• Nuclear Engineering and Technology
• /
• v.4 no.2
• /
• pp.116-131
• /
• 1972

A fast neutron time-of-flight spectrometer has been constructed with suitable choice of target thickness and proton bombarding energy in Li$^{7}$ (p, n) Be$^{7}$ nuclear reaction for a continuous keV spectrum of neutrons at 0 degree in 1-nsec pulse from a Van do Graaff and a time-pick-up fast neutron detector assembled with a 5 mm-thick 92% enriched B$^{10}$ slab and four heavily shielded 4＂$\times$3＂ NaI scintillation detectors. Energy resolution of this spectrometer is better than 0.3% at 50 keV and the signal-to-background ratio is also improved. Total cross section measurements of several separated single isotopes have been carried out with this spectrometer and analyzed by Rmaxtrix multi-level computer code. The spin values and resonance parameters of each individual resonances are given.

• Analytical Science and Technology
• /
• v.26 no.1
• /
• pp.34-41
• /
• 2013

Split-flow thin cell (SPLITT) fractionation (SF) is a rapid separation technique capable of separating colloidal particles or macromolecules into two or more fractions. SF allows fractionations in a preparative scale as sample is fed continuously. Generally SF uses a thin ribbon-like channel equipped with two flow stream splitters at the inlet and outlet of the channel. Thus there exist two flow inlets and two flow outlets at the top and bottom of the inlet and outlet of the channel, respectively. There are two operating modes in SF, conventional mode and full-feed mode (FFD). Although the resolution in the FFD mode is lower than that in the conventional mode, FFD mode has some merits. The design of the channel and operation are simpler in the FFD mode, as it does not require the feeding of the solvent. Thus there is no flow stream splitter at the channel inlet, and only one pump is needed, unlike the conventional mode, where two pumps are required for the feedings of the sample and the solvent separately. Also the sample is not diluted in the FFD mode as there is no solvent feeding, which is important for fractionation samples with low colloidal concentrations such as environmental samples. For some of environmental samples, pre-concentration is often required. In this study, a new large-scale splitter-less FFD-SF channel was implemented, where there is no splitter at the outlet as well as at the inlet of the channel. It was possible to build the channel in a much larger dimension than conventional ones, allowing much higher sample throughput (TP). The new channel was tested and optimized with polyurethane (PU) latex beads, and then applied to large-scale separation of Polyacrylate (PA).

• Food Industry
• /
• s.94
• /
• pp.37-40
• /
• 1988

1) 본 연구에서 시료로 선정한 충남 서산산 건강(dry ginger)은 수분이 $9.4\%$, 회분이 $8.7\%$ 그리고 alcohol에 의한 추출량이 약 $9\%$이다. 이는 선진국에 채택사용하고 있는 건강의 규격기준에 의하면 양호하다. 2) Non- flavor물질의 추출을 최소화하고 특히 증류과정에서 유효성분 손실을 최소화 할 수 있고, 엑기스내의 용매 잔류량이 인체에 유해하지 않고 추출효율을 높일 수 있는 용매는 ethyl alcohol이다. 3) 널리 사용하고 있는 관류추출(percolation)의 성능을 분석하고 이의 개선방안을제시하였다. - 추출효율을 높이기 위하여 건강(dry ginger)의 입자를 작게하면 압력강하가 증대되어순환되는 용액의 유속을 제어하기가 힘들다. - 입자가 작을 시에는 유체의 흐름이chan-nelling현상을 나타낸다. - 위와 같은 조건에서는 물질 전달속도가 느리므로 추출효율을 증대시킬 수가 없다. - 따라서 percolation추출에 사용되는 건강의 입자크기는 30mesh크기 이상이어야 운전조작이 용이하나 추출효율이 낮으므로, 추출시간 6시간에 회수된 생강엑기스양은 약 $2.5\%$이다. 4) percolation추출의 단점을 보완하기 위하여 기계적교반 추출을 선택하여 다음과 같은 개선점을 찾았다. - 교반형 추출에서는 고 - 액분리시 cake 저항에서 문제가 야기되지 않는 범위까지 건강의 입자를 작게할 수 있으므로 추출효율을 크게 향상시킬 수 있었다. 즉, 작게 분쇄된 건강(30mesh통과$90\%$)을 대상으로 추출시간 3시간에 $7\%$의 회수율로 증대시켰다. 최적 운전조건은 다음과 같다. 건강시료:1kg 시료크기:-30mesh$90\%$ 용매:ethyl alcohol 3$\iota$ 교반속도:900r.p.m 추출온도:상온($15\~25^{\circ}C$) 추출시간:3시간 일차 추출조건과 동일하게 하여 얻어진 엑기스의 수율이 $2\~2.5\%$이므로 총엑기스의 수율은 건강(dry ginger)무게기준으로 $8.5\~9.5\%$이었다. 5) 교반추출의 효율이 개선되었다 하더라도 추출물의 분리가 용이하여야만 공정의 이용이 가능하다. 그러므로 교반추출후 고 - 액분리를 위하여 정압여과 장치를 이용하여 여과시 cake의 평균 비저항을 얻었으며, 이의 값은 $4.31\times10^8cm\;/\;gr$으로서 여과에는 어려움이 없다는 것을 의미한다. 따라서 추출속도와 효율이 상대적으로 우수한 교반형 추출기의 가능성을 예시할 수 있음을 알 수 있었다. 6) 추출물을 농축과정에서 휘발성 oil의 손실을 최대로 줄이기 위해서는 단순증류를 하지 말고 분별증류를 수행하여야 하며, gingerol과 같은 중요성분의 열분해 반응을 억제하기 위해서는 열전달 효율을 증대시켜 증류조작을 원활히 수행하여야 하므로, still내의 농축물을 계속 교반시켜야 하며 감압상태에서 증류온도는 $40\~50^{\circ}C$로 유지시키는 것이 가장 바람직하다. 7) Ethyl alcohol로 추출된 엑기스내의 수분이나 회분함량은 외국산 제품에 비하여 약간 낮고, 반면에 조지방 및 조단백 성분의 함량은 약간 높게 나타나고 있어 대체적으로 본 연구에서 얻어진 엑기스내의 비풍미성분(non- fla-vour component) 함량은 외국산에 비하여 많은 차이가 없다. 8) 수입 외국산에 비하여 국산엑기스(본 연구에서 ethyl alcohol로 추출)내의 무기성분등의 함량은 비교적 낮은 편이다. 9) 건강에서부터 oleoresin을 얻어 paradol을 제거시킨 후 순수한 gingerol을 분리하여 IR과 NMR로 확인한 결과, 국산건강의 엑기스에는 주로 6-gingerol이고 약간의 10-gingerol이 함유된 것으로 나타났다. 10) 순수하게 분리된 gingerol을 열분석(TGA와 DTG)한 결과 약 $75^{\circ}C$에서 gingerol의 열분해 반응이 일어남을 알수 있었다. 11) 건강 분말시료와 엑기스내의 미생물 검사 결과 건강분말에서는 세균수가 많이 존재하는 것으로 나타났으나, 이는 ethyl alcohol로 추출하는 공정 중 대부분의 균들이 사멸된 것으로 나타났다. 12) 관능적 측면에선, 본 연구에서 제조한 엑기스와 수입엑기스를 비교한 결과 생강 특유의 맛은 비슷했으나, 수입엑기스에서는 쓴맛과 톱밥냄새를 느낀다는 결과를 나타내었으며 전체적인 종합적 풍미는 국산 건강엑기스가 좋은 것으로 나타났다.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.4 no.4
• /
• pp.3-11
• /
• 2001

To know the seawater infiltration into tidal flat sediment in coastal area is very important, because it is significantly correlated with the infiltration and transportation of pollutants in soil, the supply of dissolved oxygen, nutrients and organic matter to benthic organisms for survival of benthic organisms and the seawater purification. So, we set up purpose to clarify the infiltration behavior of seawater by wave action in tidal flat, to clear the effects of slope of tidal flat and breaking wave height on seawater infiltration and to quantify the infiltration volume of seawater. For purpose, the seawater infiltration was studied with visualization method by using coloring tracer and transparent glass beads replaced as natural sediment in model tidal flat. Specific conclusions derived from this study are as follows. The semi-circular type infiltration of seawater by wave action into saturated sediment was a new infiltration behavior that was not considered in previous studies. The infiltration rate of seawater was increased with increasing of breaking wave height and slope of tidal flat. However, the effects of the slope was bigger than that of breaking wave height on seawater infiltration into tidal flat sediments. It was possible to calculate the infiltration volume of seawater by wave action in natural tidal flat sediment and in fields. Therefore, we can point out that wave action play an important role in the supply of dissolved oxygen, nutrients and organic matter to benthic organisms, transportation or diffusion of pollutants and seawater purification. So, we hope to be studied the supply of food to benthic organism, pollutant transport and seawater purification on the base of these results.

• Journal of Radiation Protection and Research
• /
• v.22 no.4
• /
• pp.309-317
• /
• 1997

The measured radioactivity of gamma-emitting radionuclides in each radioactive waste drum using the non-destructive waste assay method is underestimated than real radioactivity in radioactive waste drum because the gamma-rays are attenuated within the medium. Therefore, the measured radioactivity should be corrected for the attenuation of gamma-rays. For the correction of the attenuation of gamma-rays, the attenuation correction method should be applied differently by considering the distribution and density of medium in radioactive wastes drum generated from nuclear power plants. In this study, the model drums were fabricated for simulating five types of radioactive waste drums generated from nuclear power plant and the optimum methods of the attenuation correction were experimentally determined to analyze the activity of radionuclides in the waste drum accurately using the segmented gamma scanning system. With the determination of the attenuation correction methods from the experimental results the transmission method and the average density method for the miscellaneous waste drum, the transmission method and the differential peak absorption method for the shielded miscellaneous waste drum were used to measure the density of medium in waste drums. Also, the average density method and the differential peak absorption method for the spent resin drum, the paraffin solidified drum, and the spent filter drum were used.

• Membrane Journal
• /
• v.19 no.3
• /
• pp.252-260
• /
• 2009

The effects of the treatment of an acidic solution at pH 2 on polyacrylonitrile ultrafiltration (UF) membranes were investigated using a circular cross-flow filtration bench with a membrane module. A substantial reduction in the membrane permeability was observed after 80 hours' treatment of the acidic solution. In addition, the analyses of the sample solutions by ultraviolet/visible absorption spectroscopy and gas chromatography/mass spectrometry (GC/MS), which were taken from the feed tank as a function of the treatment time, showed that a new organic compound was produced in the course of the treatment. From a thorough search of the mass spectral library we presumed the new compound to be 1,6-dioxacyclododecane-7,12-dione (DCD), one of the well-known additives for polyurethane. Based on further experimental results, including the scanning electron microscope (SEM) images and the solid-state NMR spectra of the membranes used for the treatment of the acidic solution, we suggested that the decrease of the permeate flux resulted not from the deformation of the membranes, but from the fouling by DCD eluted from the polyurethane tubes in the filtration bench during the treatment. Those results imply that the reactivity to an acidic solution of the parts comprising the filtration bench is as important as that of the membranes themselves for effective treatments of acidic solutions, for efficient chemical cleaning by strong acids, and also in determining the pH limit of the solutions that can be treated by the membranes.

• Journal of Life Science
• /
• v.22 no.7
• /
• pp.981-986
• /
• 2012

To produce a new tea with a good flavor and functional properties using green tea of low quality, naked barley and barley were selected to blend with the green tea. The simultaneous distillation extraction method (SDE) using Likens and Nickerson's extraction apparatus was used to extract the volatile flavor compounds from the samples. The concentrated flavor extracts were analyzed and identified by GC and GC-MS. The GC patterns of the flavor components in two parched barleys were very different. The main volatile flavor components in two of the samples were alkyl pyrazines. Compounds including 3-methylbutanal, 2-methylbutanal, dihydro-2-methyl-3(2H)-furanone, 2,5-dimethyl pyrazine, and 3-ethyl-2.5-dimethyl pyrazine were isolated from the naked barley. Compounds including thiophenes, thiazoles, sulfides, and pyrroles with burnt odor were isolated from the barley. The parched naked barley was better than barley for adding to green tea. The main aroma components of the green tea blended with the naked barley were hexanol, hexanal, trans-2-hexenal, ${\beta}$-ionone, ${\alpha}$-ionone, alkyl pyrazines, 3-methylbutanal, 2-methylbutanal, and furfural.

• Analytical Science and Technology
• /
• v.9 no.2
• /
• pp.145-160
• /
• 1996

Inorganic analytical laboratory of Korea Research Institute of Standards and Science participated in an interlaboratory comparison program operated by Quebec Toxicology Centre of Canada in 1994 and again in 1995. The objective of this program is to enable participating laboratories to assess reproducibility and accuracy of their analytical results for trace toxic elements in human biological fluids. This laboratory determined Cd and Pb concentrations in 3 levels of human blood samples by isotope dilution inductively coupled plasma mass spectrometry. 0.5mL of blood sample is added to the digestion bomb together with 2mL of nitric acid and enriched spike isotopes and then decomposed in the microwave digestion system. The decomposed sample is diluted to 10mL and nebulized into ICP-MS. The Cd and Pb values reported by all participating laboratories are presented and compared. The values reported by this laboratory are within the acceptable range of target values.

• Food Science and Preservation
• /
• v.5 no.3
• /
• pp.239-246
• /
• 1998

Polyimide membrane system was designed for manufacturing nitrogen-enriched gas, and basic technical data was suggested for appling this system to controlled atmosphere storage. The permeability characteristics of pure oxygen and nitrogen could be explained by dual-mode sorption model. There was substantial decrease in the permeation rates of oxygen, which is the more permeable gas, through the polyimide membrane due to the presence of nitrogen in comparison with pure oxygen. However, the permeation rates of nitrogen was increased by the presence of oxygen. The ideal separation factor was in the range of 5 to 6 in the range of temperature and pressure difference studied, and the separation factor of air was lower than the ideal separation factor. The increase of ideal separation factor with increasing temperature is due to the fact that the activation energy for oxygen is larger than that for nitrogen. Nitrogen concentration decreased rapidly with increasing product recovery, and it was found that this is a major operating factor to obtain nitrogen concentration required for controlled atmosphere storage. A relation equation, by which nitrogen concentration in storehouse can be predicted, was suggested under the establishment of a hypothetical model for controlled atmosphere storage process using polyimide membrane system.

• Korean Chemical Engineering Research
• /
• v.51 no.1
• /
• pp.53-57
• /
• 2013

For the purpose of development of the extraction process of lithium ion from concentrated water eliminated from desalination process, an experimental research on the solvent extraction of lithium ion from aqueous solutions was performed. The effects of operating parameters, such as concentration of extractant, ratio of extracting solution/aqueous solution, pH of aqueous solution, were examined. The effect of sodium chloride, the major component of sea water, was also examined. Lithium ion in aqueous solutions of pH=10.2~10.6 adjusted by ammonia solution was most effectively extracted by extracting solution composed of 0.02 M TTA and 0.04 M TOPO in kerosine. The addition of sodium chloride in lithium aqueous solution significantly interfered the extraction of lithium ion.