• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.12B
• /
• pp.2292-2297
• /
• 1999

Some observed weather spectra show that nearly 25% of weather spectra are seriously skewed and can not be considered to be symmetric. However, the conventional pulse pair method was derived and has been evaluated under the assumption that the weather spectrum is symmetric and narrow. This means that the conventional pulse pair method may need reevaluation. Therefore, this paper analyzed the bias errors of pulse pair estimates in the skewed spectra. The bias errors of pulse pair mean estimates are more serious comparing with the pulse pair width estimates. In this paper, the poly-pulse pair method is suggested to reduce these bias errors of mean estimates. It was shown that the mean bias errors can be reduced remarkably using the newly suggested poly-pulse pair method.

• Journal of the Korea Computer Industry Society
• /
• v.2 no.7
• /
• pp.975-982
• /
• 2001

In this study, a solid-state laser system adopting a new real time multi-discharge (RTMD) method in which three flashlamps are turned on consecutively was designed and fabricated to examine the pulse width and the pulse shape of the laser beams depending upon the changes in the lamp rum-on time. That is, this study shows a technology that makes it possible to make various pulse shapes by turning on three flashlamps consecutively on a real-time basis with the aid of a PIC one-chip microprocessor. With this technique, the lamp turn-on delay time can be varied more diversely from 0 to 10 ms and the real-time control is possible with an external keyboard, enabling various pulse shapes. In addition, longer pulses can be more widely used for industrial processing and lots of medical purposes

• Korean Journal of Optics and Photonics
• /
• v.11 no.5
• /
• pp.330-334
• /
• 2000

A new pha~e lock loop (PLL) IS proposed and demonstrated fat clock recovery from 40 Gblt/s time-dIvision-multiplexed (TDM) optical pulse tri.lin, The proposed clock lecovery scheme lmproves the Jitter effecl cOlmng from the clock. pulse laser of harmonically-mode locked flber laser The cross-corrdation frequency component between the optical Signa] and an optical clock pulse tram is deteCled as a fonr-wave-mixing (FWM) SIgnal generated in SOA. The lock-in freqnency range of the clod. recovery IS found to be within 10 KHz. 0 KHz.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.4 no.2
• /
• pp.73-81
• /
• 1993

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.133-136
• /
• 2003

UWB(Ultra-Wide Band) system is transmitted using Gaussian monocycle pulse of very short pulse duration less than 1 nsec. Therefore, transmission signal has ultra-wide band spectrum to GHz band of very low power and not interfere with the existing communication system. A collision of multipath waves in UWB system with tarrier frequency very different with general wireless communication system. In this paper, the BER(Bit Error Rate) performance of UWB system applying Binary Phase Shift Keying, Quadrature Phase Shift Keying, 16-Quadrature Amplitude Modulation method under multipath channel using computer simulation is compared and analyzed.

• Korean Journal of Optics and Photonics
• /
• v.15 no.5
• /
• pp.449-454
• /
• 2004

The optical limiter is an optical component which reduces laser beam intensity for the protection of eyes and light sensors. Carbon nanotube is now known as a highly efficient optical limiting material. Optical limiting effect of the multi-walled carbon nanotube suspensions, in several kinds of solvents such as distilled water, chloroform, ethanol and ethylene glycol, were measured in the range from room temperature to near to the boiling points of the solvents. The pulsed Nd:YAG laser whose wavelength is 1064 nm and pulse duration is 6 ns was used as a light source. The experimental result shows that the limiting efficiency was reduced as the temperature increased, and the suspension which has lower boiling point, viscosity and surface tension has highest efficiency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1036-1043
• /
• 2016

In this paper, an analysis about the elevation angle accuracy degradation of an APAR(Airport Precision Approach Radar) due to the multi-path effect using a phased array antenna was performed. An APAR installed around a runway of airport will be continuously affected in a runway surface of the fixed environment. In this paper, an analysis about the elevation angle accuracy degradation of APAR due to the multi-path effect of runway surface was conducted through a calculation of monopluse slope and sum/difference beam pattern analysis of array antenna. Also, a difference pattern for monopulse to minimize this degradation was optimized in an appropriate configuration to improve a elevation angle accuracy. Finally, a degree of improvement of elevation angle accuracy was confirmed by calculating a monopulse slope including the ground reflection after applying optimized difference patterns of array antenna.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.5
• /
• pp.1117-1122
• /
• 2005

This paper is studied the high-repetition rate optical-pulse stream generation using optical loop mirror coupler. With the recent development of the ultrahigh-speed optical time division multiplexed system, hish-repetition rate optical-pulse stream generation is necessary. This is different from conventional approaches, which use fiber or integrated waveguide delay line circuits. The high-repetition-rate optical-pulse multiplication phenomenon occurs when the optical pulse's spectral width is greater than the transfer bandwidth of the coupler used. From the analysis, the output repetition rate can be controlled by using fiber couplers with different equivalent transfer bandwidths. The pulse separation spacing is controlled by number of cascaded coupler in optical loop mirror coupler scheme.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.12C
• /
• pp.1201-1207
• /
• 2005

When the isolation between transmitter and receiver in Electronic Warfare equipment is not sufficient, the radiated noise jamming signal from the transmitter feeds back into the receiver and interferes with receiving radar pulse signal. Therefore pulse jamming and noise jamming can't be performed together in the same frequency bands. In this paper, we present a time-sharing TX/RX control technique of the switch matrix which inhibits the transmission of noise jamming signal by using the predicted gate of pulse train and also makes the corresponding channel filter operate to receive the radar pulse signal during the predicted gate pulse. This technique was implemented by EPLD and confirmed by experiment. The proposed technique enables the pulse jamming and the noise jamming to be simultaneously executed in multiple jamming environments.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.1105-1111
• /
• 2011

The objective of this study is to investigate the influence of surface roughness on the morphology of aluminum 6061-T6 alloy after irradiation with a Nd:YAG pulsed laser. The test specimen was prepared by a polishing process using a diamond paste ($1{\mu}m$) and emery polishing papers (#100, #220, #600, #2400) to obtain different initial surface roughness. After irradiation with ten pulsed-laser shots, the surface morphology was examined by using scanning electron microscopy (SEM), optical microscopy (OM), and atomic force microscopy (AFM). The diameter of the melted zone increased with the surface roughness because the multiple reflections and absorption of the laser beam occurred on the surface because of the surface roughness, so that the absorptance of the laser beam changed. This result was verified using the relative absorptance calculated from the diameter of the melted zone with the surface roughness and the diameter increased with the average surface roughness.