• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.989-992
• /
• 2008

In this paper, we are presenting a case that integrates ultra high strength concrete(150MPa) with surface-exposed concrete. Ahead of the field application, we carried out laboratory experiment and B/P Test for a basic property of concrete(slump flow, air content, 50cm flow time, elapse time change and compression strength) and productivity. The next, we conducted Mock-up Test using simulation specimen to evaluate infilling, surface-finishing and hydration heat of concrete. We had satisfactory results for a basic property and hydration heat of concrete. However at the time of field application, it was occurred rupture of formwork because of high lateral pressure of concrete, and then formwork was reinforced and case-in-place time was adjusted. And regardless of low and high frequency vibration, it occurred to surface-pockmark. In case that applies ultra high strength concrete to surface-exposed concrete, we estimate that it is important of systematic management and improvement of construction.

• Journal of the Korea Concrete Institute
• /
• v.14 no.1
• /
• pp.92-99
• /
• 2002

This paper is Intended to investigate physical properties and surface glossing of exposed concrete incorporating granulated blast furnace slag(BS). According to test results there is no remarkable variations in fluidity and air content with increase of BS, but unit weight shows decline tendency Compressive strength at later age gains considerably due to potential hydraulicity reaction of BS. It shows that drying shrinkage increases. It is found that low W/B, surface coating and high BS content lead to favorable effects on the surface glossing of exposed concrete because of filling effects on the voids of the concrete. It is improved by about 7 ％ with increase every 10 ％ of BS content. The effects of form pannel kinds on the improvement of surface glossing are in order for acryl, fancy, steel and wood.

• Journal of the Korea Concrete Institute
• /
• v.16 no.1 s.79
• /
• pp.79-87
• /
• 2004

The qualify of lightweight aggregate made from waste PET bottle(WPLA) and the workability, the unit weight and strength property of concrete with WPLA were investigated for the purpose of recycling the waste PET bottles as lightweight concrete fine aggregate. This study indicated a good result that WPLA should be replaced with less than $50\%$ of natural fine aggregate. When WPLA was replaced with $50\%$ of natural fine aggregate, the specific gravity and water absorption of mixed fine aggregate were greatly reduced about 23 and $75\%$ respectively in comparison with those of river sand. The quality of WPLA affected on the properties of lightweight aggregate concrete. The workability of fresh concrete with WPLA(WPLAC) was improved with increasing the replacement ratio of WPLA and water cement ratio. Slump increasing ratio of the former showed about $45 {\~} 120\%$ because that a specific gravity of fine aggregate was decreased from 2.6 to 1.7. The unit weight of concrete with $75\%$ WPLA was decreased about $17\%$ in comparison with that of control concrete. Furthermore, the compressive strength of concrete with 25 and $50 \%$ WPLA at the age of 28 days increased higher than 30 MPa regardless with water cement ratio (W/C=45, 49 and $53\%$) of this study. Specific strength of concrete with $25\%$ WPLA, $15.11{\times}10^3 MPa{\cdot}m^3/kg$, was higher than that of contro concrete in water cement ratio of $49\%$. The compressive strength-splitting tensile strength ratio and compressive strength-modulus of elasticity ratio of WPLAC were similar to that of nomal lightweight aggregate concrete. This results showed a good estimation that WPLA will be able to recycled as a fine aggregate for lightweight concrete.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.52 no.3
• /
• pp.239-248
• /
• 2007

Although high nutritional values and continuous identification of important functional substances of soybean [Glycine max (L.) Merrill.] promote consumption of soybean products worldwide, informations on quality of brand soybean is not enough for consumers. Total of 100 brand soybeans [32 for soypaste and source, 45 black testa (lage), and 17 black testa (small) or medicinal soybean and beansprout soybean] were collected at supermarkets and several external quality factors were analyzed. Brand soybeans were marked with the environmental friendly and intimating words along with soybean (white or yellow), black soybean (black-, frost-, late frost-, green or inner-green-), medicinal soybean and beansprout soybean. Among 100 brand soybeans 30% was 1 kg package and 59% was 500 g package, difference between printed and actual weights of 70% brand soybeans was ${\pm}1%$ and weights of 2/3 of brand soybeans were higher than printed weight. Range of 100 seed weights of soypaste and source, black testa (large) and black testa (small) and beansprout soybeans were $23.7{\sim}47.8g$, $21.9{\sim}44.5g$ and $9.5{\sim}15.0g$, respectively. Although ranges of 100 seed weights of soypaste and source and black testa (large) soybeans were similar, 63% of soypaste and source were less than 29 g, while 78% of black testa (large) soybeans were higher than 30 g. Although average and highest percentages of seeds separated with 6.7 mm sieve were similar with 87.4% and 99.9% for soypaste and source soybean and 86.5% and 99.5% for black testa (large) soybean, respectively, the lowest percentages were 70.7% for soypaste and source soybean and 14.4% for black testa (large) soybean. When 100 seed weight was greater than 35 g, 90% of seeds were remained on 6.7 mm sieve. On the other hand 100 g weight and percentage of seeds remained on 6.7 mm sieve showed significantly positive correlations [r=0.7488** for soypaste and source soybean and r=0.7874** for black testa (large) soybean when 100 seed weight was $20{\sim}30g$. Based on hilum color and/or appearance, 76% of brand soybeans collected (more than 90% in yellow testa soybeans) were found to be mixed more than 10% with other cultivars or landraces. Foreign materials such as sand, piece of clothe, wood piece, dead insects, other soybeans were found in 20% of brand soybeans. Average test weight of brand soybeans was 762g $L^{-1}$ with a range of $645{\sim}820g\;L^{-1}$. Soybeans from local markets were as good as brand soybeans in 100 seed weight, uniformity of seeds, weight of foreign materials and test weight.

• Journal of the Korea Concrete Institute
• /
• v.23 no.5
• /
• pp.617-626
• /
• 2011

Seven post-tensioned lightweight concrete (LWC) beam specimens were tested under a symmetrical two-point top loading system. The parameters investigated were the amounts of mild longitudinal reinforcement and effective prestressing. The design compressive strength and dry density of the LWC tested were 30 MPa and 1,770 $kg/m^3$, respectively. Similar to post-tensioned normal weight concrete (NWC) beams, the crack propagation and stress increase of the unbonded tendons were significantly affected by the amounts of mild longitudinal reinforcement and effective prestressing. With the increase in the amounts of mild longitudinal reinforcement and effective prestressing, the serviceability and flexural capacity of the beams were enhanced whereas the stress increase in the unbonded tendons decreased. To control the crack width in post-tensioned LWC beams, a minimum amount of mild longitudinal reinforcement specified in ACI 318-08 provision is required. The flexural behavior of post-tensioned LWC beams and stress increase of the unbonded tendons could be rationally predicted by the proposed non-linear two-dimensional analysis. On the other hand, ACI 318-08 flexure provision was too conservative about the post-tensioned LWC beams.

• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.419-426
• /
• 2015

The purpose of this study is to investigate experimentally the optimum mix design and site application case of soil mixing wall (SMW) method which is cost-effective technique for construction of walls for cutoff wall and excavation support as well as for ground improvement before constructing LNG storage tank typed under-ground. Considering native soil condition in site, main materials are selected ordinary portland cement, bentonite as a binder slurry and also it is applied $1,833kg/m^3$ as an unit volume weight of native soil, Variations for soil mixing wall are as followings ; (1) water-cement ratio 4cases (2) mixing velocity (rpm) 3levels (3) bleeding capacity and ratio, compressive strength in laboratory and site application test. As test results, bleeding capacity and ratio are decreased in case of decreasing water-cement ratio and increasing mixing velocity. Required compressive strength (1.5 MPa) considering safety factors in site is satisfied with the range of water-cement ratio 150% below, and test results of core strength are higher than those of specimen strength in the range of 8~23% by actual application of element members including outside and inside in site construction work. Therefore, optimum mix design of soil mixing wall is proposed in the range of unit cement $280kg/m^3$, unit bentonite $10kg/m^3$, water-cement ratio 150% and mixing velocity 90rpm and test results of site application case are satisfied with the required properties.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.438-446
• /
• 2001

Recently, porous concrete has been used for the purpose of decreasing the load of earth environment. It consists solely of cement, water and uniform-sized coarse aggregate. And its fundamental properties will be considerably affected by the physical properties of aggregate because the aggregate occupies for the most part in its mix proportion. For such a reason, this study was carried out to investigate the influence of the sizes and kinds of aggregate for the fundamental properties of porous concrete. It showed that the fundamental properties of porous concrete were the similar value in all sizes of aggregate except in the case of using the 2.5∼5㎜ aggregate and were varied according to the kinds of aggregate. In particular, compressive strength of porous concrete using 2.5∼5㎜ aggregate was more higher than that using other aggregate, and its void ratio and coefficient of permeability was lower. And the maintenance capacity of permeability of porous concrete was varied by the sizes and the kinds of aggregate. In particular, it was greatly decreased in case of using the 2.5∼5㎜ aggregate. And unlike dynamic modulus of elasticity of ordinary concrete, that of porous concrete was very high value in early ages and was slowly increased after that time.

• Journal of the Korea Concrete Institute
• /
• v.28 no.5
• /
• pp.555-562
• /
• 2016

The objective of the present study is to evaluate the shear transfer capacity of transverse reinforcement at the concrete interfaces with smooth construction joint. The transverse reinforcing bars were classified into two groups: V-type for the arrangement perpendicular to the interface and X-type for inclined-crossing arrangement. The transverse reinforcement ratio at the interface varied from 0.0045 to 0.0135 for V-type and 0.0064 to 0.0045 for X-type. The mechanism analysis proposed for monolithic concrete interface, derived based on the upper-bound theorem of concrete plasticity, was modified to evaluate the shear friction capacity of concrete interfaces with smooth construction joint. Test results showed that the specimens with X-type reinforcement had lower amount of relative slippage at the interface and higher shear friction capacity than the companion specimens with V-type reinforcement. This observation was independent of the unit weight of concrete. The mean and standard deviation of the ratios between the experimental shear friction strength of smooth construction joints and predictions obtained from the proposed model are 1.07 and 0.14, respectively.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.420-429
• /
• 2002

The amount of $CO_2$-silicate bonded waste foundry sand(WFS) occurred in Korea is over 800,000 ton per year. WFS, as a by-product, is generated through manufacturing process of foundry may affect our environmental contamination, The reason is that WFS has been buried itself not less than 90％ out of total WFS. So, it can give damage on the ground of contamination in soil and underwater. Therefore, it is necessary to establish the method recycling WFS because of being intensified waste management law. In this study, we performed the research with respect to harmful component analysis, the qualities of WFS mortar and concrete mixed with WFS. As the results the specific gravity of WFS is the same as that of natural aggregate while unit weight and percentage of solids of WFS are smaller than those of it. But it is found that WFS can be used by substituting WFS for natural aggregate after control of poor grade of WFS. The flowability of mortar and concrete with WFS is inferior to those of natural aggregate, and the setting time of concrete with WFS is faster than that with only natural aggregate, On the contrary, the bleeding of concrete with WFS is shown good result, and compressive and tensile strength of concrete substituted WFS for 30％ are higher than those with only natural aggregate regardless of elapsed time.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.54 no.1
• /
• pp.124-133
• /
• 2009

Demand for the high quality barley with fibroid material and functional substances has been increasing in recent although the amount of barley consumption decreased drastically during the last two decades. But the limited information on quality of barley makes consumers hard when they purchase barley for their own consumption. Therefore, 51 brand barley, .i.e., 28 naked barley and 23 waxy barley from supermarkets and 10 polished barley from local markets were collected, and their external quality were analyzed to provide basic information on brand barley. Among 51 brand barley, 56% were 1kg package and 25% were 800 g package and there was no significant difference ($1{\pm}3.62\;g$) between printed and actual weighs. The weight of 1,000 grains of naked barley and waxy barley ranged $18.6{\sim}26.7\;g$ and $14.6{\sim}24.7\;g$, respectively. Thousand grain weight of 38% of naked barley ranged $20{\sim}22\;g$, while that of 43% of waxy barley ranged $18{\sim}20\;g$. The ratio of normal grains was 88% and 94% for naked barley and waxy barley, respectively, when separated with 1.7 mm sieve. Although 82% of brand barley products were free from foreign substances, in 18% of brand barley products, sands, pieces of cloth and wood, other kinds of grain and insect larvae were found, Average test weight of brand barleys was $843g{\cdot}L^{-1}$ with range of $805{\sim}917g{\cdot}L^{-1}$. Water content was less than 14% in 7.8% of barley products, while it was $14{\sim}15%$ in 62.7% of them. Average whiteness of brand barley was 31.06, while waxy barley had higher whiteness with 27.28 than naked barley with 34.16. Heated water uptake rate of milled naked barley and milled waxy barley were 215.4% and 231.7%, respectively, while expansion rate of milled naked barley and milled waxy barley were 379.7% and 401.6%, respectively. Barley from local markets were as good as brand barley products in 1,000 grain weight, ratio of normal grains, inclusion of foreign substances, test weight, water content, whiteness, water uptake rate, and expansion rate, but they showed higher ratio of foreign substances included.