• 소음진동
• /
• 제10권3호
• /
• pp.493-499
• /
• 2000

Structural vibration analysis of the stationary power plant system employing a large two-stroke low speed diesel engine is performed to verify that the vibration characteristics of the system meet design requirements, The system consists of the diesel engine generator and concrete foundation including pile and soil. The system is modeled in the form of a mass-elastic system of 5 degrees of freedom for vibration analysis. Excitation moments and dynamic parameters including engine body stiffness soil stiffness and damping are identified for the analysis, Results of structural vibration analysis of the system are presented and compared with measurements in this paper.

• 한국소음진동공학회논문집
• /
• 제25권1호
• /
• pp.40-47
• /
• 2015

Dynamic response of any small structure is always affected by the mass of the attached accelerometer. This paper predicts the natural frequencies and frequency response functions by removing the mass loading effect from the accelerometer. This mass loading is studied on a simple cantilever beams by varying the location of accelerometer. By using sensitivity analysis with iteration method, accelerometer mass and location are obtained. The predicted natural frequencies of the small cantilever beam without the accelerometer's mass show good agreement with the structural re-analysis.

• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.89-96
• /
• 2004

Micro-tensile testing system, consisting of a micro tensile loading system and micro-ESPI(Electronic Speckle Pattern Interferometry) system, has been developed for measurement of micro-tensile properties of thin micro-materials. Micro-tensile loading system had a load cell with the maximum capacity of 50N and micro actuator with resolution of 4.5nm in stroke. The system was used to apply a tensile load to the micro-sized specimen. During tensile loading, the micro-ESPI system acquired interferornetric speckle patterns in the deformed specimen and measured the in-plane tensile strain. The ESPI system consisted of a CCD-camera with a lens and the window-based program developed for this experiment. Using this system, stress-strain curves for 4 kinds of electrolytic copper foil 18$\square$m thick were obtained. From these curves, tensile properties, including the elastic modulus. yielding strength and tensile strength, were determined and also values of the plastic exponent and coefficient based on Ramberg-Osgood relationship were evaluated.

• 한국유체기계학회 논문집
• /
• 제14권1호
• /
• pp.5-10
• /
• 2011

MTG(Micro turbine generator) operating at 400,000 rpm is under development and the impact test rig to measure the dynamic stiffness and damping coefficient of air foil bearing for high speed rotor is presented in this study. The stiffness and damping coefficient of air foil bearing depending on the rotational speed can be measured easily and effectively by using the simple configuration of impact test rig which is composed of air gun, gap sensors and high speed motor. The estimation results of stiffness and dampling coefficient using least square estimation method is presented as well.

• 한국소음진동공학회논문집
• /
• 제27권2호
• /
• pp.162-167
• /
• 2017

The chevron rubber spring is used for subway vehicle as a primary suspension. Generally, the primary suspension has an influence to the running performance and not so much effect on the ride comfort in railway vehicle. But the stiffness of chevron spring is harder and harder as time goes on because of rubber characteristics. Therefore the dynamic characteristics such as ride comfort and derailment coefficient should be reviewed according to the stiffness variation of chevron rubber spring. In this paper the effect of chevron rubber spring on dynamic characteristics was studied by considering multi-body dynamics of railway vehicle on one straight line and seven curved lines.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송공학회 2011년도 하계학술대회
• /
• pp.284-286
• /
• 2011

LDPC(low density parity check) 부호는 낮은 복잡성과 Shannon의 한계에 근접하는 오류 정정 능력을 보이기 때문에 turbo 부호와 함께 많은 응용분야에 적용되고 있다. 본 논문에서는 분산 동영상 부호화(distributed video coding: DVC) 시스템을 위한 부호율 적응적인(rate adaptive) LDPC 부호를 설계하기 위하여 패리티 점검 노드를 병합하는 방법을 제안한다. ACE(approximation cycles EMD) 알고리즘을 기반으로 효율적인 LDPC 부호를 설계하고 부호율 적응적인 특성을 갖기 위해 일정한 범위를 지정하고 지정된 범위에 따라 패리티 점검 노드를 병합한다. 그리고 ACE 알고리즘의 계수와 degree distribution을 변화시키면서 성능을 해석한다.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.313-321
• /
• 1995

The effects of the temperature rise and the turbulence are very important factors to predict the accurate performance of a large tilting pad journal bearing. In this study, the dynamic characteristics of a large tilting pad journal bearing are analyzed, taking into account the three dimensional variation of lubricant viscosity and turbulence. The effects of the temperature rise and the turbulence on the stiffness and damping coefficients are investigated in comparison with the results from the laminar or isothermal theory. The stiffness and damping coefficients increase due to the turbulence but decrease due to the temperature rise. The results show that the effects of both the temperature rise and turbulence must be considered simultaneously in order to predict the dynamic characteristics of a large tilting pad journal bearing more accurately.

• 소음진동
• /
• 제8권4호
• /
• pp.690-699
• /
• 1998

This paper discusses the techniques, procedures and the results of the ground vibration test(GVT) performed on the development aircraft and the simple procedure of FE model updating technique from the GVT results. The GVT was carried out using random excitation technique with MIMO(Multi-Input-Multi-Output) data acquistion method, and taking full advantage of poly-reference global parameter estimation technique to identify the vibration modes. In dynamic FE modeling, the aircraft was represented by beam elements and all dynamic analysis was performed using MSC/NASTRAN for this model. In updating procedure, the stiffness of the beam model was adjusted iteratively so as to get the natural frequencies and mode shapes close to the GVT results.

• 한국생산제조학회지
• /
• 제19권2호
• /
• pp.191-197
• /
• 2010

In spite of a large amount of previous research, detail study on modified mass in proportional damping system is not well understood. It is common to predict structural dynamic design parameters due to the change of mass, but to predict the amount of modified mass and the location where the mass is being modified are rarely found in previous literature. Such inverse problem required detail analytical study in order to understand structural modification in proportional damping system. This paper predicts the modified mass and the modified mass location in proportional damping system using sensitivity coefficients and iterative method. The sensitivity coefficients are obtained from the change of eigenvectors due to mass modification. This method is applied to a horizontal beam and three degree of freedoms system. To validate the predicted changing mass and its location, the obtained results are compared to the reanalysis result which shows good agreement.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1648-1653
• /
• 2003

This paper predicts the modified proportional damping structural eigenvectors and eigenvalues due to the change in the mass and stiffness of a proportional damping structure by iterative calculation of the sensitivity coefficient using the original dynamic characteristics. The method is applied to examples of a cantilever and 3 degree of freedom lumped mass model by modifing the mass and stiffness. The predicted dynamic characteristics are in good agreement with these from the structural reanalysis using the modified mass and stiffness.