• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.4
• /
• pp.77-86
• /
• 1993

Recently it is reported in many countries that highway bridges are seriously damaged due to increasing volume of overloaded heavy vehicles. The safety of bridges are highly related to the design load level and the characteristics of extreme load effect induced by traffic loads during its lifetime. The maximum structural load effect during lifetime may be produced by simultaneous loading of trucks with moderate weights on a bridge rather than by single loading of extremely heavy trucks. In this study, a simulation technique to estimate extreme load effect due to traffic loadings has been developed, in which important characteristics of traffic loadings, such as heavy vehicle proportion, traffic mode, vehicle weights, headway distribution. daily traffic volume, etc., should be properly considered. In addition. sensitivity analysis on those factors have been performed.

• International Journal of Highway Engineering
• /
• v.14 no.2
• /
• pp.29-36
• /
• 2012

In this study, frequently passing vehicles with two, three, four, and five axles were chosen through traffic volume analysis in Kyung-In Expressway in order to analyze how the road roughness and vehicle speed affect on the dynamic loads for roads in various vehicle classes. Dynamic loads according to chosen vehicles are estimated by TruckSim program. Dynamic load amplification factor is ratio between dynamic and static loads, and it is also determined for each vehicle classes. From the result of dynamic loads estimated by the dynamic load amplification factor, it is shown that for three-axles vehicle, when IRI is 3.5 and vehicle speed is 100km/hr, asphalt pavements receive additional 36% of static loads in maximum. The analysis of the amplification factor according to each vehicle classes also indicates that the amplification factor increases as the distance between the axles becomes smaller and each axle receives more loads.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.1
• /
• pp.37-44
• /
• 2023

In this study, the performance of the support modular system, as substructure of the proposed sustainable-perpetual modular road system to reduce road construction time and maintenance costs was evaluated. A modular road system consisting of 4 support modular cross-beams with a lower curved surface was constructed on the test-bed. Six load cells and eight LVDTs were installed in the center part of two cross-beam support modular systems. Two loads, 50kN and 100kN, were applied to 15 points on the pavement slab to measure the load and displacement occurring in the modular road system. The measured displacements were less than 1 mm, so it is considered that there was no problem in the stability of the actual road. When comparing the two applied loads and the measured loads in the field test, it was considered that the load transmitted to the ground under the support modular system is very small. It is considered that the modular road system with the support modular system is applicable to the actual road site.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.315-316
• /
• 2003

차량의 통행이 빈번한 기존 아스팔트 도로는 연속적인 차량의 하중에 의한 스트레스로 하중을 받을 때마다 아스팔트도로 층의 강도와 안정성이 떨어지면서 균열이 발생하고 이 균열이 아스팔트 도로 상층부까지 전달되는 반사균열이 발생한고, 열팽창과 수축의 반복에 기인하는 상부의 아스팔트 층의 피로에 의한 균열이 발생한다. 따라서 아스팔트 도로의 반사균열을 억제하고, 아스팔트의 소성변형에 의한 rutting현상을 억제하여 아스팔트의 도로보수 주기를 연장하여 도로상에서의 잦은 보수에 의한 자동차의 정체현상을 줄이고 도로유지에 소요되는 비용을 절감하기 위해서 아스팔트 도로를 설치할 때 아스팔트를 보강시켜주는 geogrid의 사용이 보편화 되고 있다. (중략)

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.4
• /
• pp.107-116
• /
• 1992

The structural integrity of bridges is mainly damaged by overloaded heavy vehicles. The increasing volumes of overloaded heavy vehicles has been indicated as serious state. As results several countries have revised their bridge load codes. However, because of variety of truck types and their weights it is difficult to develop rational standard truck loads. In addition the common practice that only one design configuration of standard truck is adopted to design variety of bridges causes further difficulties. The objective of the study is to investigate the statistical characteristics of vehicle loadings based on survey data collected, in which some major factors, such as vehicle configurations, vehicle weights, traffic modes, etc., are incorporated. The vehicle load effects due to single presence of heavy truck are also tested with several short-span bridges and probabilistic characteristics of current design practices are evaluated.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1D
• /
• pp.127-132
• /
• 2011

Load managing method on road became necessary since overloaded vehicles occur damage on road facilities and existing systems for preventing this damage still show many problems. Accordingly, efficient managing system for preventing overloaded vehicles could be organized by using the road itself as a scale by applying genetic algorithm to analyze the load and the drive information of vehicles. First of all, accurate analysis of load using the behavior of road itself is needed for solving illegal axle manipulation problems of overloaded vehicles and for installing intelligent embedded load analyzing system. Accordingly in this study, to use the behavior of road, the transformation was measured by installing underground box type indoor model and indoor experiment was held using genetic algorithm and 10% error were checked.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.2
• /
• pp.237-244
• /
• 2024

Pavement management systems (PMS) provide procedures to quantify road serviceability based on pavement conditions such as cracks and plastic deformation and suggest proper maintenance methods. The deterioration of the road pavement is relevant to the time although the quantifications on road serviceability in PMS present road surface conditions at the evaluation. More systematic evaluation on road serviceability may need time-dependent factors of road environments and that can improve PMS. Rainfall, temperature and vehicle loads can be environmental factors for road serviceability evaluation. As no data are avablie that can link between road conditions and environmental road factors, we conducted experiments to suggest economical devices and methods to obtain relevant data. We used temperature sensors and accelerometers with Arduino to measure road surface temperature and dynamic loads and provide data to improve pavement serviceability evaluation.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.6
• /
• pp.553-561
• /
• 2009

Risk analysis of highway sign supporting structures and sound barriers was done. Stochastic wind load was modeled by using extreme value distribution from site measurement and the variability of structural parameters was considered. Limit state functions were defined to assess structural stability by wind and risk of highway facilities was analyzed by combining wind hazard. According to the numerical analysis results, sound barrier post shows significantly higher risk than highway sign supporting structures. This is caused by the fact that the design codes of the structures are different. To distribute wind induced risk in highway structures, unification and improvement of design codes are required based on risk assessment.

• International Journal of Highway Engineering
• /
• v.10 no.1
• /
• pp.135-144
• /
• 2008

The dynamic loads imposed by moving vehicles have variations in the magnitude due to the surface roughness of the pavement systems and the larger dynamic loads than the design loads may affect the pavement performance. This paper presents variations of the moving dynamic vehicle loads due to the pavement surface roughness. This study was performed as a basic study to apply the pay factor to the surface roughness for the improvement of pavement quality and performance. The profile data was obtained from the old and new pavements and the analysis was performed to investigate the dynamic loads when vehicles move on the pavements having those profiles. The artificial profiles were also developed to find the effects of the vehicle speed, wavelength and amplitude of the surface roughness on the dynamic vehicle loads. The increase in the load magnitude due to the surface roughness affects the stresses and strains of pavements and finally reduces the pavement life. The methodology to obtain the relationship between the surface roughness and the pavement performance was proposed in this study.

• Aerospace Engineering and Technology
• /
• v.2 no.2
• /
• pp.105-114
• /
• 2003

It is conducted to analyze vibration loads on the 1st stage of KSR-III(KSR : Korea Sounding Rocket) during their ground transportation and various handling process. These loads may be different from the real flight environment. Inadequate assessment of these loads can cause not only local damages on the rocket system but also the critical problem like flight mission failure. Therefore, transportation and handling loads must be considered during design and attenuated to ensure that the rocket structural damage does not occur. This work is concerned with the generation of criteria and prediction of transportation and handling loads for KSR-III. The results show that the shipping container is well designed to satisfy the design requirements. The maximum vibration level recorded during whole transportation and handling for KSR-III is less than 2g, the criteria of KSR-III movement condition.