• Fire Science and Engineering
• /
• v.23 no.6
• /
• pp.32-38
• /
• 2009

Owing to increase of the large-scaled, high-raised and complexed building construction, the escape design of the building became very important issue to insure the safety of occupant. Specially, it is demanded to have building escape regulation considering for inconvenient movers such as disables elders pregnant women. However, building regulations for inconvenient movers are divided into "Regulation of Escape and Fire-prevention of Building" and "Act on the Promotion and Guarantee of Access for the Disabled, the Aged and Pregnant Women to Facilities and Information". But, for the escape security of inconvenient movers, the connection of each regulation are necessary. So this study suggested the improvement direction of the building escape regulation considering inconvenient movers through the compared analysis on the "Regulation of Escape and Fire-prevention of Building" and "Act on the Promotion and Guarantee of Access for the Disabled, the Aged and Pregnant Women to Facilities and Information".

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.5
• /
• pp.519-530
• /
• 2022

As online commerce increases, the construction of large logistics buildings worldwide is exploding. Most of these buildings have the characteristics of long span and heavy loaded and use precast concrete components, a pin joint structure, for rapid construction. However, due to construction safety and structural stability requirements, the pin joint structure has many limitations in terms of the erection of the PC member, which increases the time and cost. A structural frame connected with steel joints between precast concrete components, called a SMART frame, has been developed, which addresses these constraints and risks. However, the effect of the appllication of a SMART frame on the time aspect has not been analysed. The study is a time reduction effect analysis of a SMART frame for long span and heavy loaded logistics buildings. For this study, the authors select a case site erected using existing PC components, and compare the time reduction with the SMART frame erection simulations. Through this analysis, it was found that a time reduciton about 4 months, approximately 48% of the conventional PC installation period could be achieved. If the SMART frame is applied when carrying out future large-scale logistics building projects, it can be expected to have the effect of significantly shortening the construction period compared to the conventional method.

• Archives of design research
• /
• v.15 no.4
• /
• pp.263-274
• /
• 2002

This study aims to analyze the image of long-span structures. For the intention, it analyzes the relationship between images and physical attributions of elements such as materials, stresses, configurations, compositions and shapes of structures. The image of structures can represent following 5 factors; friendly-unfriendly, strong-weak, dynamic-calm, superior-inferior, and regular-irregular. The friendly-unfriendly in the image of structure mostly determines on a finished material and partly with a structural shape. The strong-weak in the image of structure determines on configuration of the structural members. The dynamic-calm in the image of structure determines on the structural shape. Hence the structure has dynamic forms when it seems to be open and sharp, namely when it receives the flow of forces in the structural shape, and it has a (-) gauss curved rate or an diagonal appearance. The superior-inferior in the image of structure determines on composition of structural elements. The structure seems to be superior is contributed not simply to support load but positively to create design as a tectonic element. From now on, this study can provide the useful information on the long-span structure design through the more appropriate analysis of the image.

• Journal of the Korea Institute of Building Construction
• /
• v.13 no.6
• /
• pp.530-540
• /
• 2013

The business environment that affects the management performance can be characterized by each Strategic Business Unit (SBU) since construction companies win overseas contracts due to the fairly good construction situations while experience a decline in the local housing market. Environmental changes can alter the strategic importance of the SBU when measuring the management performance. However, large construction companies apply BSC (Balanced Score Card) for collective calculation to determine the management performance, making it difficult to reflect the strategic importance of SBU. This method may create a distorted image of management performance that fails to take environmental changes into consideration, and as such it needs to be improved. Yet, there are no studies on the weight of each SBU considering environmental changes. Thus, the current study intends to analyze the weight of SBU for company-wide measurement of the performance of large construction companies. In addition, a model for analysis of SBU importance is proposed to respond to the constantly changing environmental situations and to modify the weight. For analysis of SBU weight, a questionnaire was conducted with 23 experts and hands-on workers, and the questionnaire result was quantitatively analyzed by applying the FD-AHP method. It is expected that the result will enable a model to be proposed to calculate the weight per division in a manner that reflects environmental changes and minimizes strategic distortion when measuring the management performance of large construction companies.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.189-196
• /
• 2020

When concrete member become large like in high rise buildings, hydration heat makes temperature difference inside and outside and cause cracks. The method of using latent heat material as heat reducer could be more accessible, usable and efficient than other methods. Therefore, many studies using PCM as heat reducer are being conducted. Since heat reducer have different reacting temperature, they may be affected by environmental factors like ambient and concrete mixing temperature but studies issuing this are insignificant. Therefore, this paper attempt to evaluate the hydration heat characteristics and quality of concrete using strontium-based PCM under hot weather conditions. As a result, when the strontium-based hydration heat reducer was mixed 3wt.% and 5wt.% in hot weather condition, hydration heat speed and heating rate could be reduced by 8%, 21%, and 75, 85 minutes compared to OPC, respectively. This is considered to be the phase change reaction is relatively promoted when the temperature is high and cause improve performance than room condition result. Later, comparing the efficiency of other types of P.C.M in hot weather condition, and conduct detailed reviews on the strength development in long-term age.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.1
• /
• pp.91-99
• /
• 2008

The method to prepare the large cemented sand specimen for calibration chamber test by air-pluviation is investigated in this study. The uniformity of cemented specimen is evaluated by performing the CPTs, DMTs, and bender element tests in the calibration chamber. The sand particles, pre-wetted with 0.5% water content, are mixed with gypsum to provide the homogeneous coating of gypsum particles on the grain surface. It was shown that the pre-wetting of particle surface is effective to minimize the potential for segregation between sands and gypsum during air-pluviation. It was observed that the extreme void ratios ($e_{max}\;and\;e_{mix}$) of the mixture of pre-wetted sand and gypsum powder increase at lower gypsum content while those of the mixture of dry sand and gypsum decrease with increasing gypsum content. It was also shown from the test results that large cemented specimens reconstituted in calibration chamber by rainer system are quite uniform in vertical and horizontal directions.

• Fire Science and Engineering
• /
• v.21 no.4
• /
• pp.105-114
• /
• 2007

Recently the consideration for occupants' security has been raised as very important design element from the fire by building's large sized, higher storied, and its compounded. But the domestic Laws regulated the predicative laws according to the technical standard which has no difference from the past domestic evacuation regulations. Therefore when big fire occurs, it is not enough to guarantee for occupants to escape safely. Specially since domestic escape relevant laws are divided into Architect relevant law and fire fighting relevant law, it has caused to bring various problems. So This study will show the problems of the evacuation regulation which is registrated in the Architect relevant law and fire fighting relevant law. And also later, when Architect escape relevant laws re-registrate, this study will be used as foundational materials.

• Journal of the Korea Institute of Building Construction
• /
• v.21 no.2
• /
• pp.113-119
• /
• 2021

Polymers are widely applied to construction materials due to their lightweight and excellent mechanical properties. However, owing to the combustible properties, polymers are one of the biggest reason of spreading large fires in fire accidents that occur frequently in the construction industry. Therefore, as a solution to this problem, many research has been conducted to impart flame retardancy by incorporating flame retardants to polymer matrix. Among these flame retardants, organic phosphorus-containing flame retardants have been attracting much attention because they have excellent compatibility with polymer matrix and low toxicity compared with halogen or inorganic-containing flame retardants. Accordingly, this study aims to design and synthesize an alkoxyamine-based organic phosphorus flame retardant to improve flame retardancy of polylactide which is an eco-friendly polymer used for construction materials.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.4
• /
• pp.15-22
• /
• 2019

The use of modular buildings is increasing because of various advantages of modular buildings. But there are limits to apply modular buildings to medium-rise buildings because the building law provides only the specification criteria of the modular building with respect to the 1 hour fire resistance performance. This study was conducted to investigate 2 hours fire resistance performance of load bearing walls with steel studs in modular buildings by KS F 2257-1 and KS F 2257-4. After full scale tests, load bearing walls ensuring two hours fire resistance performance consist of at least 2 layers of fire resistance plaster boards of 19mm thickness or 3 layer of fire resistance plaster boards of thickness.

• Korean Journal of Construction Engineering and Management
• /
• v.23 no.1
• /
• pp.113-117
• /
• 2022

Additive manufacturing (AM, also known as 3D printing) technology is digitalized technology, making it easy to predict and manage quality and also, have design freedom ability. With these advantages, AM technology is applied to various industries. In particular, a method of manufacturing buildings and infrastructure with AM technology is being proposed to the construction industry. However, the application of AM technology is restricted due to problems such as insufficient history and quality of technology, lack of construction management methods, and certification of manufacturing products. Therefore, the manufacture of architectural products is implemented with indirect AM technology. In particular, it manufactures formwork using AM and injecting building materials to implement the architectural product. In this study, hybrid type material extrusion AM is used to manufacture large-sized formwork and implement building products. Moreover, we identify factors that can predict productivity and economic feasibility in the additive manufacturing process. As a result, design optimization results are proposed to reduce the production cost and time of architecture buildings.