• Journal of Korean Society of Disaster and Security
• /
• v.15 no.3
• /
• pp.15-21
• /
• 2022

The purpose of this study is to investigate the sedimentation area and runout distance in the downstream when debris flow occurred on a mountain slope through an experimental performance. Super typhoons and torrential rains caused by climate change cause large-scale debris flow disasters in the downstream areas of mountainous areas, mainly where sediments are deposited and flowed downstream. To analyze the characteristics of the sediment deposited downstream, the disposition area and runout distance were investigated through experiments in the case of a straight channel and channel with berm, respectively. As experimental conditions, changes in sediment volume concentration and channel slope, and channel with or without berm, reduction rates in sedimentation area and runout distance were investigated. In the straight channel, the steeper the channel slope and the lower the sedimentation concentration, the sedimentation area and runout distnace were increased. In a channel with berm, the runout distance and sediment area increased as the slope became steeper and the sediment area decreased.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.323-323
• /
• 2011

산지가 많은 국내의 지형적인 여건은 토지의 이용에 다양한 영향을 준다. 산지주변에서는 능선을 따르거나 가로지르는 도로가 건설되고 산지계곡 하류에 발달한 선상지에는 가옥이 들어서거나 경작지로 활용되고 있다. 이러한 환경에서 우리나라는 지난 10년간 사면재해로 인한 사망자가 전체 자연재해에 27%에 달하고 이는 집중호우가 발생하는 시기에 집중되고 있어 이에 대한 연구가 필요한 실정이다. 본 연구에서는 호우 발생 시 산지하천에서 발생하는 토석류의 흐름특성을 연구하기 위해 국내 외 토석류 실험장치에 대한 조사와 토석류 실험장치를 개발하여 토석류발생 및 도달거리 예측을 위한 실험을 수행하였다. 토석류 실험장치는 수조길이 5.5m에 10-40cm의 가동폭 그리고 상 중 하류의 3단계 경사조절이 가능하며 토석류 퇴적장치를 결합하여 도달거리 및 퇴적분포를 계측할 수 있다. 토석류를 발생시키기 위해 토사공급장치 이용방법, 하상퇴적토사를 이용한 방법 등 다양한 시도를 하였다. 토석류 실험장치를 이용하여 발생시킨 토석류의 특성과 퇴적장치 에서의 도달거리를 측정하여 유량공급과의 상관관계를 분석하였다. 이러한 연구결과는 토석류 재해지도의 작성이나 토석류 해석모형의 개발에 필요한 기초자료로 활용될 수 있다.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.6
• /
• pp.511-518
• /
• 2023

Accurate ranging is one of the key factors in the test and evaluation process of underwater vehicles. In particular, when estimating range using Time of Arrival (ToA) values, signals such as Linear Frequency Modulation (LFM), a chirp signal, are highly applicable due to their correlated nature. However, in a Doppler shift environment with mobility, measurement errors may occur due to the range-Doppler coupling effect. In this paper, we propose a signal that compensates for the distance-Doppler coupling effect to reduce the measurement error of the arrival time value. The proposed signal is constructed by superimposing two types of LFM signals, and the range-Doppler coupling effect can be minimized. Through simulations, it is confirmed that the proposed signal is a way to compensate for the distance-Doppler coupling effect in the distance estimation of underwater mobile bodies, reducing the measurement error of the arrival time value.

• Journal of Bio-Environment Control
• /
• v.6 no.3
• /
• pp.183-189
• /
• 1997

This study was performed to Investigate size of droplet sprinkled from mini-sprinkler. Twelve different kinds of the sprinkler having various structures and sizes of nozzle orifices were selected and tested. Diameters of the droplet reached at several distances from a sprinkler were measured by a machine vision system and the volume median diameters (VMM) were determined statistically. The size of droplet was not affected much by the size of nozzle orifice of a sprinkler but was rather more affected by structure of the sprinkler, especially by the shape of spreader of the sprinkler. Experiment of varying pressure of sprinkling water validated that the size of droplet was inversely proportional to water pressure powered by 1/3. Hence the size of droplet at any water pressure could be easily estimated from experimental data. The size of droplet increased as travel distance of the droplet increases in a relationship of and order function. The size of droplet of the tested sprinkler were in the ranges of 100-300fm within 1m of droplet travel distance, 230~470${\mu}{\textrm}{m}$ within 1~2m of droplet travel distance and 300~770${\mu}{\textrm}{m}$ within 2~3m of droplet travel distance.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.1
• /
• pp.140-152
• /
• 1989

The study on the penetration of sprays during the initial phase of injection period, i.e. ignition delay period, in high speed small D.I. diesel engines are strongly affected by such behavior. To investigate the penetration of the sprays injected through single cylinderical orifice, a mathematical model was developed and compared with experimental results. In this model, radial heterogeneity of fuel density in the spray, transiency of injection pressure difference, and spray outrunning phenomenon were considered simultaneously. Experiments on the behaviors of sprays in the high pressure air chamber were conducted at various injection pressure differences and different levels of back air pressure. The behaviors of sprays injected into the chamber through the conventional Bosch injection pump were visualized with side stroboscopic illumination. Comparison of the experimental results with predictions from the mathematical model confirmed the validity of the model. It was also found that during the initial phase of the injection period the penetration of sprays vs. time appeared to have two transition points; one corresponded to disintegration point of liquid fuel jet, the other to the beginning of steady state injection.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.2
• /
• pp.154-159
• /
• 2019

When measuring the radiating noise of an underwater moving source, the range information between the acoustic source and the receiver is an important evaluation factor, and the measurement standards such as a receiver position, a moving source depth and a speed are set. Although there is a method of using the cross correlation as a method of finding the range of the underwater moving source, this method requires a time synchronization process. In this paper, we proposed the method to estimate the range by comparing the Doppler frequency difference of the theoretically calculated multipath signal with the Doppler frequency difference of the multipath signal estimated from the received signal. The proposed method does not require a separate time synchronization process. Simulations were performed to verify the performance, and the ranging error of the proposed method reduced by about 95 % than that of the conventional method.

• Journal of Biosystems Engineering
• /
• v.7 no.2
• /
• pp.30-35
• /
• 1983

To investigate the factors affecting the transportability of spray droplets, the maximum distance, the effective distance, the ratio of even distribution, and the diameters of particles were measured in accordance with the different pressure levels of power sprayer using 3 hole swath type nozzle, and the results are summerized as follows; 1. The distance of the most dense point from the nozzle was shortened by 0.5 meter with the 100-meter-long hose. The maximum reaching distances were reduced by 1.5 and 1.0 meters for the 13m/m and the 8.5 m/m hoses respectively, and the effective distance were reduced by 0.5 meter for both cases. 2. The effective distance can not be extended beyond 14 meters even if the length of hose is minimized at the rated pump pressure 28 kg/$cm^2$, it was 1 meter longer for 13m/m hose compared to the 8.5m/m one. 3. In case of 13m/m hose, the most dense point can be extended further by 0.5 meter increasing the pump pressure by 8 kg/$cm^2$, and the maximum distance and effective distance were increased by 2.0 and 0.5 meters respectively. There was no significant effect of pressure changes on the transportability in case of 8.5m/m hose. 4. Both the reduction of hose length and the increase of pump pressure influenced in large extent to the atomization effect of droplets. It was noticed that the diameter of droplet is related to the pump pressure and inside diameter of hose. 5. The pressure drop in 100-meter-long and l3m/m hose was 5~7kg/$cm^2$ at the pump pressure range of 25~33kg/$cm^2$, and it is an equivalent of 2% per 10 meter length of hose.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.11C
• /
• pp.957-964
• /
• 2010

In this paper, we propose an indoor positioning algorithm based on 3 points near field angle-of-arrival estimation without side information. The conventional angle-of-arrival based positioning scheme requires the distance between the listener and the center of two points which is obtained by a received signal strength based range estimation. However, a received signal strength is affected by structure of room, placement of furniture, and characteristic of signal, these effects cause a large error to estimation of angle. In this paper, the proposed positioning scheme based on near field angle-of-arrival estimation can be used to estimate the position of listener without a prior distance information, just using time-difference-of-arrival information given from 3 points microphones. The performance of the proposed scheme is shown by cumulative distribution function of root mean squared error.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.294-294
• /
• 2008

동시 증발 증착법 화합물의 구성원자를 독립적으로 증발시켜서 기판에 증착하는 방법이다. 각 물질은 온도에 따른 증기압을 가지는데 각 물질의 온도를 조절하여 증착률을 조절한다. 보트에서 떠난 원자가 기판에 도달할 확률은 챔버의 진공도, 보토와 기판과의 거리 등에 의하여 영향을 받는다. 진공도가 나쁠수록, 보트와 기판과의 거리가 멀수록 기판에 도달할 확률이 떨어진다. 동시증발 증착법을 이용한 SmBCO 초전도층 증착에서 각 물질의 기판에 도달하는 원자비를 조절하기 위하여 QCM(증착률 측정장치), QCM 가이드를 사용하였다. QCM sensor 입구에 튜브형태의 QCM 가이드를 설치하고 QCM 가이드가 특정한 물질의 증발보트를 향하도록 배치하였다. 따라서 각 보트에서 떠난 원자들은 특정한 QCM sensor에 도달하게 되고 결국 3원소(Sm, Ba, Cu)의 증착률의 비를 조절함으로써 조성비를 조절할 수 있게 된다. QCM 증착률의 비와 실제 조성비는 여러 가지 변수에 의하여 영향을 받는 다. 대표적인 변수는 챔버의 진공도, QCM 가이드의 직경 및 길이, QCM 센서와 보트와의 거리 등이 있다. 진공도가 높을수록 특정 보트에서 떠난 원자들이 QCM 가이드 입구에 도달할 확률이 낮아지고, QCM 가이드의 직경이 좁을수록 가이드 내벽에 흡착될 확률이 높아진다. 또한 QCM센서와 보트와의 거리가 멀수록 챔버내 잔류가스의 원자들과 충돌확률이 높아지므로 도달확률이 줄어들게 된다. 동시 증발 증확법에서 조성비의 재현성을 높이기 위해서는 매회 증착실험에서 진공도가 일정해야 하며, QCM 가이드와 보트와의 거리를 되도록 최소화 하고, QCM 직경을 크게 하는 것이 유리하다.

• Korean Journal of Agricultural Science
• /
• v.5 no.1
• /
• pp.29-34
• /
• 1978

In order to improve atomization of droplet of sprayers, gun-type nozzle equipped with swirl screw which could increase tangential velocity had been used in this study. The results obtained were as follow: The larger diameter of atomized droplet was, the longer it reached. Tile atomizing phenomenon while using swirl screw in the nozzle was more efficient. There was little difference of travelling distance in the both nozzles when the small diameter of disk hole was used, but thetravlling distance of the nozzle with swirl screw was evidently getting shorter with the increase of the hole diameter compared to that of the nozzle without swirl sorew. The size of sprayed particles was getting smaller owing to the phenomenon of air movement the one to two meters travelling distance of droplet from maximum travelling point.