• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.8
• /
• pp.2601-2610
• /
• 1996

Surface protrusions have been attached on a cylinder surface to reduce the flow-induced structural vibration by controlling the wake flow. Wind tunnel tests on the near wake of a circular cylinder with surface protrusions were carried out to investigate the flow characteristics of the controlled wake. Three experimental models were used in this experiment; one plain cylinder of diameter D and two cylinders wrapped helically by three small wires of diameter d=0.075D with pitches of 5D and 10D, respectively. Free stream velocity was ranged to have Reynolds number from 5000 to 50,000. Streamwise and vertical velocity components of the wake were measured by a hot-wire anemometry. The spanwise velocity component measured by a one-component fiber optic LDV revealed that time-averaged wake field has a nearly two-dimensional structure. It was found that the surface protrusions elongate the vortex formation region, which decrease the vortex shedding frequency. The suppression of vortices caused by the surface protrusions increases the velocity deficit in the center of wake region.

• Development and Reproduction
• /
• v.4 no.1
• /
• pp.1-6
• /
• 2000

Ultrastructure of the zona radiata the micropyle and fertilization process in the rainbow trout (Oncorhynchus mykiss) were examined by light, scanning and transmission microscopes . The egg micropyle of rainbow trout consists of a funnel-shaped vestibule and a tapered canal transversing the zona radiata. The micropyle showed the type with a flat pit leading into a long canal and the micropylar wall showed the clockwise spiral structure. There were a great number of microvilli secreting adhesive materials having trapping function attracting the spermatozoa in the vicinity of micropyle. It was apparent that ridges extended between the projections. In the initial stages of penetration, the spermatozoon still within the micropylar canal attached perpendicularly at its apical tip to the egg surface, then the sperm head was rapidly engulfed by the folded egg surface with its many microvilli. The spermatozoon disappeared from the outer surface of the egg before the fertilization cone completely retracted 250 seconds after insemination. No interconnecting ridges was present in the egg surface. In short, the block to polyspermy to permit entry of a single sperm is considered to be mechanical by the morphological design of the micropyle and fertilization cone.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.2
• /
• pp.29-38
• /
• 2022

The friction anisotropy of shear resistance can be selectively used in geo-structures. For example, larger axially loaded deep foundation, soil nails, and tiebacks increase load carrying capacity due to induced large shear resistance while pile penetration and soil sampling produce minimal shear resistance. Previous studies confirmed direction-dependent shear resistance induced by interface between soil and surface asperity of plate inspired by geometrical shape of snake scale. The aim of this paper is to quantitatively evaluate interface friction angle with different surface asperities. Using the modified direct shear test, a total of 51 cases, which sand are prepared at the relative density of 40%, are conduced including 9 plates, two shear direction (shearing direction against the height of surface asperity is increased or decreased during shearing test), and three initial vertical stress (100 kPa, 200 kPa, 300 kPa). Experimental results show that shear stress is increased with higher height of surface asperity, shorter length of surface asperity, and the shearing direction that the height of surface asperity increases. Also, interface friction angle is decreased with larger surface asperity ratio, and shearing direction with increasing height of surface asperity produces larger interface friction angle regardless of the surface asperity ratio.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.244-244
• /
• 2022

4차 산업혁명에 따라 유역 및 하천관리 사업, 각종 풍수해 예방사업 분야에 다양한 스마트기술이 도입되고 있으나 건설현장 침수 피해 사고는 지속적으로 발생하고 있다. 굴착공사 현장에서 발생할 수 있는 침수피해를 사전에 예측하기 위해서는 공정별로 변화하는 현장상황을 반영하여 다양한 강우 시나리오를 기반으로 침수 예측 모델링이 선행되어야한다. 따라서 본 연구에서는 2차원 동수역학 모형인 HDM-2D 모형을 기반으로 굴착공사 현장 침수피해 예측 모델을 개발하여 굴착공사현장 침수 예·경보 시스템에 탑재하고자 한다. 침수피해 예측 모델은 천수방정식을 Petrov-Galerkin stabilized scheme 으로 이산화하여 해석하는 수평 2차원 동수역학 흐름해석모델로서 수로 및 지표면 등 다양한 지형 상황에서의 물 흐름을 상세하게 해석할 수 있다. 지형자료 생성 이후 경계조건 부여를 통해 수행되며 침수발생지역의 유속, 수심, 수위를 취득할 수 있다. 배수지나 굴착공사 현장에 2차원 흐름해석을 적용하는 경우 지형의 경사나 배치가 공간에 따라 변화하므로 불연속적인 흐름을 유발하여 모의결과의 계산 오차를 검토해야 한다. 2차원 침수피해 예측 모형의 정확성을 확인하기 위해 지면 돌출부가 있는 흐름 문제와 테스트베드 대상지에 침수해석 모형을 적용하였다. 돌출부 흐름 문제의 경우 돌출부를 지나며 발생하는 유속과 수심 모의 결과를 상용모형과 비교검증 하였으며 테스트베드 대상지역에 침수피해예측모형을 적용했을때 지형 경사에 따른 흐름의 변화와 침수양상을 확인할 수 있었다.

• Journal of the Korean Institute of Gas
• /
• v.17 no.5
• /
• pp.37-41
• /
• 2013

This paper presents the strength safety of stress and deformation behaviors using the finite element method as a function of the thickness of the protective helmets with and without an extruder on the top of the shell structure. The helmet that would provide head and neck protections without causing discomfort to the user when it was worn for long periods of time should be manufactured for increasing the safety and impact energy absorption. The stress analyzed results show that when the impulsive force of 4,540N is applied on the top surface of a helmet, the safe thickness is 3.7mm for the conventional helmet and 3.2mm for the modified new helmet. Based on the deformation analysis, the FEM results recommend that the safe thickness is 3.2mm for the conventional helmet and 2.0mm for the modified new helmet. Thus, it may be more safe design of the helmet, which has an extruded structure on the summit surface of the helmet.

• Parasites, Hosts and Diseases
• /
• v.23 no.1
• /
• pp.111-122
• /
• 1985

The present study was performed to observe the ultrastructure of the integument of adult Paragonimus westermani. Dogs experimentally infected with 60 metacercariae of F. westermani were autopsied 4 months after the infection. Adult p. westermani were extracted from the dogs and the fine structure was studied by means of scanning and transmission electron microscope. The findings are as follows: 1. Scanning electron microscopic findings showed that the spines and the papillae are distributed at whole body surface but the well developed spines or papaillae are shown around the oral sucker and ventral sucker. 2. At the end of the body, excretory pore was found, the shape was irregular. 3. Transmission electron microscopic findings showed that plasma membrane, tegument, basal lamina, connective tissue, circular muscle layer, longitudinal muscle layer. nerve axon and tegumental cell were observed. 4. In higher magnification, plasma membrance and bar-shaped granules were found at the outer surface of the tegument.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.1
• /
• pp.122-130
• /
• 1998

The present work analyzes the pressure drop and heat transfer characteristics of the plate heat exchanger with staggered dimples. The flow is assumed to be constant property, three dimensional and laminar. A thermal boundary condition is uniform wall temperature and it is assumed that the flow is periodically fully developed. Elliptic grid generation is used for proper modelling of the internal tube geometry with dimples. Computations have been carried out for a variety of geometric parameters, Reynolds number, and Prandtl number. The friction factor ratio and the ratio of a module average Nusselt number are presented for the cases considered in this study. It is found that the distance between dimples has a substantial effect on the pressure drop and heat transfer.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.2 s.152
• /
• pp.101-110
• /
• 2007

Recently, rudder erosion due to cavitation frequently has occurred at large high speed container carriers. Especially, in the case of a horn-type rudder, the rudder erosion is severe around a gap. The gap-flow characteristics are investigated through a computational method to understand the effects of a gap on the cavitation and rudder efficiency. A viscous flow theory utilizing a cavitation model is applied to calculate the flow around idealized 2-dimensional rudder sections in a full scale. The effects of gap clearance and flow-control projection are also investigated. From the computational results, the mass flow rate through a gap is found to be one of the important parameters to affect the cavitation and rudder efficiency.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.2
• /
• pp.523-536
• /
• 1991

This dissertation analyzes the running mechanism of flexible and thin tape above rotating head through the numerical simulation and the experiment. The scope of analysis is confined to the phenomena of two dimensional elasto hydrodynamic lubrication between the protruded bump on a rotating cylinder and the running tape. This model is based on the elastic deformation equation of plate and shell and Reynolds equation. Finite difference method is employed as a numerical technique to calculate (1) the distribution of pressure between the running tape and rotating bump and (2) the vertical deformation of elastic thin tape over he rotating bump under hydrodynamic pressure. In numerical analyses, the effects of bump size on flying characteristics of the tape were evaluated and examined considering the influence of tension and stiffness of tape.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.570-571
• /
• 2014

차량의 고속 주행 시 운전자가 인지하게 되는 공력소음은 대부분 차량 전방부의 A 필라 부근에서 발생하는 소음원에 의해 전달된다. A 필라 부근에는 다양한 모양의 돌출물들이 부착되어 있어서 차량 주변의 고속의 유동과의 상호 작용에 의해 다양한 공력 소음이 발생하게 된다. 이러한 차량 전방부의 대표적인 소음 인자인 A 필라 형상에 의한 와류 및 아웃사이드 미러에 의한 유동 구조 변화에 의한 실내 투과 소음에 대해 실험 및 소음원 분석을 수행하였다. 차량 내외부의 복잡한 구조와 재질에 의한 영향을 최소화 하고자 실차 형상 및 실내 조건을 간략화 시킨 차량 단순 모델을 이용해서 A 필라 주변부의 형상에 의한 주요 주요 공력 소음 인자에 대해 기여도를 분석했으며, 실험 결과는 다양한 CAE S/W 의 실내음 예측 결과의 정밀도를 분석하기 위해 사용되었다.