• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.66-73
• /
• 2004

This paper presents characteristics of combustion and exhaust gas properties according to variation of the combustion chamber for economy and emissions standards. In order to use combustion and exhaust gas properties data, it is necessary to build some data base, which use cylinder pressure sensor and emission tester. A feasibility and necessity of combustion pressure based cylinder spark timing control has been examined. So, this was obtained the coefficient of variation(COV) and the specific fuel consumption(sfc). Using the results of the test, the effects of the variable combustion chamber can be improved combustion stability and be reduced exhaust emission.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권9호
• /
• pp.911-917
• /
• 2015

본 논문에서는 함정용 디젤연료를 단기통 커먼레일 디젤엔진에 적용하여 연료분사압력 변화에 따른 분사율 특성, 거시적 분무 특성 및 연료분사시기와 연료압력변화에 따른 연소 및 배기가스 배출특성을 분석하는데 초점을 두었다. 분사율 특성은 Bosch법을 적용한 분사율 측정 시험 장치를 이용하여 분석하였고, 거시적 분무 특성은 정적용기 및 초고속 카메라를 이용하여 분석하였다. 또한, 연료분사시기 및 연료압력 변화를 정밀하게 제어할 수 있는 단기통 엔진을 이용하여 연소 및 배기가스 배출특성을 분석하였다. 30MPa과 50MPa의 분사조건에서 초기 분사율은 50MPa의 분사조건에서 크게 나타났으며, 분무 발달(투과) 또한 동일시간대에서 큰 것으로 분석되었다. 연료분사시기가 지각될수록 실린더 내부 최대 압력과 최대 열발생량은 떨어지는 경향으로 나타났으며, 고압분사조건에서 실린더 내부 최대압력과 최대 열발생량은 다소 큰 것으로 분석되었다. 고압분사조건에서 도시평균유효압력은 낮은 것으로 분석되었고, 연료분사시기가 TDC 쪽으로 지각될수록 도시평균유효압력 및 토크는 증가하는 것으로 나타났다. 연료분사시기가 $BTDC20^{\circ}$(30MPa)와 $BTDC15^{\circ}$(50MPa)에서 질소산화물 발생수준이 가장 높았으며, 일산화탄소는 $BTDC30^{\circ}$를 기준으로 지각될수록 저감되었다.

• 대한기계학회논문집B
• /
• 제35권12호
• /
• pp.1359-1365
• /
• 2011

본 연구의 목적은 디젤-에탄올 혼합연료로 운전되는 디젤엔진에서 에탄올 혼합비율이 나노 크기 입자 배출 특성에 미치는 영향을 분석하는 것이다. 엔진의 연소 및 배기 배출물 특성은 배기량 373cc 의 단기통 디젤엔진과 배기 배출물 측정 장치, SMPS 를 이용하여 실험하였다. 그을음(soot) 배출은 착화지연 기간이 길어짐에 따라 증가하였다. 에탄올 혼합비율이 증가함에 따라 나노 입자의 총 개수 및 질량은 대체로 감소하는 경향을 나타냈다. 그러나 에탄올이 30% 혼합되었을 때 그을음(soot) 입자의 응결로 인해 큰 입자의 수 분포가 증가하였으며, 질량 또한 크게 증가하였다.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.65-72
• /
• 2011

In this study, the numbers, sizes of particles from a single cylinder direct injection spark-ignition (DISI) engine fuelled with gasoline and LPG are examined over a wide range of engine operating conditions. Tests are conducted with various engine loads (2~10bar of IMEP) and fuel injection pressures (60, 90, and 120 bar) at the engine speed of 1,500 rpm. Particles are sampled directly from the exhaust pipe using rotating disk thermodiluter. The size distributions are measured using a scanning mobility particle sizer (SMPS) and the particle number concentrations are measured using a condensation particle counter (CPC). The results show that maximum brake torque (MBT) timing for LPG fuel is less sensitive to engine load and its combustion stability is also better than that for gasoline fuel. The total particle number concentration for LPG was lower by a factor of 100 compared to the results of gasoline emission due to the good vaporization characteristic of LPG. Test result presents that LPG for direct injection spark ignition engine help the particle emission level to reduce.

• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.95-102
• /
• 2006

Recently particulate matter(PM) emission regulations are becoming more strict for diesel engines. There is increasing interest for measuring not only concentration but also size of the particles. Laser-induced incandescence (LII) has emerged as a promising technique for measuring particle volume fraction and size. In this study, the Simple Time Resolved-LII method was applied to exhaust of Ethylene diffusion flame and diesel engine exhaust for measuring soot and PM size. The particle size data from LII technique were calibrated using Field Emission Scanning Electron Microscope(FE-SEM) and Transmission Electron Microscope(TEM) photographs. In diesel engine experiments for particle size measurement, results from LII measurement are in a good agreement with those from TEM photograph, and difference between two measurements was less than 16%.

• 한국자동차공학회논문집
• /
• 제24권2호
• /
• pp.152-160
• /
• 2016

The market demand for diesel engine tends to increase in general passenger cars as well as commercial vehicles because of its advantages. However, to meet the vehicle emissions regulation which will be more stringent in the future, it is necessary to plurally apply all after-treatment technologies such as diesel oxidation catalyst (DOC), catalyzed diesel particulate filter (CDPF), lean NOx trap (LNT) and selective catalytic reduction (SCR), and so on. Accordingly, the exhaust after-treatment system for diesel vehicle requires the technology of minimizing the numbers of catalysts by integrating every individual catalysts. The purposes of this study is to develop hybrid exhaust after-treatment device system which simultaneously uses LNT/DPF and SCR/DPF catalyst concurrently reducing NOx and particulate matter (PM). As the results, the hybrid system with $NH_3$ generated at LNT/DPF working as a reducing agent of SCR/DPF catalyst, improving NOx conversion rate, was found to be more excellent in de-NOx performance than that in LNT/DPF alone system.

• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.20-25
• /
• 2011

The purpose of this work is an experimental investigation of combustion and emission characteristics in DI diesel engine applied high EGR rate as a method of low-temperature combustion. In order to analyze the effect of EGR rate variation, a single-cylinder DI diesel engine was operated under various EGR rate conditions. In addition, injection timing was variously controlled to investigate the effect of injection timing in DI diesel engine using the cooled-EGR system. The NOx emissions were decreased in accordance with the increase of EGR rate. On the contrary, soot emissions were generally increased under applied EGR conditions. However, soot emissions were decreased in a few injection timings under high EGR rate conditions. The EGR results show that the ignition delay were increased by decreased oxygen concentrations in combustion chamber under the high EGR rate.

• 한국자동차공학회논문집
• /
• 제8권5호
• /
• pp.96-104
• /
• 2000

It is well known that combustion stability under idle and part-load conditions directly affect fuel economy and exhaust emission. In practice, there have been a lot of studies so that a significant improvement in combustion stability has been achieved in this research field. However, applying published results to the development process of mass production engine, there are still many problems which are solved previously. In this study, initial flame behavior and flame propagation characteristic were investigated statistically in order to optimize combustion chamber shapes in the development stage of mass production S.I. engine. To the purpose, the authors applied the flame image capturing system to single cylinder optical engine. The captured flame images were effectively analyzed by using the image processing program which was developed by the authors and adopted new threshold algorithm instead of conventional histogram analysis. In addition, the cylinder pressure was also measured simultaneously to compare evaluated flame results with cylinder pressure data in terms of the combustion characteristics, combustion stability, and cycle-to-cycle combustion variability.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.13-20
• /
• 2005

The most typical fuel control devices of motorcycle engines have carburetors, they are simple in structure and reliable in work. Most of the motorcycle engines have used carburetors in the fuel system, but the fuel economy and the emissions of those engines are bad when we compared with automobile engines. According to stricter emission regulations and higher requirements for fuel economy, the application of the carburetor on the motorcycle engines would be limited. In this paper, we studied about the ECU of motorcycle engine controled by indirect method. A new engine system was designed and experiments were carried out. The experimental results for both carburetor type and ECU type were compared. Maximum torque of $1.053kg{\cdot}m$ at 6500rpm was measured. The engine torque controled using ECU was increased by $10\%$ compared with the carburetor type.

• 한국연소학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2017

This paper presents an experimental study on the effect of double injection strategies on combustion characteristics in a single-cylinder diesel engine. These studies are applied to the double injection strategies, such as $2^{nd}$ injection timing variations with fixed injection interval (8 degree) and variations of injection pressures with fixed injection timing and intervals. The injection quantity was 7 + 7 mg for double injections, and 14 mg for single injection. When the injection pressure was increased, the ignition delay was shortened, and the ISFC (indicated specific fuel consumption) was increased due to the fast termination of combustion by the shortened energizing duration. In addition, the retardation of injection timings toward TDC (top dead center) caused the reduction of ignition delay and the decrease of ISFC with the decrease of FMEP (friction mean effective pressure).