• Journal of Korean Society of Forest Science
• /
• v.30 no.1
• /
• pp.19-29
• /
• 1976

The fiberboard and paper mills in this country are much affected by the price hikes and shortage of phenolic resins, since phenolic acid as a raw material depends on imported good. It is prerequisite to fiberboard industry to help replace with other sized and stabilize the prices and supply of them, improving the quality of boards. Thus, the present study was carried out to examine the effect of strength increasing sized such as urea formaldehyde resin (anion and cation type) and urea melamine copolymer resin, on the quality of the wet forming hardboard, and comparing them with two types of proprietary modified melamine resins, and ordinary size, phenol resin. The Asplund pulp was prepared from wood wastes mixed with 20 percent of lauan and 80 percent of pines as a fibrous material. After sizing agents were added at a pH of 4.5 for 10 minutes with alum in the beater, the stock was made in the form of wet sheet, prepared, and then performed by hot pressing cycle: $180^{\circ}C$, $50-6-5kg/cm^2$, 1-2-7 minutes. The properties of hardboard were examined after air conditioning. The results obtained are summarized as follows: 1. There is a significant difference in specific gravity among hardboards that were treated with strength increasing resins, but no difference is effected by the increase in the resin content. In the case of modified melamine resin, its specific gravity is highest. The middle group comprises cation type of urea resin, anion type of urea resin, and acid colloid of urea-melamine copolymer resin. The lowest is phenolic resin. 2. The difference of the moisture content of hardboard both by the resins and by the amount of each resin applied is significant. The moisture content of hardboard becomes lower along with the increase of each resin content, but there is no difference between 2 and 3 percent. 3. For water absorption, there is a significant difference both in the adhesives used and in the amount of paraffin wax emulsion. The water resistance becomes higher inn proportion to the content of the paraffin wax emulsion. To satisfy KS F standards of the water resistance, a proprietary modified melamine resin (p-6100) and modified cation type of urea resin (p-1500) do not require any paraffin wax emulsion, but in the case of anion type of urea resin, cation type of urea resin, and urea-melamine copolymer resin, 1 percent of paraffin wax emulsion is needed, and 2 percent of paraffin wax emulsion in the case of phenolic resin. 4. The difference of flexural strength of hardboard both by the resins and by the amount of each resin is significant. Modified melamine resin shows the highest degree of flexural strength. Among the middle group are urea-melamine copolymer resin, p-1500, anion type of urea resin, and cation type of urea resin. Phenolic resin is the lowest. The cause may be attributable to factors combined with the pressing temperature, sizing effect, and thermal efficiency of press platens heated electrically. 5. Considering the economic advantages and properties of hardboard, it is proposed that urea-melamine copolymer resin and cation type of urea resin be used for the development of the fiberboard industry. It is desirable to further develop the modified urea-melamine copolymer resin and cation type of urea resin through continuous study.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.12
• /
• pp.1589-1598
• /
• 2008

The objective of this study was to investigate the effect of obesity on health by analyzing the factors which are related to obesity through the questionnaires on the dietary pattern, nutrient intake and physical measurements. The subjects, 419 college women aged 20 to 24 year-old, were randomly selected from Seoul and data were collected during March to May, 2008 and classified as under underweight, normal weight, and obesity groups according to BMI. However, weight, skeletal muscle mass, body fat mass, fat free mass, percentage of body fat, and waist to hip ratio showed significant differences among all the groups (p<0.05). In the obese group, 77.8% ate fat-rich foods such as galbi and samgyopsal more than two times per week, 66.7% ate vegetables other than kimchi (p<0.05) as compared to the underweight and normal groups by mini dietary assessment (p<0.05). The cholesterol intakes of the underweight, normal weight, and obese groups were $164.67{\pm}114.52mg/dL$, $143.31{\pm}99.58mg/dL$, and $121.92{\pm}54.91mg/dL$, respectively, and the obese group had a significantly lower intake than the other groups (p<0.05). The serum total cholesterol levels of the underweight, normal, and obese groups were $177.04{\pm}26.36mg/dL$, $189.46{\pm}29.05mg/dL$, and $170.00{\pm}12.75mg/dL$, respectively, and the obese group showed lower total cholesterol level than the other groups (p<0.05). The triacylglycerol level of the obese group ($132.00{\pm}64.60mg/dL$) was significantly higher than the other two groups (p<0.05). The HDL-cholesterol levels of the underweight, normal weight, and obese groups were $51.92{\pm}9.39mg/dL$, $59.20{\pm}13.53mg/dL$, and $43.00{\pm}8.98mg/dL$, respectively, showing that the obese subjects had significantly lower HDL-cholesterol levels as compared to the subjects in the other groups (p<0.05). The HDL-C/LDL-C ratios of the underweight ($0.52{\pm}0.45$) and normal weight ($0.59{\pm}0.23$) groups were higher than the ratio of the obese group ($0.41{\pm}0.06$). Total cholesterol were positively correlated with LDL-cholesterol (r=0.768, p<0.01), but triacylglycerol were adversely correlated with HDL-cholesterol. In conclusion, our results show that college-aged women in Seoul should be encouraged to amend their overall dietary habits, make a dietary plan that fits their individual needs, and maintain an effective exercise schedule.

• Journal of the Korean Society of Food Culture
• /
• v.1 no.3
• /
• pp.183-196
• /
• 1986

This study was designed to be link in the chain of the investigation on daily life and consciousness of longevous people in Korea, and to investigate the social life and daily life habit in the past of longevous people. The social life and daily life habit were surveyed on 379 subjects (male 121, female 258) of the aged who were above 80 years of age, from June to November in 1985. 1. 'Generally regular' in the rising time and bedtime between 40 and 60 years of longevous people had the highest figures of 81.8% and 63.1%, respectively. The longevous peoples of 59.4% got up by before 6 a.m., and 61.3% of these aged went to bed from 9 to 11 p.m. But there was no significant difference between male and female. 2. Of the occupation engaged in the longest term of longevous people, the self-management (86.3%) included farming, fishing and household affairs was the highest, whereas administrative position, small-scale management and white-collar worker were only 0.8%, 0.8% and 1.8%, respectively. Therefore, their work involved mainly physical labor (heavy 48.5%, light 47.2%), and mental work was only 2.8% of longevous people. It is believed that this fact was deeply related to the educational degree of them. 3. The longevous people of 58.3% retired from the occupation and household affairs abover 70 years of age, and especially 24.3% of them is including the aged above 80 years of age. 4. The longevous people of 57.2% were shared the role in the home after retirement from the occupation and household affairs, whereas 35.9% of them didn't share. Of the way in killing time in case having no role in the home, 'at home'(50.0%) was the highest, and decreased in the order of 'old people's home' (30.9%), 'ill in bed' (10.3%) and 'asylum for the aged' (8.8%). 5. The acquaintance frequency before retirement from the occupation and household affairs of longevous people showed in the order of 'wide' (38.5%), 'common' (38.0%) and 'narrow' (19.0%), and 56.5% of them had the acquaintance after retirement. 6. Only the longevous people of 38.5% had the hobby and recreation activities of 'more than once' after retirement from the occupation and household affairs, but 53.0% of them was none. Of the kinds of hobby and/or recreation, 'TV-watching' (79.2%) was the highest, and decreased in the order of 'talking with grandchild' (54.2 %), 'working at home' (35.4%), 'religion' (25.0%) and 'chess etc.' (18.1%).

• Journal of Astronomy and Space Sciences
• /
• v.20 no.2
• /
• pp.109-122
• /
• 2003

To examine the causal relationship between geomagnetic storm and substorm, we investigate the correlation between dispersionless particle injection rate of proton flux observed from geosynchronous satellites, which is known to be a typical indicator of the substorm expansion activity, and Dst index during magnetic storms. We utilize geomagnetic storms occurred during the period of 1996 ~ 2000 and categorize them into three classes in terms of the minimum value of the Dst index ($Dst_{min}$); intense ($-200nT{$\leq$}Dst_{min}{$\leq$}-100nT$), moderate($-100nT{\leq}Dst_{min}{\leq}-50nT$), and small ($-50nT{\leq}Dst_{min}{\leq}-30nT$) -30nT)storms. We use the proton flux of the energy range from 50 keV to 670 keV, the major constituents of the ring current particles, observed from the LANL geosynchronous satellites located within the local time sector from 18:00 MLT to 04:00 MLT. We also examine the flux ratio ($f_{max}/f_{ave}$) to estimate particle energy injection rate into the inner magnetosphere, with $f_{ave}$ and $f_{max}$ being the flux levels during quiet and onset levels, respectively. The total energy injection rate into the inner magnetosphere can not be estimated from particle measurements by one or two satellites. However, the total energy injection rate should be at least proportional to the flux ratio and the injection frequency. Thus we propose a quantity, “total energy injection parameter (TEIP)”, defined by the product of the flux ratio and the injection frequency as an indicator of the injected energy into the inner magnetosphere. To investigate the phase dependence of the substorm contribution to the development of magnetic storm, we examine the correlations during the two intervals, main and recovery phase of storm separately. Several interesting tendencies are noted particularly during the main phase of storm. First, the average particle injection frequency tends to increase with the storm size with the correlation coefficient being 0.83. Second, the flux ratio ($f_{max}/f_{ave}$) tends to be higher during large storms. The correlation coefficient between $Dst_{min}$ and the flux ratio is generally high, for example, 0.74 for the 75~113 keV energy channel. Third, it is also worth mentioning that there is a high correlation between the TEIP and $Dst_{min}$ with the highest coefficient (0.80) being recorded for the energy channel of 75~113 keV, the typical particle energies of the ring current belt. Fourth, the particle injection during the recovery phase tends to make the storms longer. It is particularly the case for intense storms. These characteristics observed during the main phase of the magnetic storm indicate that substorm expansion activity is closely associated with the development of mangetic storm.

• Journal of Korea Technology Innovation Society
• /
• v.10 no.1
• /
• pp.73-97
• /
• 2007

R&D into future technologies should be conducted in conjunction with technological innovation strategies that are linked to corporate survival within a framework of information and knowledge-based competitiveness. As such, future technology strategies should be ensured through open R&D organizations. The development of future technologies should not be conducted simply on the basis of future forecasts, but should take into account customer needs in advance and reflect them in the development of the future technologies or services. This research aims to select as segmentation variables the customers' attitude towards accepting future telecommunication technologies and their value orientation in their everyday life, as these factors wilt have the greatest effect on the demand for future telecommunication services and thus segment the future telecom service market. Likewise, such research seeks to segment the market from the stage of technology R&D activities and employ the results to formulate technology development strategies. Based on the customer attitude towards accepting new technologies, two groups were induced, and a hierarchical customer segmentation model was provided to conduct secondary segmentation of the two groups on the basis of their respective customer value orientation. A survey was conducted in June 2006 on 800 consumers aged 15 to 69, residing in Seoul and five other major South Korean cities, through one-on-one interviews. The samples were divided into two sub-groups according to their level of acceptance of new technology; a sub-group demonstrating a high level of technology acceptance (39.4%) and another sub-group with a comparatively lower level of technology acceptance (60.6%). These two sub-groups were further divided each into 5 smaller sub-groups (10 total smaller sub-groups) through two rounds of segmentation. The ten sub-groups were then analyzed in their detailed characteristics, including general demographic characteristics, usage patterns in existing telecom services such as mobile service, broadband internet and wireless internet and the status of ownership of a computing or information device and the desire or intention to purchase one. Through these steps, we were able to statistically prove that each of these 10 sub-groups responded to telecom services as independent markets. We found that each segmented group responds as an independent individual market. Through correspondence analysis, the target segmentation groups were positioned in such a way as to facilitate the entry of future telecommunication services into the market, as well as their diffusion and transferability.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.3
• /
• pp.516-526
• /
• 2004

Polymerization shrinkage of photoinitiation type composite resin cause several clinical problems. The purpose of this study was to evaluate the shrinkage strain stress, linear polymerization shrinkage, compressive strength and microhardness of recently developed composite resins. The composite resins were divided into four groups according to the contents of matrix and filler type. Group I : $Denfil^{TM}$(Vericom, Korea) with conventional matrix, Group II : $Charmfil^{(R)}$(Dentkist, Korea) with microfiller and nanofller mixture, Group III : $Filtek^{TM}$ Z250(3M-ESPE, USA) TEGDMA replaced by UDMA and Bis-EMA(6) in the matrix, and Group IV : $Filtek^{TM}$ Supreme(3M-ESPE, USA) using pure nanofiller. Preparation of acrylic molds were followed by filling and curing with light gun. Strain gauges were attached to each sample and the leads were connected to a strainmeter. With strainmeter shrinkage strain stress and linear polymerization shrinkage was measured for 10 minutes. The data detected at 1 minute and 10 minutes were analysed statistically with ONE-way ANOVA test. To evaluate the mechanical properties of tested materials, compressive hardness test and microhardness test were also rendered. The results can be summarized as follows : 1. Filling materials in acrylic molds showed initial temporary expansion in the early phase of polymerization. This was followed by contraction with the rapid increase in strain stress during the first 1 minute and gradually decreased during post-gel shrinkage phase. After 1 minute, there's no statistical differences of strain stress between groups. The highest strain stress was found in group IV and followed by group III, I, II at 10 minutes-measurement(p>.05). In regression analysis of strain stress, group III showed minimal inclination and followed by group II, I, IV during 1 minute. 2. In linear polymerization shrinkage test, the composite resins in every group showed initial increase of shrinkage velocity during the first 1 minute, followed by gradually decrease of shrinkage velocity. After 1 minute, group IV and group III showed statistical difference(p<.05). After 10 minutes, there were statistical differences between group IV and group I, III(p<.05) and between group II and group III(p<.05). In regression analysis of linear polymerization shrinkage, group II showed minimal inclination and followed by group IV, III, I during 1 minute. 3. In compressive strength test, group III showed the highest strength and followed by group II, IV, I. There were statistical differences between group III and group IV, I(p<.05). 4. In microhardness test, upper surfaces showed higher value than lower surfaces in every group(p<.05).

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.5-7
• /
• 1974

1. This study indicates that above the fiber saturation point the drying rate can be increased with increasing the velocity of the air circutation, i.e., the drying rate of sample boards is proportional to the air velocity, but below the fiber saturation point, the effect of the velocity of air circulation is very low as shown in Figs. 1 and 2. 2. Under the controlled temperature and humidity in the kiln, the more the sample boards have moisture, the higher drying rate of it can be obtained. In other words, this means that even though in the case of drying various moisture content of wood, at the final drying stage, approximately the same percentage of moisture content of wood can be secured by employing the higher velocity of air circulation. 3. This study shows that the rate of drying in kiln changes distinctly at the fiber saturation point, i, e., above the fiber saturation point, the drying curve shows concave aginst the X axsis, but below the fiber saturation point, in the range from 30 percent of moisture content to 20 percent of moisture content, the curve shows convex as shown in Fig. 3. As the drying progresses, however, the drying curve shows concave again below 20 percent of moisture content. This means that inflection point of drying curve may be located clearly at the fiber saturation point, i.e., 30 percent of moisture content. As mentioned above, the 30 percent of moisture content of wood at which the inflectional point appears can be recognized as a critical point, i. e., the fiber saturation point at which all free water was removed from wood. The existence of inflectional point indicates that the evaporation of hygroscopic water in a cell wall is more difficult than the evaporation of free water in a cell cavity and the minor space of cell wall. The convex curve in the range of moisture content from 30 percent to 20 percent means that the evaporation of capillary condensed water has a tendency of the same rates of drying approximately, but as approaching to the 20 percent of moisture, the transfusion of moisture from wood becomes difficult because of having less moisture in cell wall. Below 20 percent of moisture content, the drying curve shows concave again, which means that it is difficult to remove the moisture located nearer to the surface of cellulose molecules and the surface bound water. These relations were revealed in Fig. 4. In comparison AC curve which does not have the two inflection points with BD curve which has two inflection points, i.e., Band D, they are mentioned already, by existence of the inflection points, the curve BD shows that the change of drying rate in the interval from 20 percent of moisture content to 30 percent of moisture content is not greater than in the case of the curve AC in the same interval. At the inflection point of 30 percent of moisture content, it can be noticed that the changing of the drying rate is very conspicuous. This phenomenon also can be recognized, as it is noticed by the Fig. 3, the drying rate from green to 30 percent of moisture content is very great. But the inclination of the curve is very slow from 30 percent of moisture content to 20 percent of moisture content, i.e., the inclination of the curve becomes almost horizontal lines. Acknowledgments Gratitude is expressed to Fred E. Dickinson, Professor of 'Wood Technology, School of Natural Resources, University of Michigan, USA for his suggestion to carry out this study.

• Restorative Dentistry and Endodontics
• /
• v.32 no.2
• /
• pp.138-150
• /
• 2007

The purpose of this study was to evaluate the difference of surface roughness of composite resin according to composite resin type, polishing methods, and use of resin sealant. Two hundred rectangular specimens, sized $8{\times}3{\times}2mm$, were made of Micro-new (Bisco, Inc., Schaumburg, IL, U.S.A) and Filtek Supreme (3M ESPE Dental Products, St. Paul, MN, U.S.A.), and divided into two groups; Micronew-M group, Filtek Supreme-S group. Specimens for each composite group were subdivided into five groups by finishing and polishing instruments used; M1 & S1(polyester strip), M2 & S2 (Sof-Lex disc), M3 & S3 (Enhance disc and polishing paste), M4 & S4(Astropol) and M5 & S5 (finishing bur), Polished groups were added letter B after the application of resin surface sealant (Biscover), eg, M1B and S1B. After specimens were stored with distilled water for 24hr, average surface roughness (Ra) was taken using a surface roughness tester. Representative specimens of each group were examined by FE-SEM (S-4700: Hitachi High Technologies Co., Tokyo, Japan). The data were analysed using paired t-test, ANOVA and Duncan's tests at the 0.05 probability level. The results of this study were as follows ; 1. The lowest Ra was achieved in all groups using polyester strip and the highest Ra was achieved in M5, S5 and M5B groups using finishing bur. On FE-SEM, M1 and S1 groups provided the smoothest surfaces, M5 and S5 groups were presented the roughest surfaces and voids by debonding of filler on the polished specimens. 2. There was no significant difference in Ra between Micronew and Filtek Supreme before the application of resin sealant, but Micronew was smoother than Filek Supreme after the application of resin sealant. 3. There was significant corelation between Ra of type of composite resin and polishing methods before the application of resin sealant (p=0.000), but no significant interaction between them after the application of resin sealant. On FE-SEM, most of composite resin surfaces were smooth after the application of resin sealant on the polished specimens. 4. Compared with before and after the application of resin sealant in group treated in the same composite and polishing methods, Ra of M4B and M5B was statistically lower than that of M4 and M5, and S5B was lower than that of S5, respectively (p<0.05). In conclusion, surface roughness by polishing instruments was different according to type of composite resin. Overall, polyester strip produced the smoothest surface, but finishing bur produced the roughest surface. Application of resin sealant provided the smooth surfaces in specimens polished with Enhance, Astropol and finishing bur, but not provided them in specimens polished with Sof-Lex disc.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.33 no.3
• /
• pp.38-49
• /
• 2015

This study aims to contemplated spatial recognition in Soswaewon Garden through garden visitors poetry. It was content analysis in poetry and extract frequency from words based on relationship of author. The results were as follows. First, relationship of authors who wrote Soswaewon Garden poetry was formed in companionship. In the Yang, San-Bo(梁山甫), poetry was written by Song, Soon(宋純), Kim, Un-Geo(金彦据) and Kim, In-Hu(金麟厚) as the central figure. Especially Kim, In-Hu was playing an important role in Soswaewon Garden poetry. He was wrote many of poetry and keep friends with Yang, Ja-Jeong(梁子渟) too. In the Yang, Ja-Jung, relationship of previous generation was sustained. In addition, Ko, Gyeong-Myeong(高敬命) and Kim, Seong-Won and Jeong, Chul(鄭澈) is more closely related than others. Because blood relationship by marriage. In the Yang, Jin-Tae(梁晋泰), He formed a relationship with a celebrity and attend to international activity. Since then Yang, Jin-Tae periord, Yang, Gyeong-Ji(梁敬之) and Yang, Chae-Ji(梁采之) formed relationship of previous generation was sustained. And surrounding people was written poetry as hold a banquet. Second, plant and ornament is a popular object for writing poetry. Bamboo grove and Fine tree with a high frequency of plant element in poetry. Bamboo grove is a typical species of trees in Soswaewon Garden. It was enclosed the Soswaewon Garden. Fine tree was often used target of poetry as a single tree. Meanwhile, ornament of the wall has been used most frequently. Descendants wrote a poem to see it because Kim, In-Hu's poetry was left. This phenomenon is involves respect for the ancient sages with high frequency. In addition, behavior of viewing the landscape was mainly appeared. Third, spatial recognition of Soswaewon Garden can be divided into landscape cognition, behavior cognition and emotional cognition. In a aspect of landscape cognition, early Soswaewon Garden was recognized as a pavilion. That was used garden name to 'Soswaewon Garden' since Yang, Ja-Jung's period. That is to say, Soswaewon Garden expanded from pavilion area surrounded by trees into the whole appearance is equipped garden area. Behavior cognition was consisting drink and enjoys a landscape. In the Yang, San-Bo, authors enjoyed drinking and viewing a landscape besides walking, writing poetry, viewing the moon. But after Yang, San-Bo's period other than drinking and enjoy a landscape has appeared a low frequency. These results were changed from internal place to blood relationship into external place to companionship. In the Yang, San-Bo's emotional cognition was sorrow and yearning about leave to Soswaewon Garden with an idly atmosphere. Pleasant emotion was sustained all generation. And emotion of respect for the ancient sages was appeared since Yang, Cheon-un.

• Proceedings of the KOR-BRONCHOESO Conference
• /
• 1981.05a
• /
• pp.6-7
• /
• 1981

With the improvement of living standard and educational level of the people, there is an increasing awareness about the dangers of toxic substances and lethal drugs. In addition to the above, the governmental control of these substances has led to a progressive decrease in the accidents with corrosive substances. However there are still sporadic incidences of suicidal attempts with the substances due to the unbalance between the cultural development in society and individual emotion. The problem is explained by the fact that there is a variety of corrosive agents easily available to the people due to the considerable industrial development and industrialization. Salzen(1920), Bokey(1924) were pioneers on the subject of the corrosive esophagitis and esophageal stenosis by dilatation method. Since then there had been a continuing improvement on the subject with researches on various acid(Pitkin, 1935, Carmody, 1936) and alkali (Tree, 1942, Tucker, 1951) corrosive agents, and the use of steroid (Spain, 1950) and antibiotics. Recently, early esophagoscopic examination is emphasized on the purpose of determining the way of the treatment in corrosive esophagitis patients. In order to find the effective treatment of such patients in future, the authors selected 96 corrosive esophagitis patients who were admitted and treated at the ENT department of Severance hospital from 1971 to March, 1981 to attempt a clinical study. 1. Sex incidence……male: female=1 : 1.7, Age incidence……21-30 years age group; 38 cases (39.6%). 2. Suicidal attempt……80 cases(83.3%), Accidental ingestion……16 cases (16.7%). Among those who ingested the substance accidentally, children below ten years were most numerous with nine patients. 3. Incidence acetic acid……41 cases(41.8%), lye…20 cases (20.4%), HCI……17 cases (17.3%). There was a trend of rapid rise in the incidence of acidic corrosive agents especially acetic acid. 4. Lavage……57 cases (81.1%). 5. Nasogastric tube insertion……80 cases (83.3%), No insertion……16 cases(16.7%), late admittance……10 cases, failure…4 cases, other……2 cases. 6. Tracheostomy……17 cases(17.7%), respiratory problems(75.0%), mental problems (25.0%). 7. Early endoscopy……11 cases(11.5%), within 48 hours……6 cases (54.4%). Endoscopic results; moderate mucosal ulceration…8 cases (72.7%), mild mucosal erythema……2 cases (18.2%), severe mucosal ulceration……1 cases (9.1%) and among those who took early endoscopic examination; 6 patients were confirmed mild lesion and so they were discharged after endoscopy. Average period of admittance in the cases of nasogastric tube insertion was 4 weeks. 8. Nasogastric tube indwelling period……average 11.6 days, recently our treatment trend in the corrosive esophagitis patients with nasogastric tube indwelling is determined according to the finding of early endoscopy. 9. The No. of patients who didn't given and delayed administration of steroid……7 cases(48.9%): causes; kind of drug(acid, unknown)……12 cases, late admittance……11 cases, mild case…9 cases, contraindication……7 cases, other …8 cases. 10. Management of stricture; bougienage……7 cases, feeding gastrostomy……6 cases, other surgical management……4 cases. 11. Complication……27 cases(28.1%); cardio-pulmonary……10 cases, visceral rupture……8 cases, massive bleeding……6 cases, renal failure……4 cases, other…2 cases, expire and moribund discharge…8 cases. 12. No. of follow-up case……23 cases; esophageal stricture……13 cases and site of stricture; hypopharynx……1 case, mid third of esophagus…5 cases, upper third of esophagus…3 cases, lower third of esophagus……3 cases pylorus……1 case, diffuse esophageal stenosis……1 case.