• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 1999.11a
• /
• pp.104-108
• /
• 1999

1998년말 현재 우리나라의 시설원예 면적은 48,612ha이고 전체의 90.2%인 43,852ha가 단동비닐온실을 비롯한 관행온실이고, 9.8%인 4,760ha만이 자동화 온실이다. 관행의 단동비닐온실은 태양광에 의존하여 무가온으로 재배하고 있으며, 대부분 2중 하우스로 하거나 내부에 터널을 설치하여 보온덮개를 개폐하는 방식의 보온을 위주로 하여 온실의 온도를 관리한다. (중략)

• Proceedings of the KGS Conference
• /
• 2001.12a
• /
• pp.8-12
• /
• 2001

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2010.04a
• /
• pp.383-384
• /
• 2010

The control surface on a ship is to control the motion of it in forward and backward states. In this paper, the measured results has been compared with each other to predict the backward flow characteristics of the single rudder's 2-dimensional section at $Re=2.0\times10^4$ using 2-frame grey level cross correlation PIV method especially, The separation region appears at 10 to 20 degrees angle of attack in a forward state. The separation point and boundary layer demonstrate in the same angle of attack compared it with the forward states.

• Journal of Bio-Environment Control
• /
• v.6 no.3
• /
• pp.176-182
• /
• 1997

A simulation model for the analysis of the transmissivity of direct and diffuse solar radiation In glasshouse was developed. This model would be applicable to investigate the influences of time of year, orientation and slope of glasshouse, dimensions of the frames used, and latitude of the site on the transmissivity of direct and diffuse solar radiation in single-span or multispan glasshouse. The transmissivity of diffuse solar radiation was 60.4％ for the single-span glass-house. It was independent of both orientation and time of year, During the winter season, the transmissivity of direct solar radiation was 67~69％ for the E-W orientation single-span glasshouse, which was 14~16％ higher than that for the S-N orientation. Oppositely the transmissivity of direct solar radiation for the S-N orientation was higher than that for the E-W orientation. during the autumn season. There was no influence of the latitude In the country on the transmissivity of direct solar radiation.

• Journal of Bio-Environment Control
• /
• v.29 no.4
• /
• pp.428-439
• /
• 2020

This study was carried out to investigate the effect of PO film on the increase of crop yield and energy saving through PO and PE film greenhouse application and comparison test. As a experimental greenhouse, two single span greenhouses (1-1 W) and two double span greenhouses (1-2 W) were used. During winter season, PO film (0.15 mm outer layer, 0.10mm inner layer) was used as a covering material of greenhouse in double layers for double-span (B15) and single-span(B21), and PE film used for double-span (B15), and single-span (B23) as a control. The experimental vegetable was tomato(Solanum lycopersicum L.) cultivated in soil and the cultivar of that was 'Happiness'. That was cultivated from December 3, 2019 to April 30, 2020. The temperature at night inside the greenhouse was maintained at 15℃, and the side and roof windows were opened to maintain 23 ~ 24℃ during the day. As a result, this study showed that the yield in single-span greenhouse(B21) covered with a PO film increased 20% and that in double-span greenhouse (B16) increased by 9% compared to the greenhouse covered with a PE film (B23, B15). Fuel consumption of the single-span greenhouse (B21) with the cover of PO film was reduced by 12.4% and that of double-span greenhouse was done by 11.5% compared to that of the PE film greenhouse (B23, B15) without any difference between them in growing state.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.68 no.3
• /
• pp.106-113
• /
• 2023

We examined the heading responses of rice varieties over two years in Dandong, China to select the varieties that are adaptable to the bordering northwestern plains of North Korea. Dandong had slightly lower mean temperature than Sinuiju, North Korea but slightly higher than Supung, but it had almost the same day-length as the two regions in North Korea. In the two experimental years and two transplanting-date treatments, eight varieties (Jinbuol, Baegilmi, Joun, Jinok, Jopyeong, Jinbu, Sanhomi, and Odae) from South Korea and five varieties (Olbyeo2, Sonbong9, Onpo1, Gilju1, and Pyongdo5) from North Korea reached the heading stage not later than the latest heading dates of Dandong domestic varieties and the safe marginal heading dates of Dandong. We examined the basic vegetative phase (BVP), photoperiod-sensitivity (PS), and thermo-sensitivity (TS) of rice heading in a phytotron study to characterize the heading ecotypes of rice varieties adaptable to Dandong. For the rice varieties grown in Dandong experimental field, number of days to the heading stage was highly positively correlated with PS and, except middle and mid-late maturing three varieties, it was significantly positively correlated with BVP. Two-dimensional distribution plotting revealed that both 35 days or less BVP and 25 days or less PS were the characteristic heading ecotypes of the rice varieties adaptable to Dandong.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.59 no.1
• /
• pp.30-35
• /
• 2017

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.36-38
• /
• 2007

본 논문은 연자성체를 이용한 모터코어 성형 시 성형 방법에 따른 밀도 특성에 대한 연구이다. 밀도는 성형된 연자성체에서 자기적 특성에 가장 큰 영향을 미치는 인지로써 모터 설계 시 큰 영향을 준다. 본 연구에서는 단동식, 복동식 압분 방법에 대한 밀도 분포의 고찰을 실시하였고, 복동식의 평균 밀도가 단동식 보다 향상됨을 알 수 있었다. 또한 성형 방법에 따른 밀도의 분포도를 작성하여 모터 코어 각 부분에서 밀도의 분포 추이를 파악 할 수 있었으며, 향후 이를 이용한 모터 설계의 표준을 제공 할 수 있을 것으로 사료된다.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2006.09a
• /
• pp.71-76
• /
• 2006

Preliminary conceptual design of hulls is developed and a theoretical evaluation study performed for the comparison of the hull concepts. Systematic variation of the side hull location is carried out to find an optimum position of side hulls for a trimaran by CFD computation. In order to compare computed results, the model test of trimaran was carried out. Shallow water effect is considered due to the route which has critical water depth of 20m for the design speed and investigated on the condition of different speeds and water depth by the numerical computations.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.76-83
• /
• 2001

This paper is concerned with the analysis of the forming characteristics of radial-backward extrusion. The single action pressing is analyzed by using the rigid-plastic FEM. The design factors such as die corner radius, gap height, and friction factor are involved in the simulation. The analysis is focused on the influences of the design factors on the maximum punch farce and metal flow into can and flange region. As a result of analysis, the gap height among the design factors is known to have a major effect on the metal flow of radial-backward extrusion for single action pressing compared with other design factors. As is expected, forming load and volume of flange increase as gap height and die corner radius increase, respectively.