• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.335-340
• /
• 1992

유압 시스템(System)은 원동기의 기계적 에너지를 유압펌프가 작동유를 압력 에너지의 형태로변환 시켜 이것을 유합 실린더(Cylinder)등의 엑츄에이터(Actuator)가 다시 기계적 에너지로 변환시켜 부하 를 구동하게한다. 상용차(NT-1, KH 등)용 파워스티어링(Power Steering)에 장착되는 Vane Type Oil Pump (이하 VOP)가 바로 이와같은 역할을 담당하고 있다. 본 연구에서는 VOP의 성능과 관련되어지는 주요 제원(Parameter)인 미끄럼부에서의 틈새, 작동유점도, 압력변화, 회전수 등을 다양하게 변화시키는 모의실험(Simulation)을 통하여각각의 조건하에서얻어지는 누설 유량과 체적효율을 수치적 으로 예측하고 이것을 주요제원을 고려하여 해석해서 정량적인 값을 얻는 것을 목적으로한다.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.72-80
• /
• 1997

One of the concerns in micro fluidic valve designs is that of reverse direction leakage. This paper designs and fabricates a new fluidic valve to achieve zero leakage. The design uses flapper and nozzle elements. In the forward direction the working fluid pushes the flapper upward to allow flow. In the reverse direction, the flapper pushes against the orifice seat, and thus, no flow can be generated, unless the flapper or nozzle element breaks. The nozzle element fabrication involves fabricating an orifice by wet etching of (100) wafer, The flapper element fabrication involves $20{\mu}m$ deep patterning of the negative image of the flapper, followed by wet etching from backside. Flow experiments were conducted with DI water as the working fluid, and the results are compared to analytical predictions. The results show that the developed flapper-nozzle valve achieves a true diodic flow characteristic.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.143-148
• /
• 2003

This study was experimentally performed in order to estimate the errors due to the leakage of transmitter gaugelines in the orifice flow meter for natural gas. It would be a serious problem in safety if a large quantity of leak was occurred at the tubes or fittings like valve. But in most cases the safety problems might be rarely happened because the gas leak detectors could be operated in advance and the various kinds of inspection would be also fulfilled periodically. If the leakage was occurred continuously with an undetectable amount at the gaugelines for measuring the pressure or the differential pressure(DP), the amount of leakage might be an error or an unaccounted flow(UAE). In addition if the measuring value of pressure or DP were affected by the leakage, it might also be a measurement error. The experiments were performed to estimate the amount of leakage and to check the DP changes if it exited. First, through the measurement of the air pressure changes in the airtight container connected to a transmitter with gaugelines as the time passed, the amount of leakage causing from the fittings of gaugelines was roughly estimated. As changing the leak position of the gaugeline, the leak was intentionally made to break out. The variance of DP was checked as controlling the extent of leakage and compared to no leak conditions. Consequently, under the normal maintenance conditions, the result represented that the amount of leakage causing from the gaugelines was insignificant and also the DP changes on leakage conditions were too small to cause the errors of measurements.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1383-1388
• /
• 2004

The flow characteristics in the blade passage of a low speed axial flow fan have been investigated by experimental analysis using a rotating hot-wire sensor for design and off-design operating conditions. The results show that the tip leakage vortex is moved upstream when flow rate is decreased, thus disturbing the formation of wake flow near the rotor tip. The tip leakage vortex interfaces with blade pressure surface, and results in high velocity fluctuation near the pressure surface. From the relative velocity distributions near the rotor tip, large axial velocity decay is observed at near stall condition, which results in large blockage compared to that at the design condition. Througout the flow measurements using a quasi-orthogonal measuring points to the tip leakage vortex, it is noted that the radial position of the tip leakage vortex is distributed between 94 and 96 percent span for all flow conditions. High spectrum density due to the large fluctuation of the tip leakage vortex is observed near the blade suction surface below the frequency of 1000 Hz at near stall condition.

• Journal of Energy Engineering
• /
• v.21 no.4
• /
• pp.398-401
• /
• 2012

In this Study, efficiencies of the scroll expander under development for organic Rankine cycle using engine waste heat of vehicle have been analyzed and compared with the commercial scroll expander. While operating organic Rankine cycle for analysing expander efficiencies, power of expander, inlet temperature of expander, inlet pressure of expander and the flow rate of the working fluid(refrigerant R134a) have been measured. Overall efficiency of the expander has been shown the very low level compared with the overall efficiency of the commercial expander. Especially, because the low volumetric efficiency has much effect on overall efficiency, the working fluid leakage trouble of expander has to be solved surely for improvement of the expander overall efficiency.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.2
• /
• pp.181-188
• /
• 2004

The frequency characteristics in an axial flow fan operating at a design and three off-design operating conditions have been investigated by measuring the velocity fluctuation of a tip leakage vortex and a wake flow. Two hot-wire probe sensors rotating with the fan rotor. a fixed and a moving ones, were introduced to obtain a cross-correlation coefficient between two sensors as well as the fluctuating velocity. The results show that the spectral peaks due to the fluctuating velocity near the rotor tip are mainly observed in the reverse flow region of higher flow rates than those in the peak pressure operating condition. However, no peak frequency presents near the rotor tip for near stall condition. Detailed wake flow just downstream of the rotor blade was also measured by the rotating hot-wire sensor. The peak frequency of a high velocity fluctuation due to Karman vortex shedding in the wake region is mainly observed at the higher flow rate condition than that in the design point.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.105-105
• /
• 1999

차세대 기억소자에서는 집접도의 증가, 고속화, 그리고 미세화에 따라 배선간으 최소선폭이 작아지고, 새로운 다층 배선기술이 요구되는 가운데 층간절연막의 재료와 형성기술은 소자의 특성을 향상시켜주는 중요한 요소로서 열적안정성, 저유전율, 평탄화특성 등에 핵심을 두고 연구되고 있다. 본 연구에서는 5인치 p-Si(100) 위에 FTES와 O2를 precursor로 하고 carrier gas를 Ar gas하여 ICP CVD 방법으로 저유전율의 Fluorocarbonated-SiO2 박막을 형성하였다. 0.1-1kW, 13.56MHz인 rf power를 사용하였으며, 증착은 RT에서 5~10분으로 하였다. 형성된 박막은 FTIR(fourier transform infrared), XPS(x-ray photoelectron spectroscopy), 그리고 ellipsopsometer 등을 이용하여 결합모드와 F농도, 균일도 등을 측정하고, I-V와 C-V 측정장치, 그리고 SERM(scanning electrion microscopy) 등을 이용하여 유전상수, 누설전류, dielectric breakdown voltage, 그리고 박막의 stepcoverage를 측정하였다. 제작된 박막의 신뢰성은 열처리에 따른 전기적 특성으로부터 조사하였다. 형성된 fluorocarbonated 박막 결합모드는 Si-F, Si-O, O-C, C-C와 C-F였고 O2:FTES:Ar 유량을 1sccm:10sccm:6sccm으로 하여 증착한 시료에서 유전율은 2.8이었으며, 누설전류밀도는 8$\times$10-9A/cm2, Breakdown voltage는 10MV/cm 이상, 그리고 stepcoverage는 91%로 측정되었다.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.4 no.3
• /
• pp.1-6
• /
• 2007

The leakage generated from the clearance between the cylinder bore and the piston is one of the most serious problems in the hydraulic piston pump, and it even results in terrible decrease of the volume efficiency at a great velocity and high pressure. In this paper, the lubrication characteristic of the hydrostatic slipper bearing equipped in the hydraulic piston pump has been worked out by experimentation with three model bearings of different shape. Preparatory to this, not only the three models of piston-slipper were designed, but the corresponding experimental apparatus were also manufactured. As a result, it was verified that, according to the supply pressure, the hydrostatic bearing part of the slipper is severely affected by the pocket pressure, land pressure, oil film thickness, and leakage flow.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.3 s.234
• /
• pp.322-329
• /
• 2005

The flow characteristics in the blade passage and in the wake region of a low speed axial flow fan have been investigated by experimental analysis using a rotating hot-wire sensor for design and off-design operating conditions. The results show that the tip leakage vortex is moved upstream when flow rate is decreased, thus disturbing the formation of wake flow near the rotor tip. The tip leakage vortex interfaces with blade pressure surface, and results in high velocity fluctuation near the pressure surface. From axial velocity distributions downstream of the fan rotor, large axial velocity decay near the rotor tip is observed at near stall condition, which results in large blockage compared to that at the design condition. Although the wake flow downstream of the rotor blade is clearly measured at all operating conditions, the trough of the high velocity fluctuation due to Karmann vortex street in the wake flow is mainly observed at a higher flow condition than the design flow rate.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.1 no.2
• /
• pp.8-14
• /
• 2004

Abstract: In the oil hydraulic piston pumps the clearance between the valve plate and cylinder block plays an important role for volumetric and overall efficiency. Thus, adequate lubricational fluid film is needed for the interface. In this study, fluid film thickness is measured by a gap sensor and a slip ring under operational conditions to observe the behavior of the lubrication mechanism in detail. To investigate the effect according to the valve plate types in view of the fluid film, three different types were designed. Leakage flow rate and shaft torque were also measured to clarify the effect according to the valve plate types. A broad range of experiments were conducted to provide reasonable data on the effect of fluid film. In this experiments two main parameters were found, of which the one is the discharge pressure and the other is valve plate geometry. As a result, we found that the spherical valve plate could get more stable fluid film thickness, maintain good efficiency for high pressure range than the other types.