• The Journal of the Korea Contents Association
• /
• v.11 no.10
• /
• pp.293-300
• /
• 2011

This study was to find out the effect of cervical and thoracic stretching and strengthening exercise program on forward head posture. 32 adults had forward head posture were selected as the subjects for the study. The training program of the exercise group(n=16) consist of postural education with exercise program, subjects in the control group(n=16) participated in a postural education only. Postural measurements of Craniovertebral Angle(CVA) and Cranial Rotation Angle(CRA) were obtained from the using x-ray and PACS(Picture Archiving and Communications System) ${\pi}view^{TM}$. The results were compared with change of CVA and CRA exercise group were significant(p<.05) compared to the control group. However CRA of contol group was significant(P<.05). Also, there were no significant difference(p>.05) between groups on any pre-test measure. however there were significant difference(p<.05) between groups on CVA and CRA post-test measure. This study showed that cervical and thoracic stretching and strengthening exercise program can improve spinal posture alignment for decreasing forward head posture in subjects. These results can be fundamental data for further development of exercise program in interventions of postural improvement.

• The korean journal of orthodontics
• /
• v.25 no.2 s.49
• /
• pp.129-142
• /
• 1995

The purpose of this study was to estimate correlations of craniocervical posture and craniofacial morphology in Korean young adults. The sample consisted of 50 young adults (25 males and 25 females) who had good profile and Class I molar relationship. The analysis of craniocervical posture and craniofacial morphology was performed on lateral cephalograms taken in natural head position. The results were as follows, 1. The mean and the standard deviation of postural and morphologic variables were obtained. 2. Korean young adult had cervical lordosis of which degree between OPT and CVT shows $3.55{\pm}2.58^{\circ}$ 3. Craniocervical posture and each of vertical ratio, facial prognathism, mandibular rotation showed high correlation. 4. Correlation coefficients between postural variables and each of intermaxillary relation, anteroposterior ratio were low. 5. The head positioning error of natural head position was smaller than the inter-individual variability of postural variables.

• Journal of Convergence for Information Technology
• /
• v.7 no.2
• /
• pp.59-65
• /
• 2017

In order to realize the operation of the creative modular toy, it is required to record the motion and to read and repeat the motion. At this time, a control potentiometer is used to read the absolute angle of rotation of the toy motion output shaft. However, the unstable part of the sensing area of the potentiometer is present in a certain region, which may lead to instability of the motor control. In this paper, we propose an algorithm to find the absolute angle of one rotation by reading two stable potentiometers on one axis and reading each stable region. We also describe the correction algorithm that is needed to perform multiple rotations. The proposed method is applied to Topobo modular toys to record the operation and perform iterative operation. In addition, multi-turn operation is recorded and operated to suggest the usefulness of the proposed method. In the future, we will expand the functions of recording and playback through various actions.

• The korean journal of orthodontics
• /
• v.22 no.3 s.38
• /
• pp.491-507
• /
• 1992

Biennial serial cephalometric radiographs of 47 children (26 boys, 21 girls) were used to analyze the craniofacial growth changes in Korean children from 8 years to 16 years of age. A craniofacial model was designed for this study. It consisted of 72 anatomical points and 98 derived points. The craniofacial changes of these samples during these ages might be summarized as follows: 1. Mandibular growth to cranial base was more forward than maxillary growth. 2. Mandibular growth during this period was found to be a forward-upward (bite closing) rotation of the mandible. 3. Growth changes in total mandibular length (Ar-Gn) showed a pubertal growth spurt at 12-14 years of age in boys and 10-12 years of age in girls. Synchrony of the growth spurts on total mandibular length (Ar-Gn) and standing body height was found. 4. The pubertal spurts occured in the growth of total cranial base (Ba-Na) at 10-12 years of age in boys and 8-10 years of age in girls. The time of the spurts of the cranial base growth was 2 years ahead of that of the total mandibular growth. 5. Synchrony of growth spurts in anterior facial height (Na-Me), posterior facial height (S-Go) and body height was found. 6. The whole craniofacial changes during this period were plotted by using a X-Y plotter and personal computer. A simple profilogram for an diagnostic tool was obtained.

• Radiation Oncology Journal
• /
• v.14 no.2
• /
• pp.149-158
• /
• 1996

Purpose : To get an accute steepness of dose gradients at outside the target volume in intracranial lesion and a less limitation of beam selection avoiding the high dose at normal brain tissue, this Photon Knife Radiosurgery System was developed in order to provide the three-dimensional dose distribution through the reconstruction of CT scan and the combined stereotactic trans-multiarc beam mode based on linear accelerator photon beam. Materials and methods : This stereotactic radiosurgery, Photon Knife based on linear accelerator photon beam was provided the non-coplanar multiarc and trans-multiarc irradiations. The stereotactic trans-multiarc beam mode can be obtained from the patient position in decubitus. This study has provided the 3-dimensional isodose curve and anatomical structures with the surface rendering technique. The dose distribution from the combined two trans-multiarcs (2M 2TM) was compared to that of four non-coplanar multiarcs (4M) with same collimator size of 25 mm in a diameter and total gantry movements. Results : In this study, it shows that the dose distributions of stereotactic beam mode are significantly depended on the selected couch and gantry angle in same collimator size. Practical dose distribution of combined stereotactic trans-multiarc beam has shown a more small rim thickness than that of the non-coplanar multiarc beam mode in axial, sagittal and coronal plane in our study. 3-Dimensional dose line displayed with surface rendering of irregular target shape is helpful to determine the target dose and to predict the prognosis in follow-up radiosurgery. Conclusions : 3-Dimensional dose line displayed with surface rendering of irregular target shape is essential in stereotactic radiosurgery. This combined stereotactic trans-multiarc beam has shown a less limitation of the selection couch and gantry beam angles for the target surrounding critical organs. It has shown that the dose distribution of combined trans-multiarc beam greatly depended on the couch and gantry angles. In our experiments, the absorbed dose has been decreased to $27%$ / mm in maximum at the interval of $50\%$ to $80\%$ of isodose line.

• Korean Journal of Optics and Photonics
• /
• v.25 no.1
• /
• pp.29-37
• /
• 2014

We have studied and demonstrated general, systematic error-correction methods for a dual rotating quarter-wave plate ellipsometer. To estimate and correct 5 systematic error sources (three offset angles and two unexpected retarder phase delays), we used 11 of the 25 Fourier components of the ellipsometry signal obtained in the absence of an optical sample. Using these 11 Fourier components, we can determine the errors from the 5 sources with nonlinear optimization methods. We found systematic errors ${\epsilon}_3$, ${\epsilon}_4$, ${\epsilon}_5$) are more sensitive to the inverted Mueller matrix than retarder phase delay errors (${\epsilon}_1$, ${\epsilon}_2$) because of their small condition numbers. To correct these systematic errors we have found that error of any variety must be less than 0.05 rad. Finally, we can use the magnitudes of these errors to correct the Mueller matrix of optical components. From our experimental ellipsometry signals, we can measure phase delay and the rotational angular position of its fast axis for a half-wave plate.

• The korean journal of orthodontics
• /
• v.34 no.1 s.102
• /
• pp.13-21
• /
• 2004

Recently several techniques have been reported for the treatment of anterior open bite in adults characterized by molar intrusion with skeletal anchorage. In this study, five adult patients who had anterior open bite malocclusion were selected to undergo upper molar intrusion with midpalatal miniscrew to close the open bite. The aim of this study is (1) to validate true intrusion of molars in adults (2) to test the usefullness of midpalatal miniscrews as anchorage for intruding upper molars (3) to evaluate the skeletal and dental changes of open bite closure. The results are as follows. (1) All had true intrusion of the maxillary molars. Mean amount of molar intrusion was 3.4mm(range 1.5-5mm). (2) No movement of midpalatal miniscrew occurred during their use. (3) Open bite closure was achieved for all 5 patients. The mandible closed and B-point rotated anteriorly and upward. The mandibular plane angle and the occlusal plane angle decreased.

• The korean journal of orthodontics
• /
• v.36 no.5
• /
• pp.324-330
• /
• 2006

Objective: The purposes of this study were to evaluate the differences between sand blasted, large grit and acid-etched (SLA) treated mini-implants and smooth surface orthodontic mini-implants in relation to the removal torque as well as the histologic analysis. Methods: Custom-made, screw-shaped, titanium implants with a length of 9.5 mm and an outer diameter of 1.8 mm were divided into 2 groups; the SLA group (20 SLA treated orthodontic mini-implants) and the smooth surface group (20 smooth surface mini-implants), and placed In the tibia metaphysis of 10 rabbits. Each rabbit had 4 mini-implants placed, 2 in each tibia. The right tibia were implanted with the SLA group mini-implants and the left tibia had the smooth group mini-implants placed. Each mini-implant group were immediately applied with a continuous traction force of 150 g using a Ni-Ti coil spring. The rabbits were sacrificed 6 weeks post-surgically. Subsequently, the legs were stabilized, the Ni-Ti coil springs were removed and the mini-implants were removed under reverse torque rotation with a digital torque gauge. Results: 6 weeks after placement, the SIA group presented a higher mean removal torque value (8.29 Ncm) than the smooth group (3.34 Ncm) and histologic analysis revealed a higher new bone formation aspect along the screw in the SLA group. Conclusion: Results of this study indicates that SLA treated mini-implants may endure higher orthodontic forces without loosening.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.34-39
• /
• 1995

최근 승용차의 급격한 수요증가와 더불어 차량의 승차감 개선에 많은 관심이 집중되면서, 저진동 저소음 차량에 대한 연구가 활발히 이루어지고 있다. 이러한 연구의 일부로서, 수치해석법 및 진동실험에 의하여 복잡한 전체 구조물을 해석할 경우, 계산기의 기억용량, 계산시간, 비용이 많이 들게 되고, 한번 해석을 행한 구조물을 부분적으로 변경할지라도 전체의 계산을 다시 수행해야만 한다. 그래서, 복잡한 전체 구조물을 몇 개의 부분구조물로 나누어, 분계의 특성에 맞게 각기 수치해석법이나 모달실험을 적용한 후, 다시 합성하는 방법이 제시되었는데, 이것이 부분구조합성법이다. 이 방법을 사용하면, 유한요소 모델링이 쉬운 분계와 실험이 쉬운 분계를 서로 구분하여 각기 해석한 후 합성함으로써, 각 분계의 특성에 맞는 효율적인 해석을 수행할 수가 있다. 지금까지의 연구를 살펴보면, 유한요소해석에 의한 모드합성법에서는 Hurty가 구속모드법을 제안한 이래, 불구속모드법, 주종계법 등 많은 연구가 있었으나, 실험모달해석을 병행할 경우에는 결합부에서의 회전자유도의 처리문제, 특성 행렬의 동정문제, 많은 절점으로부터 데이타를 얻어야 하는 등의 어려움이 있었다. 이러한 문제를 개선시켜서 Hermanski등은 회전자유도가 보간된 모드합성법(interpolated mode synthesis, IMS)을 연구하여, 적은 실험데이타만을 사용하면서 단순지지 보에 적용함으로써 타당성을 입증하였다. 한편, 차체는 복잡한 부분구조물들로 이루어져 있으므로, 본 연구에서는 유한요소모델링의 용이함, 실험의 간편성, 계산의 효율성등을 추구하며, 실험과 유한요소해석을 병행한 부분구조합성법을 차량의 BIW(body in white)에 적용하는 방법을 연구하게 되었다. 그 기본연구로서 실험과 유한요소해석을 병행하여 회전자유도를 보간하는 방법을 먼저 단순한 판구조물에 적용을 하고, 나아가 실제 BIW를 축소하여 자체 제작한 모형차에 적용시켜 보았다.물은 분계 A(16개의 사각요소)와 분계 B(8개의 사각요소)로 이루어져 있으며 두개의 스프링으로 결합되어 있다. 설계변수는 강성에 국한하였으며 결합부의 결합형태는 탄성결합과 강결합으로 하였다. 감도해석과 축소임피던스 합성법에 의해 구해진 고유진동수와 FRF를 상용 유한 요소 해석 패키지인 MSC/NASTRAN을 통하여 검증하여 이 연구의 타당성을 검토하였다.인풋기어에서의 회전수 변동을 측정하고, 이 실험 데이타를 기초로 하여 엔진 토크 및 변속기에서의 드래그 토크를 계산하여 엔진-변속기 인풋기어의 반한정계 2자유도 진동모델과 비틀림 특성을 가진 클러치 디스크의 프리댐퍼 영역에 대해 시뮬레이션을 수행하여 클러치 비틀림 기구의 설계인자인 비틀림 강성, 히스테리시스 토크에 따른 비틀림 진동 저감 효과를 연구하고자 한다.성을 확인하였다. 여기서는 실험실 수준의 평 판모델을 제작하고 실제 현장에서 이루어질 수 있는 진동제어 구조물에 대 한 동적실험 및 FRS를 수행하는 과정과 동일하게 따름으로써 실제 발생할 수 있는 오차나 error를 실험실내의 차원에서 파악하여 진동원을 있는 구조 물에 대한 진동제어기술을 보유하고자 한다. 이용한 해마의 부피측정은 해마경화증 환자의 진단에 있어 육안적인 MR 진단이 어려운 제한된 경우에만 실제적 도움을 줄 수 있는 보조적인 방법으로 생각된다.ofile whereas relaxivity at high field is not affected by τS. On the other hand, the change in τV does not affect low field profile but strongly in fluences on both inflection fie이 and the maximum relaxivity value. The results shows a fluences on both inflection field and the maximum relaxivity value. Th

• Journal of Astronomy and Space Sciences
• /
• v.13 no.2
• /
• pp.173-180
• /
• 1996

This paper briefly describes the KITSAT-1 and KITSAT-2 spacecrafts and presents the functions, calibration procedures and in-orbit results of the KITSAT-2 analog sun sensors have been flown as an experimental payload for the future mission. We have two constraints in their design: small size and very low power consumption due to the tight mass and power budget of the spacecraft. Two one-dimensional analog sun sensors are mounted on the top facet of the KITSAT-2 spaceraft. Each has $\pm$60 degrees of view angle and they cover 210 degree field of view in total as the 30 degree view angles are overlapped. Only the relative sun angle around the Z-axis (yaw-axis) and the spin rate of the spacecraft can be achieved as the one dimensional sun sensors are used and they are aligned with the Z-axis. The calibration formulae are obtained using the fifth order line fitting algorithm for each sun sensor on the ground and they are applied to the obtained in-orbit data. ASS-1 with silicon solar cells has maximum error of 1.5 degree and ASS-2 with silicon photocells manufactured at KAIST has maximum error of 0.5 degree except near 0 degree of sun ray incident anagle where random reflection of incident sun ray is maximum in orbit. The results are presented in chapter 4. The performance of each sun sensor and the possible mounting errors are stated in chapter 5.