• Journal of Conservation Science
• /
• v.30 no.3
• /
• pp.287-298
• /
• 2014

This study investigates the material properties of the traditional bricks used in the royal tomb of King Muryeong. Compressive strengths, thermal conductivities, absorptance and the rate of residual moisture are measured by non-destructive experiments. Compressive strength of the traditional bricks is estimated by using the ultrasonic wave velocity and the absorptance. Based on the experimental results, the predicted compressive strengths using the ultrasonic wave velocity are unsuitable for the traditional bricks due to the rough surface and thickness variation of the specimens. The strengths using the absorptance are more suitable than those using the velocity because the predicted average strengths (28.69 MPa ~ 33.19 MPa) are close to building materials like normal strength concrete. In addition, the methods using the absorptance are not influenced by surface and thickness conditions of the specimens. The average thermal conductivities of the bricks measured by using Mathis TCi are close to those of soils (1.58 W/mK). The absorptance and the rate of residual moisture of the bricks are 1.6 % ~ 15 %, 0 % ~ 0.7 %, respectively.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.1
• /
• pp.47-56
• /
• 2012

As attractive lips are important component of appealing faces, the study was conducted to investigate the association of mouth-breathing and thickness of lower lips in mouth-breathers and nasal-breathers. The subjects were 436 adolescent patients aged 8~18 years who took cephalometrics. The results were as follows. The ratio of lower lip thickness to that of upper lip thickness in mouth breathing and nasal breathing groups were $1.13{\pm}0.14$, $1.02{\pm}0.14$, respectively. According to subjects' skeletal pattern, the ratio in Class I sample was $1.05{\pm}0.09$. Class II subjects showed $1.20{\pm}0.12$, and Class III showed $0.97{\pm}0.11$. Mouth - breathers had higher lower/upper lip ratio than nasal breathers meaning their lower lips were thicker. Skeletal Class II patients group showed the most thickest lower lips among Class I, II, III subgroups.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.3
• /
• pp.64-76
• /
• 2002

기존의 이론적 연구와 실험적 연구를 바탕으로 충돌 제트의 수치 모델을 개발하였다. 본 모델은 like-doublet 충돌제트로부터 생성되는 액적의 모든 특성을 액막이 분열되는 시점에서 결정한다. 액적 특성을 결정하기 위해 이론적 연구로부터 얻어진 액막 두께, 액주의 직경, 액적 크기와 실험적 연구로부터 얻어진 액막/액적 속도, 액막 분열 거리, 분열 주파수, 액적 질량 유량 분포를 이용하였다. 액적의 질량 유량 분포는 Laplace 분포로부터 표준 편차를 이용하여 모사하였다. 또한 실험 결과를 이용하여 액막 분열 거리, 분열 주기, 표준 편차에 대한 경험식을 유도하였다. 개발된 모델은 정성적인 분무 패턴뿐만 아니라 정량적인 SMD 및 질량 유량 분포에서 실험 결과와 잘 일치한다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.4
• /
• pp.427-436
• /
• 2014

The goal of this paper is to estimate proper hardfacing material and thickness of STD61 hot-working tool steel through three-dimensional heat transfer and thermal stress analyses. Stellite6, Stellite21 and 19-9DL superalloys are chosen as alternative hardfacing materials. The influence of hardfacing materials and thicknesses on temperature, thermal stress and thermal strain distributions of the hardfaced part are investigated using the results of the analyses. From the results of the investigation, it has been noted that a hardfacing material with a high conductivity and a thinner hardfaced layer are desired to create an effective hardfacing layer in terms of heat transfer characteristics. In addition, it has been revealed that the deviation of effective stress and principal strain in the vicinity of the joined region are minimized when the Stellite21 hardfaced layer with the thickness of 2 mm is created on the STD61. Based on the above results, a proper hardfacing material and thickness for STD61 tool steel have been estimated.

• Journal of Digital Convergence
• /
• v.17 no.8
• /
• pp.329-336
• /
• 2019

The purpose of this study is to analyze the differences of the lower back pain, fatigue, and Achilles tendon thickness according to wearing and not wearing high heels in order to understand symptoms of musculoskeletal diseases caused by wearing high heels in college students. lower extremity pain fatigue and achilles tendon thickness were measured in high heel wear group (n=19) and non high heels wear group (n=23). Participants' general characteristics and the lower extremity pain, fatigue, and Achilles tendon thickness were analyzed using mean, standard deviation. Differences in lower extremity pain, fatigue, and achilles tendon thickness were analyzed by independent t-test. The results showed that the difference between the participants' lower extremity pain (t=2.28, p=.028), right achilles tendon thickness (t=2.30, p=.027) and left achilles tendon thickness (t= 3.89, p<.001) The results of this study show that convergence approach can be applied as a basis for health problems in the structure and function of musculoskeletal disorders associated with wearing high heels. In the future, follow up observation according to the wearing of high heels in the same subject will be needed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.50-56
• /
• 2011

Injection molding process is one of the popular manufacturing methods to produce plastic parts with high efficiency and low cost. Ball seat for automobile suspension is made by an injection molding process as a part to support pivot function of ball joint consisted of ball stud and housing. It is necessary for a ball seat to have a dimensional stability in the three dimensional inner area to be contacted with ball stud. In this paper, the dimensional stability of inner surface is indirectly analyzed by checking the difference of inner diameter around the circumferential direction and the thickness variation at the top part of ball seat. Measurement was performed by using the coordinate measuring machine and the fixture to hold ball seat. Optimization of injection molding processes such as injection time, cooling time and temperatures of cylinder barrel was derived to reduce the difference of inner diameter and the thickness variation at the top part of ball seat based on the Taguchi method.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.1838-1842
• /
• 2008

본 연구에서는 하구 유입 하천에서 발생하는 염수쐐기의 형상 및 거동특성을 구명하기 위하여 정상상태 염수쐐기 실험을 수행하였다. 길이에 비해 상대적으로 폭이 좁은 개수로의 상류부분에는 담수를 지속적으로 공급할 수 있는 담수공급장치를 설치하였고, 정상상태의 염수쐐기를 발생시키기 위하여 염수수조 측면에 지속적으로 염수를 공급할 수 있는 염수공급수조를 설치하였다. 실험조건은 담수 방류량과 이층류의 밀도차의 영향을 고려한 밀도프루드수(densimetric Froude number)를 기준으로 선정하였다. 실험결과 각 케이스별 염수쐐기의 형상은 중앙부에서 약간의 산포된 양상을 제외하고는 거의 선형을 이루는 것으로 관찰되었다. 경계층의 형상과 두께는 이층류의 농도장을 측정하고 밀도변동성분을 고려한 표준편차를 통하여 산정하였다. 그리고 염수쐐기의 선단부에 해당하는 리차드슨수와 경계층 두께와의 비교 등을 통해서 경계층의 양상을 파악하였다.

• Economic and Environmental Geology
• /
• v.12 no.1
• /
• pp.17-28
• /
• 1979

Geodetic and geophysical quantities related to gravity data are analyzed using three-dimensional sin x/x method for the southern part of the Korean peninsula and adjacent Japan Sea. The thickness of isostatic crust is found as 26 km. The average isostatic gravity anomaly in this area is appeared to be +24.8 mgal, of which result indicates that the surface features are under-compensation or the thickness of the crust is thinner than normal. It is noteworthy that the general trend of the deflections of the vertical in direction is nearly perpendicular to the geological structure having a direction of NNE-SSW in the southern part of Korea.

• Journal of the Korean Ceramic Society
• /
• v.38 no.5
• /
• pp.485-491
• /
• 2001

일반 산업 및 원자력 관련 산업용 구조소재의 표면특성 향상을 위해 저압 화학기상 증착법에 의해 15~25cm 직경의 흑연기판 위에 고순도의 치밀한 SiC 증착층을 제조하였다. 미세구조와 두께가 균일한 증착층을 얻기 위하여 증착온도의 균일성, 반응가스 고갈효과, 가스 흐름 형태 등의 영향을 고려하였다. 이중에서 반응 용기내의 가스 흐름 형태가 증착층의 균일도에 가장 큰 영향을 주는 것으로 판단되었으며 가스 주입구의 위치와 크기를 조정함으로써 25cm의 직경을 갖는 흑연 기판에 두께 편차가 $\pm$12% 이내인 SiC 증착막을 제조할 수 있었다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.6
• /
• pp.1401-1406
• /
• 2014

Knowledge of the manufacturing process of semiconductor devices in order to obtain a copper pattern using chemical mechanical polishing (CMP) planarization using a Wafer polishing process is applied with a thickness of the copper measured in real time, which need to be precisely controlled by, where the acquisition the actual thickness of the sensor value with the calculated value in terms of error can occur in the process. Approximated the actual measurement values so as to obtain a method using a simple average, moving average, compared to the results using filters onggo Strom real-time measurements of the thickness of the units of the control system to reduce the variation in the implementation of the method described for the.