• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.197-198
• /
• 2010

The purpose of this study is to compare chloride attack resistibility of light weight aggregate concrete to chloride attack resistibility of normal concrete and confirm the utility. As a result, light weight aggregate concrete's chloride attack resistibility is lower than normal concrete's chloride attack resistibility.

• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.331-338
• /
• 2013

Under the paradigm of sustainable green growth at the national level, various researches and applications for energy saving in the construction field has been attempted. As a part of energy saving efforts, lightweight concrete was investigated for thermal insulation concrete with phase change material (PCM) which has high heat storage capacity. As a part of energy saving efforts, thermal insulation concrete was investigated and evaluated with lightweight aggregate impregnated by PCM which has high heat storage capacity. As a result, it is found that concrete with lightweight aggregate impregnated by PCM is effective to prevent its quality deterioration by reducing water absorption rate of lightweight aggregate. In addition, it has shown that concretes using lightweight aggregate and impregnated lightweight aggregate improve heat insulation property 33% and 40~43% compared with using normal aggregate, respectively. It is that the lightweight aggregate concrete with impregnated lightweight aggregate has 12~14% lower thermal conductivity than unimpregnated.

• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.176-181
• /
• 2004

EAF (Electric Arc Furnace) dust is classified as special wastes containing heavy metal contaminants may cause to damage an environment such as underground water contamination if they were not treated properly. For reutilizing the EAF dust, the porous body was made from EAF dust/clay composition system, and analyzed pore characteristics. It was found that a light-aggregate body was made up two different microstructures. One was non-black and dense microstructure which located near surface, and the other was black and porous microstructure (black coring) which located inner part. For systematizing the relationship of the black-coring area and the bloating degree, we defined the Ic(core index) and Is(shell index). It was found that the optimal bloating conditions of artificial light-weight aggregate were more than 0.5 of Ic and 0.4 of Is.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.537-544
• /
• 2020

The interfacial transition zone(ITZ) which is the boundary layer between cement composites and aggregates is considered to be the region of gradual transition, heterogeneous, and the weakest part of concrete. For the development of lightweight high strength concrete, it is essential to evaluate the mechanical properties of ITZ between high strength concrete with low water-binder ratio and lightweight aggregates. However, the mechanical properties of ITZ are not well established due to its high porosity and complex structure. Furthermore, the properties of ITZ in concrete using lightweight aggregates are dominated by more various variations (e.g. water-binder ratio, water absorption capacity of aggregate, curing conditions) than normal-weight aggregate concrete. This study aims to elucidate the mechanical properties of ITZ in lightweight high-strength cement composites according to the types of aggregates and the aggregate sizes. Nanoindentation analysis was used to evaluate the elastic modulus of ITZ between high strength cement composites with the water-binder ratio of 0.2 and normal sand, lightweight aggregate with different aggregate siz es of 2mm and 5mm in this study.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.35-38
• /
• 2003

The purpose of this study is to investigate the manufacture of light weight concrete panel using the artificial light-weight aggregate as a part of the substitution of foamed styrene and polyurethane because of narrow allocable temperature Bone in use. The experimental parameter of this study is 40, 60 and 8$0^{\circ}C$ of curing temperature at 100% relative humidity and the type of admixture such as cement, 6mm glass fiber and St/BA emulsion. Testing item is compressive and flexural strength and strength of specimen cured at standard condition is compared to that of specimen cured at 40, 60 and 8$0^{\circ}C$ of curing temperature at 100% relative humidity. As a result or this, it was revealed that the maximum or strength is developed in 6$0^{\circ}C$ or cure temperature at 100% relative humidity in case of the most of the specimen. Specimens modified by St/BA emulsion show the highest development of strength dependent on the curing tmeperature. So, it seems to be effective that evaporation curing method shoud be considered to curing the specimen as the panel core.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.6
• /
• pp.113-123
• /
• 2012

The technology developed for the decrease of applying loads and self-weight of a structure is to improve conventional Foam Cement Banking Method (FCB) by applying mixed slurry of bottom ash, cement and foams. Since the foam-mixed concrete, which is a major material of the Bottom ash-mixed Light weight concrete Banking method (BLB) developed, contains mineral admixture such as cement, the behavior shows time-dependent deformation and deterioration of durability due to environmental exposure. Thus, this study is subject to figure out the characteristics of long-termed behavior and durability of the developed method by carrying out experiments for schemed parameters, which are considered to be factors affecting mainly on concrete's characteristics from mechanical analysis. As results of tests, it was found that the developed concrete offers higher resistance than conventional foamed concrete in terms of long-termed behaviors associated with drying shrinkage and creep, and durability problems of freeze-thaw and carbonation processes, especially with addition of bottom ash.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4A
• /
• pp.373-384
• /
• 2009

For the first step on the quantitative evaluation of shrinkage reduction and differential shrinkage analysis of lightweight aggregate concrete, this study sets the moisture transport model of concrete by pre-absorbed water of porous lightweight aggregates and measured effective moisture diffusion coefficient, moisture capacity, degree of humidity supply and degree of humidity consumption by water binder ratio and aggregate type. The effective moisture diffusion coefficient in steady state caused by humidity difference between inside and outside of concrete had low value as low water-binder ratio. And in case of same water-binder ratio, effective moisture diffusion of mixtures used normal aggregates were lower than those used lightweight aggregates. To determine moisture store capability of concrete - moisture capacity, moisture contents were measured in 9 humidity conditions. As a result moisture contents of mixtures used lightweight aggregates was higher than mixtures used normal aggregates in all humidity conditions. This study measured lightweight aggregates' degree of humidity supply that applicable to normal atmospheric environment (above RH 50%) and made it quantitatively. Also amount of moisture release was set as a exponential function that represents a clear trend proportion to time and inverse proportion to humidity of the surroundings. As the result of measurement about degree of moisture consumption inside concrete following the internal consumption caused by cement hydration self-drying, it was showed that rapid decrease of humidity, around 10%, at early ages (7~10 days) when water-binder ratio is 0.3 and slow decrease around 5% and 1% when water-binder ratio is 0.4 and 0.5.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.6
• /
• pp.258-263
• /
• 2008

The fine aggregates of below 2 mm size was fabricated using by the vertical furnace in which the aggregates could be sintered at floating state and its physical properties were analyzed. The liquid formed at the surface of specimens sintered at $1200{\sim}l300^{\circ}C$ induced a gas in core to expand so the denser shell and porous core could be produced. The C series specimen fabricated by crushing an extruded body had an irregular shape and sharp edges but those became spheroidized by bloating due to gas expansion inside. The fine aggregates fabricated in this study was as light as floating in the water and had an apparent density of $0.68{\sim}1.08$. The absorption rate was proportioned to a porosity showing that the pores in core was not closed completely. The properties of fine aggregates fabricated in vertical furnace were similar with those of in an electric muffle furnace but the sticking-together phenomenon by surface fusion was not occurred in the vertical furnace. The aggregates fabricated in this study had a little lower impact resistance than that of natural aggregate but satisfied the unit volume weight standard specified in KS.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.625-632
• /
• 2021

In this paper, the applicability of bottom ash to insulation concrete was investigated to increase the utilization of bottom ash. Bottom ash was used as the aggregates in porous concrete and extensive experiments were conducted to investigate the characteristics of porous concrete using two types of bottom ash aggregates. The water-binder ratios of 0.25 and 0.35 were chosen and concrete specimens was produced with the compaction of 0.5, 1.5, and 3.0MPa to analyze the material properties at different compaction conditions. After concrete specimens were cured for 28 days at water tanks, unit weight, total void ratio, and thermal conductivity were measured. Based on the measured experimental results, the relationships between the unit weight, total void ratio, and thermal conductivity of porous concrete containing bottom ash was presented.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.1
• /
• pp.75-82
• /
• 2016

As spreading of train concrete ballast leads to the increase resounding friction noise, an porous sound absorbing block is applied in urban train tunnel as a counterparts against the friction noise. Three steps of major variables tests for an optimal mix design of the block are conducted to pursue the light weight of the block. Pilot property tests of the block for the cases of the fly-ash only as lightweight aggregates are carried satisfying KRT(Korean Rail Transit) and new KRS(Korean Railway Standards). Based on the results of pilot tests, required structural strength and admixture effects are evaluated. Additionally, typical lightweight aggregates are replaced so that lightweight and strength are improved for serviceability of poor working conditions and proper maintenance in urban train tunnel.