. Materials and methods: Drivers from 12 implant systems being used in Dankook University Dental Hospital were included in this study. The shapes of the implant drivers were segregated, and the effective length and the diameter of upper, middle, lower part of driver tips were measured (n=10). The measured data were mathematically analyzed for its compatibility. Results: A driver with the smallest diameter (1.17 mm) had the highest compatibility at the upper part of driver tip. This driver could be used for a bigger driver up to 1.35 mm in diameter. There were several driver groups which had the same diameter so as to be interchangeable each other. In the middle part, the smallest diameter measured was 1.2 mm and this was able to replace a driver up to 1.40 mm diameter. Since the diameter generally became thicker from upper part (the tip of driver) to the lower part (the shank of driver), some drivers with bigger diameter at the upper part so which was failed to show any compatibility became compatible with a driver which had smaller diameter at the upper part but wider in the middle part. The compatibility of torx shape drivers were affected by the inner diameter of the drivers not only by the outer diameter. Furthermore, the inner diameter of torx drivers decided the compatibility between torx and hex drivers. Conclusion: From the study it was found that compatibility in drivers existed among certain implant systems and to check its compatibility the diameter at a certain effective length should be measured. However, there has been not enough studies about long-term use of compatible drivers, so effects of using compatible drivers on drivers and implants are unknown. Therefore, usage in inevitable cases only is recommended and further study is needed.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.798_799
• /
• 2009

초고속 전동기는 일반적인 회전수를 초고속 전동기로서 기존 전동기보다 여러 가지 장점을 가지고 있어 그 수요가 늘어나고 있는 실정이다. 본 논문에서는 15 [kW], 120,000 [rpm]의 초고속 전동기를 제작하기 위한 기초설계단계에서 계산된 내용과 형상을 알아보고 그 가능성을 타진해 본 내용이다. 본 연구에서는 영구자석을 사용한 초고속 전동기로서 해석과 설계과정을 거치면서 로터의 직경을 계산하고 구동 드라이버설계제작 및 사용할 영구자석과 코어을 제작하여 고소속 전동기를 제작하고 제작된 전동기를 조립하여 그 특성을 평가하는 순서로 개발을 완료하고자 하였다. 본 논문에서는 이러한 내용 중 FEM 설계 과정을 소개하고 그 가능성에 대해서 알아보았다.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.746-747
• /
• 2008

초고속 전동기는 일반적인 회전수를 초고속 전동기로서 기존 전동기보다 여러 가지 장점을 가지고 있어 그 수요가 늘어나고 있는 실정이다. 본 논문에서는 15kW, 120,000rpm의 초고속 전동기를 제작하기 위한 기초설계단계에서 계산된 내용과 형상을 알아보고 그 가능성을 타진해 본 내용이다. 본 연구에서는 영구자석을 사용한 초고속 전동기로서 해석과 설계과정을 거치면서 로터의 직경을 계산하고 구동 드라이버 설계제작 및 사용할 영구자석과 코어을 제작하여 고소속 전동기를 제작하고 제작된 전동기를 조립하여 그 특성을 평가하는 순서로 개발을 완료하고자 하였다. 본 논문에서는 이러한 내용중 FEM 설계 과정을 소개하고 그 가능성에 대해서 알아보았다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.4
• /
• pp.321-327
• /
• 2003

As the continuous casting process is to product slab with high temperature liquid steel, the main role of strand driven roll is to withdraw slab from mold as operator set up casting speed pattern. The strand driven roll in old cast machine is controlled casting speed only. Due to inaccuracies in drive setting up, varying roll diameters, bulging in the product, withdrawal force was distributed irregularly. As a result, because of horizontal crack in slab comer, high casting speed can't be achieved. In this paper, the correlation between the distribution of withdrawal force and slab quality is investigated and the new control algorithm which can be distributed regularly the withdrawal force of strand driven roll is proposed. The principle of proposed algorithm is not to control motor torque directly but to control motor speed reference according to sharing ratio of withdrawal force which is set up in high level controller. The proposed algorithm implemented in POSCO Kwangyang 1-4 continuous casting plant.