• Journal of Korean Society of Steel Construction
• /
• v.26 no.3
• /
• pp.241-250
• /
• 2014

The purpose of this study is to propose structural technologies on the light-weight composite floor systems in the unit modular and to evaluate structural performance of the composite floor through flexural experiments. The flexural experiments were carried out on total nine specimens(each three type in shape) using steel flat deck and truss deck. From the results of test, all specimens showed the same failure patterns which exhibited deflection at the center of the specimens due to flexural deformation before concrete crushing at the upper of specimens. Also, we know that the proposed floors satisfied in serviceability and would be safe sufficiently. The ratio of experimental yield load by theoretical nominal load was the distribution of 0.86 to 1.27 with an average 1.04. Coefficient of variation in distribution showed good agreement.

• Journal of Science and Technology Studies
• /
• v.1 no.1 s.1
• /
• pp.235-259
• /
• 2001

This study investigates a variety of dysfunctions and dynamics accompanied with the spread of advanced technology, and predicts the developmental directions of future uncertain society. There are, further, proper countermeasures against dysfunctions discussed. First, different theoretical paradigms concerned with the relationship between seience/technology and society would be comparatively analyzed, and their techno-social implications would be examined. Next, the latest trend of bio-technology and information technology, especially the trend of combination of bio- and information technology, appeared in the progress of Human Genome Project, would be considered. Thirdly, techno-social dysfunctions and far-reaching effects following the development of high-technologies would be analyzed, and realistic alternative plans would be suggested. Through this study, we come to a conclusion that, in order to reduce techno-social dysfunctions to a minimum and enhance their eufunctions, not only 'human' control over technological development should be guaranteed, but also action plan for bridging social gaps should be prepared. In addition, fluent communication and mutual understanding of all concerned, particularly between researcher community, government, and civic sector are required.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.11
• /
• pp.1205-1216
• /
• 2015

Since concentration of greenhouse gas increases continuously from human's fossil fuel use, urbanization, and cultivation, it is trend that climate change is appearing. In Addition, in 20th century, occurrence of disaster is accidental and huge, and damage level also increases gradually. Therefore, in order to preserve the territory and to protect people's life and property against new type disasters, disaster detection satellite (payloads) development is required urgently. In this paper, we conduct a research and development for the prompt preemptive action when occurred a disaster, in particularly, about the disaster observation optimized at Korea's geographical features for the irregular future disasters. For the payload design which is specialized detect disasters, we create a tech tree of satellite imagery applications based 10 disaster types, and analyze the satellite sensor technologies referred to Landsat-8, Worldview-3 and ALOS-2.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.218-225
• /
• 2021

The purpose of this study is to present a rational analytical method for predicting the behavioral characteristics from crack occurrence to fracture for a one-way CFRP grid reinforced concrete slab specimen. A total of four specimens were selected by Zhang et al.(2004) as the main experimental variables for CFRP grid amount, material properties and loading method. Analysis was performed through the Nonlinear Finite Element analysis program(RCAHEST), which applied the newly modified constitutive relational equations by the author. The mean and coefficient of variation for maximum moment from the experiment and analysis results was predicted 1.38 and 7 %. The mean and coefficient of variation for displacement corresponding maximum moment from the experiment and analysis results was predicted 1.41and 9.8 %. The prediction results for the behavioral characteristics from crack occurrence to fracture were verified and evaluated. It is judged that additional research is needed to secure various experimental results and to develop a more reliable analytical method.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.14 no.5
• /
• pp.121-133
• /
• 2004

In [15,16], Okeya and Sakurai showed that the randomized addition-subtraction chains countermeasures [18] are vulnerable to SPA attack. In this paper, we show that Okeya and Sakurai's attack algorithm [15,16] has two latent problems which need to be considered. We further propose new powerful concrete attack algorithms which are different from [15,16,19]. From our implementation results for standard 163-bit keys, the success probability for the simple version with 20 AD sequences is about 94% and with 30 AD sequences is about 99%. Also, the success probability for the complex version with 40 AD sequences is about 94% and with 70 AD sequences is about 99%.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.360-360
• /
• 2020

조립식 빗물침투형 저류블록은 우수유출 저감시설로, 황토 및 친환경 무기질 결합재를 이용하여 제작한 고강도 투수성 블록의 적층 및 요철에 의한 끼움식 조립에 의해 형성된 공간에 빗물을 저류하고, 저장된 빗물은 시간이 지남에 따라 지반으로 침투시키는 우수유출 저감용 빗물관리시설로, 집중강우 시 유출수가 발생하는 해당지역에 분산식으로 설치하여 국지적 호우 발생에 대처할 수 있으며, 지속적인 침투를 통한 지하수위 확보 및 가뭄현상의 저감은 물론, 미기후 조성과 건전한 물순환 구조 형성에 이바지하는 빗물관리기술이다. 본 기술은 집중형 대규모 빗물저류조의 적용상의 문제점과 단순저류의 한계성을 극복하고, 기존 침투시설의 낮은 침투능을 증대시키고자 저류기능과 침투기능을 동시에 확보하여 집중호우시 빠른 침투저류능을 향상시킨 조립식 빗물침투형 저류시설이다. 보다 구체적으로는 집중강우에 대한 방재적 측면과 함께 가뭄으로 발생하는 지하수위 저하 등에 친환경적으로 대응하기 위한 복합적인 빗물관리 기술로서, 빗물 유출저감과 함께 물순환 회복 및 저영향개발을 위한 각 지자체의 지침과도 부합될 수 있다. 또한, 콘크리트 제품의 환경적 문제점과 플라스틱 제품의 낮은 물성을 극복하였고, 시공 시에는 보다 현장상황에 맞게 가변적 형태로 적용이 가능한 단순조립 적층공법으로 공기단축에 탁월한 장점이 있으며, 유지관리 시에는 별도의 동력이 요구되지 않는 형태로 개발하였다. 조립식 빗물침투저류블록의 구조체를 이루는 단위 블록유닛은 투수성 소재로 제작되며, 상하부가 개방되어 있고 사각형의 내부에 힘을 받는 격벽과 전후벽이 상호 대응되는 요철로 형성되어 있으며, 단위블록 유닛 다수개가 수직수평으로 연속적으로 조립되어 규모의 제한, 형태의 제한이 없는 구조물 형성이 가능하다. 본 구조체의 저류공극율은 80%이상 확보 가능하며, 또한 블록자체의 투수율이 0.83mm/sec로서 순모래나 순자갈의 포화투수계수보다 투수율이 높아 침투저류 효율성이 높으며 시공 후 상부 토지는 자유롭게 활용 가능하다. 본 조립식 빗물 침투형 저류블록을 이용하여 저영향개발 계획, 우수유출 저감대책 수립, 빗물관리시설 계획시 기존의 시설들에 비하여 경제적, 효율적인 설계가 가능하다.

• Journal of the Korean Society of International Agriculture
• /
• v.31 no.4
• /
• pp.378-383
• /
• 2019

To determine whether FT-IR spectral analysis based on multivariate analysis for whole cell extracts can be used to discriminate papaya at metabolic level. FT-IR spectral data from leaves were analyzed by principal component analysis (PCA), partial least square discriminant analysis (PLS-DA) and hierarchical clustering analysis (HCA). FT-IR spectra confirmed typical spectral differences between the frequency regions of 1,700-1,500, 1,500-1,300 and 1,100-950 cm^-1, respectively. These spectral regions were reflecting the quantitative and qualitative variations of amide I, II from amino acids and proteins (1,700-1,500 cm^-1), phosphodiester groups from nucleic acid and phospholipid (1,500-1,300 cm^-1) and carbohydrate compounds (1,100-950 cm^-1). The result of PCA analysis showed that papaya leaves could be separated into clusters depending on different growth temperature. In this case, showed discrimination confirmed according to metabolite content of growth condition from papaya. And PLS-DA analysis also showed more clear discrimination pattern than PCA result. Furthermore, these metabolic discrimination systems could be applied for rapid selection and classification of useful papaya cultivars.

• Applied Microscopy
• /
• v.35 no.3
• /
• pp.135-152
• /
• 2005

Prefrontal cortex is a psychological and metaphysical cortex, which deals with feeling, memory, planning, attention, personality, etc. And it also integrates above-mentioned events with motor control and locomotor activities. Prefrontal cortex works as a highest CNS center, since the above mentioned functions are very important for one's successful life, and further more they are upgraded every moments through memory and learning. Many of these highest functions are supposed to be generated via forebrain basal nuclei (caudate nucleus, fundus striati nucleus, accumbens septi nucleus, septal nucleus, etc.). In this experiment, prefrontal efferent terminals within basal forebrain nuclei were ultrastructurally studied. Spraque Dawley rats, weighing $250{\sim}300g$ each, were anesthetized and their heads were fixed on the stereotaxic apparatus (experimental model, David Kopf Co.). Rats were incised their scalp, perforated a 3mm-wide hole on the right side of skull at the 11mm anterior point from the frontal O point (Ref. 13, Fig. 1), suctioned out the prefrontal cortex including cortex of the frontal pole, with suction instrument. Two days following the operations, small tissue blocks of basal forebrain nuclei were punched out, fixed in 1% glutaraldehyde-1% paraformaldehyde solution followed by 2% osmium tetroxide solutions. Ultrathin sections were stained with 1% borax-toluidin blue solution, and the stained sections were obserbed with an electron microscope. Degenerating axon terminals were found within all the basal forbrain nuclei. Numbers of degenerated terminals were largest in the caudate nucleus, next in order, in the fundus striati nucleus, in the accumbens septi nucleus, and the least in the septal nucleus. Only axospinous terminals were degenerated within the caudate nucleus and the fundus striati nucleus, and they showed the characters of striatal motor control system. Axodendritic and axospinous terminals were degenerated within the accumbens septi nucleus and the lateral septal nucleus, and they showed the characters of visceral limbic system. Prefrontal role in integrating the limbic system with the striatal system, en route basal forebrain nuclei, was discussed.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.98-98
• /
• 2012

최근 국내외에서 첨단 기능성 섬유에 대한 소비자들의 관심이 높아지면서 다양한 분야에서 기능성 소재들이 개발되고 있다. 특히 기능성 스포츠웨어 시장에서는 계절의 경계를 넘어 야외 활동 중에 사용할 수 있는 제품에 대한 요구가 증가되고 있는데, 날씨가 매우 덥고 햇살이 뜨거운 것에서부터, 얼음처럼 차갑고 추운 것까지 가지각색 인 경우가 있을 수 있다. 이러한 변화무쌍한 날씨에 쾌적한 활동을 하기 위해서는 외부 온도변화에 대응하여 몸을 보호하고 자연환경에 맞설 수 있는 의복의 필요성이 부각되고 있다. 본 연구에서 개발하고자 하는 지능형 체온조절 섬유는 정적상태에서는 보온성과 적외선을 방출을 통한 자가 발열기능을 부여하고, 동적상태에서는 태양열 증폭기능과 운동량에 따른 흡습발열의 기능을 통하여 자연환경과 의복환경의 변화에 대응할 수 있는 스포츠웨어 제품이다. 따라서 보온성이 우수한 PP, acrylate 원사 등을 이용하여 복합 방적사 설계 및 생산을 최적화였다. 또한 흡습발열 성능이 향상된 섬유구조체를 설계하여 개발 원사 구성에 따라 보온 발열 기능성 부여 방법을 달리하여 최적의 성능을 이끌어내는 제품을 개발하고자 하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.160-164
• /
• 2003

LCD를 TV 향으로 적용하기 위해서는 몇 가지 해결해야만 하는 문제가 있으며, 이중 하나가 동화상 재생시에 발생하는 잔상현상의 해결이다. LCD는 기존의 CRT와 같은 불연속 자발광 소자가 아니라, 연속수광소자로서, 잔상현상이 치명적인 약점으로 나타난다. 기종의 Monitor 대응품에서는 실제로 Monitor를 통해서 사용자가 관찰하는 이미지 정보가 정지화상 중심으로 구성되어 있기 때문에 문제가 되지 않았으나, TV의 경우 연속적인 동화상만을 취급하고 있어, 잔상현상의 해결 없이는 TV 향 제품에 적용할 수 없다. 따라서 본 연구에서는 잔상현상을 근본적으로 없애기 위해서 LCD를 CRT와 같이 불연속적의 분절적 이미지로 구동하는 방법을 실험하였으며, VIDEO 입력 신호에 대해서 16.7msec의 1Frame을 기준으로 점등 구간과 비점등 구간을 6:4로 나누어 BL(Back Light)을 점멸하는 방법을 구현하였다. 또한 종래의 CCFL(cold Cathod Flourescent Lamp)로는 점멸 속도에 대한 대응이 불가하므로, 이를 해결하기 위해서 광원의 형광체에 대해서 잔광시간특성의 개선도 동시에 실시하였다. 실험 결과 육안 및 사진촬영에서 잔상없는 화면을 얻을 수 있었으며, 응답파형 측정 결과 CRT 측정시와 마찬가지로 분절적인 이미지의 생성이 가능한 것을 알 수 있었다.