• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.721-728
• /
• 2009

Equal/unequal 4-way power divider suitable for satellite communication using SIW technology is presented in this paper. The control of positions of guiding posts provides equal or unequal power division ratios by maintaining the width of the SIW unchanged. In addition, the detailed descriptions for the proposed power divider include the general characteristics of radial waveguide, feeding part using coaxial cable, simple SIW structure, power-guiding posts, and transition for measurement. The comparison between the simulated and measured data shows a good agreement at a center frequency of 10 GHz. The measured input impedance bandwidths for equal and unequal power divisions are about 2.1 GHz and 3 GHz under the condition of less than VSWR 2:1, respectively.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.430-436
• /
• 2006

Polarization-independent $Ti:LiNbO_3\;2{\times}2$ optical add/drop multiplexer for the 1550nm wavelength region is fabricated. The device consists of two input waveguides, two polarization beam splitters. two polarization conversion/electrooptic tuning waveguide sections, and two output waveguides. The single mode channel waveguides for both TE and TM polarizations are fabricated on a x-cut $Ti:LiNbO_3$substrate by Ti diffusion. Spectral section is based on phase-matched polarization conversion due to shear strain induced by a thick $SiO_2$ grating overlay film. An applied voltage tunes the device by changing the waveguide birefringence, hence the optical wavelength at which most efficient polarization conversion occurs. Tuning rate of 0.094nm/V with a maximum range of 17nm has been obtained. The nearest side-lobe is about 8.2dB. The FWHM is 3.72nm.

• Journal of the Korea Knowledge Information Technology Society
• /
• v.12 no.4
• /
• pp.539-550
• /
• 2017

In this paper, we designed, fabricated and tested an UHF band cylindrical dipole array antenna. In the proposed antenna, cylindrical dipoles were vertically arranged in four stages. A parallel structure feeding circuit was installed inside the cylindrical dipole and mounted so as to be broadband matching. The feeding circuit was installed at the center of the cylindrical dipole to optimize the gain flatness characteristic of the azimuth direction omnidirectional radiation pattern. Minimizing the difference between the signals branched from the feeding circuit and realizing the symmetry of the radiation pattern. The required specifications are more than 11.2% bandwidth in UHF band, above 6dBi antenna gain, standing wave ratio of 2:1 or less, less than ${\pm}1dB$ gain flatness in azimuth radiation pattern, more than 13 degrees in elevation radiation pattern of 3dB beamwidth. We confirmed the possibility of implementation through M&S and verified the result of M&S through production and testing. The test results are 11.2% bandwidth in the UHF band, 6.30 to 8.31 dBi gain, 1.53:1 standing wave ratio or less, within ${\pm}0.2dB$ gain flatness in the azimuth radiation pattern, elevation radiation pattern of 3dB beam width was 15.62 to 15.84 degrees. The test result meets all requirements specifications.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.12
• /
• pp.1712-1718
• /
• 2013

This paper proposes a compact dual-band 3-way power divider that helps lowering the weight of a transceiver for the L-band or multi-purpose satellite communication. Instead of the multi stages or tapering which ends up with loss accumulation and size-growth, the non-linear dispersive phases from the metamaterial CRLH(composite right and left-handed) properties are obtained by the accurate formulation and implemented by the short transmission line segments. Firstly, the CRLH dual-band two-way unequal power divider and equal power divider are separately designed. And then, the input of the two-way equal power divider is plugged in the output port of the unequal one, and the entire geometry is slightly adjusted for the desirable performance. The circuit analysis and full-wave simulation are used to predict the frequency responses and validated by the measurement of the prototype. Besides, the size-reduction effect is addressed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.998-1004
• /
• 2002

This paper reports a design of feedforward linear power amplifier using pilot tone for IMT-2000 band repeaters accepting multi-carrier. As this time pilot tone is applied to the circuit differently from the existing method. Only one pilot tone is used in both 1-st loop(IMD abstraction loop) and 2-nd loop(IMD cancellation loop) to cancell IMD signals automatically according to variation of frequency or power level of input signals. As an experiment, in range of 2110 MHz - 2170 MHz at LPA output power of $20 W_{avg}$, IMD characteristics of over 20 dB was improved maintaining below -60 dBc considering respective 20 MHz. Therefore the supposed feedforward linear power amplifier can be used for linear power amplifier in IMT-2000 band repeaters.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.32-37
• /
• 2002

Passive polarization mode splitters at λ= 1.55 ${\mu}{\textrm}{m}$ were designed and fabricated based on Ti:x-cut LiNbO$_3$ single-mode optical waveguide and two-mode interference theory. The splitting ratio with waveguide width 8 ${\mu}{\textrm}{m}$, branching angle 0.55$^{\circ}$ and interfering length 470 ${\mu}{\textrm}{m}$ showed 16.18 dB, 21.25 dB for TE and TM input polarization modes, respectively. Polarization cross-talk of -16.28 dB and -21.28 dB for TE and TM modes was achieved. Total insertion losses of 2.24 dB/cm (TE) and 2.41 dB/cm (TM) were also measured. The devices operated nearly wavelength independently over a range or 30 nm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.9A
• /
• pp.685-696
• /
• 2009

The requirements of the NGA are to provide broader bandwidth, higher splitting ratio, and longer reach than those of the current FTTH. In the TDMA PON accounting for large percentage in the total FTTH, the increase in distance between the OLT and the ONU leads to the increase in propagation delay and in packet delay three times more than the propagation delay. It is because a packet arrived in the ONU is handled through bandwidth request, grant, and transmission. To reduce the increased packet delay, the OLT have to reduce the cycle time. However, it will cause increased overhead and reduced link efficiency. In this paper, we investigate several problems in TDMA PON when the subscriber access network extended to 60 or 100 Km reach as a NGA goal and provide a method that determines an optimal cycle time to satisfy QoS for delay sensitive traffics. In particular, we suggest a variable equalized round trip delay method and a variable cycle time method. It is shown that the former reduces the packet delay and the latter increase the link efficiency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.11
• /
• pp.1019-1022
• /
• 2016

In this paper, a 2~16 GHz GaN wideband power amplifier MMIC s designed and fabricated using the nonuniform power amplifier design technique that utilizes drain shunt capacitors to simultaneously provide each transistor with the optimum load impedance and phase balance between input and output transmission lines. The power amplifier MMIC chip that is fabricated using the $0.25{\mu}m$ GaN HEMT foundry process of Win Semiconductors occupies an area of $3.9mm{\times}3.1mm$ and shows a linear gain of larger than 12 dB and an input return loss of greater than 10 dB. Under a continuous-wave mode, it has a saturated output power of 36.2~38.5 dBm and a power-added efficiency of about 8~16 % in 2 to 16 GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.12
• /
• pp.1618-1623
• /
• 2019

In this paper, inductive couplers realizing broadband powerline communication (PLC) are fabricated using Fe-based nanocrystalline alloy and their performance is analyzed. As a result of the field tests using the distribution automation system (DAS), the couplers achieve comparatively excellent data communication in the principal frequency band of broadband PLC although there is a difference in communication rate depending on the presence or absence of a branch. In addition, it has been confirmed that the communication speed is maintained for a real-time transmission even in a high current environment although there is a difference in the transmission rate depending on the distance. Hence, it is considered that the inductive couplers can be used as a core device to realize the intelligent power network by exploiting them for the monitoring and remote controlling of the power plant equipments for the DAS located in the inaccessible areas.