• Korean Journal of Soil Science and Fertilizer
• /
• v.41 no.6
• /
• pp.393-398
• /
• 2008

Several researchers have proposed models or equations to predict soil $CO_2$ flux from more readily available biotic and abiotic measurement. Tree commonly used abiotic variables were N mineral and soil temperature and soil water content. This study was conducted to determine $CO_2$ emission to mineral N, soil water content and soil temperature with clay loam and sandy loam in pepper cultivation in 2004~2005. $CO_2$ flux in the upland with different levels of soil water potential was measured at least once in two weeks during the cropping period in the pepper cultivation plots. Soil water potential in the clay loam and sandy loam soils was established at -30kPa and -50kPa by measuring the soil gravimetric water content with two replications. $CO_2$ emission rate from the differently managed plots was highly correlation coefficient to between the mineral N ($R=0.830^{**}$, $0.876^{**}$) and soil temperature ($r^2=0.793^{**}$, $0.804^{**}$) in the clay loam and sandy loam, respectively. However, the relationships between $CO_2$ emission and soil water content were non-significant. $CO_2$ emissions at sandy loam soils was lower to 21~37% than at clay loam soils for both soil water conditions without differences in yield. At difference levels of soil water conditions, $CO_2$ emission at -50kPa decreased to 37.5% in comparison with that at -30kPa. From the path analysis as to contribution factors of GHGs, it appeared that contribution rate was in the order of soil temperature (54.9%), mineral N (32.7%), and soil moisture content (12.4%).

• Applied Biological Chemistry
• /
• v.9
• /
• pp.71-81
• /
• 1968

Defatted rice bran is mixed with diluted acid solution, the mixture is agitated some hrs. at constant temparature. After the mixture is filtered, thus filtrate is obtained. This filtrate is phytin extract solution. (Test-1) The alkali is added to this filtrate and filtered out, then the precipitation of phytin is obtained. (Test-2) At the test-1, the effect of kind of acid, conc. of acid, amount of extract sol'n., time of extraction, temp. of extraction, to the extract amount of phytin is tested. Consequently, the following facts are known. 1. Amount of phytin extract is greater HCI extraction than $H_{2}SO_4$ extraction. 2. At 0.3% HCI, the amount of phytin extract is greatest of all HCl extraction. 3. The sufficient amount of acid solution is 8-10 times of amount of defatted rice bran. 4. The time of extraction at room temperature is sufficient 8-12 hrs. 5. When extract temperature is $20-30^{\circ}C$, the amount of phytin extraction is greater of all temp. 6, When defatted rice bran 20 g is shanken with 160 ml of 0.3% HCl for 10 hr. at room temp., in this case the amount of phytin extract is 11.34% of defatted rice bran, it is 93% of theoretical yield. At the test-2 the effect of kind of precipitation agent, degree of nutralization to the amount of phytin prcipitation is tested. 1. Degree of nut. is best at pH 6.8-7.0. 2. When use of $Ca(OH)_2$ the amount of phytin precipitation is more than use of KOH, NaOH, or $NH_{4}OH$. 3. At pH 6.0-7.2, the solubility of phytin is followed. K-phytate > $NH_{4}-phytate$ > Na-phytate > Ca-phytate 4. When phytin extract solution is nutralized with $Ca(OH)_2$ to pH 7.0, the amount of phytin precipitation is 94.78% of theoretical yield.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.65-83
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well. 2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air. 3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying. 4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis. 5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time. 6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture. 7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation. 8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise. 11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss. 12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method. 13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated. Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year. 14. Required fan horsepower and energy for the intermittent fan operation were 3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation. 15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use. 16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.64-64
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well.2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air.3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying.4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis.5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time.6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture.7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation.8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise.11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss.12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method.13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated.Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year.14. Required fan horsepower and energy for the intermittent fan operation were3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation.15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use.16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Current Research on Agriculture and Life Sciences
• /
• v.29
• /
• pp.43-53
• /
• 2011

The possibility of making Cheongukjang by the use of soy-powder and pill type re-made from soy-powder was investigated. Some of experimental results obtained are summarized as follows; 1. Regardless of three different types for the source material of Cheonggukjang, soybean seed, soy-power, and pill, the dry weight of fermented Cheonggukjang showed continuously decreasing trends along with the time of fermentation applied. 2. In all type of source materials, the length of viscous substance during fermentation was increased along with the time of fermentation, and the rate of elongation was much reduced after 48hr of fermentation. Out of four soybean varieties tested, Taekwangkong produced longest viscous substance fermented in the type of soybean seed. No viscous substance was formed when the depth of soy-powder in the fermentation box was shallow, one centimeter. 3. Not much difference was observed in the number of microbes, Bacillus licheniformis B1, in all soybean varieties. The number was proportionally increased in the type of powder but it increased rapidly from 12 hour to 24 hour with low rate of increase thereafter in the pill type. 4. Along with the time of fermentation in all types, the color of Cheonggukjang changed from yellow to dull. At the same time, the tone of color and chroma changed into reddish and yellow, respectively. 5. Along with the time of fermentation in all types, pH of Cheonggukjang changed in alkali. 6. Along with the time of fermentation, the content of isoflavone in Cheonggukjang increased by 48hr but decreased thereafter. 7. In general, the quality of Cheonggukjang fermented in types of soy-powder and pill re-made from soy-powder was lower than that of soybean seed. More study is seemed to be needed to produce high quality Cheonggukjang by the use of soy-power.

• Korean Journal of Remote Sensing
• /
• v.34 no.2_1
• /
• pp.295-300
• /
• 2018

Net radiation is the total amount of radiation energy used as a heat flux for the Earth's energy cycle, and net radiation from the surface is an important factor in areas such as hydrology, climate, meteorological studies and agriculture. It is very important to monitoring the net radiation through remote sensing to be able to understand the trend of heat island and urbanization phenomenon. However, net radiation estimation using only remote sensing data is generally causes difference in accuracy depending on cloud. Therefore, in this paper, we retrieved and monitored high resolution surface net radiation at 1 hour interval in Eunpyeong New Town where urbanization using Communication, Ocean and Meteorological Satellite (COMS), Landsat-8 satellite and Computational Fluid Dynamics (CFD) model data reflecting the difference in building height. We compared the observed and estimated net radiation at the flux tower. As a result, estimated net radiation was similar trend to the observed net radiation as a whole and it had the accuracy of RMSE $54.29Wm^{-2}$ and Bias $27.42Wm^{-2}$. In addition, the calculated net radiation showed well the meteorological conditions such as precipitation, and showed the characteristics of net radiation for the vegetation and artificial area in the spatial distribution.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.5
• /
• pp.57-73
• /
• 2008

Nitrate concentrations were measured up to 49 mg/L (as $NO_3$-N) and 22% of the samples exceeded drinking water standard in shallow and bedrock groundwater of the northern Nonsan area. Nitrate concentrations showed a significant difference among land use groups. To predict nitrate concentration in groundwater, multiple regression analysis was carried out using hydrogeologic parameters of soil media, topography and land use which were categorized as several groups, well depth and altitude, and field parameters of temperature, pH, DO and EC. Hydrogeologic parameters were quantified as area proportions of each category within circular buffers centering at wells. Regression was performed to all the combination of variables and the most relevant model was selected based on adjusted coefficient of determination (Adj. $R^2$). Regression using hydrogelogic parameters with varying buffer radii show highest Adj. $R^2$ at 50m and 300m for shallow and bedrock groundwater, respectively. Shallow groundwater has higher Adj. $R^2$ than bedrock groundwater indicating higher susceptibility to hydrogeologic properties of surface environment near the well. Land use and soil media was major explanatory variables for shallow and bedrock groundwater, respectively and residential area was a major variable in both shallow and bedrock groundwater. Regression involving hydrogeologic parameters and field parameters showed that EC, paddy and pH were major variables in shallow groundwater whereas DO, EC and natural area were in bedrock groundwater. Field parameters have much higher explanatory power over the hydrogeologic parameters suggesting field parameters which are routinely measured can provide important information on each well in assessment of nitrate contamination. The most relevant buffer radii can be applied to estimation of travel time of contaminants in surface environment to wells.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.4
• /
• pp.544-550
• /
• 2012

This study was conducted to investigate the characteristic factors which have been influenced on nitrous oxide ($N_2O$) emissions related to the environment change of nitrogen application level, rainfall and temperature during the potato cultivation at black volcanic ash soil from 2010 to 2011. During the potato cultivation, the more amount of nitrogen fertilizer applied, $N_2O$ emissions amounts were released much. $N_2O$ emissions with the cultivation time were released much at the first and middle of cultivation with heavy rainfall, but it was released very low until the end of cultivation and drought season. $N_2O$ emissions mainly were influenced by the rainfall and soil water content. The correlation (r) with $N_2O$ emissions, soil wate, soil temperature in 2010 were very significant at $0.6251^{**}$ and $0.6082^{**}$ respectively, but soil EC was not significant to 0.10824. In 2011, soil temperature was very significant at $0.4879^{**}$, but soil water and soil EC were not significant at 0.0468 and 0.0400 respectively. Also, $NH_4$-N was very significant at $0.7476^{**}$, but $NO_3$-N and soil nitrogen ($NO_3-N+NH_4-N$) were not significant at 0.0843 and 0.1797, respectively. During the potato cultivation period, the average emissions factor of 2 years released by the nitrogen fertilizer application was presumed to be 0.0040 ($N_2O-N\;kg\;N^{-1}\;kg^{-1}$). This factor was lower about 2.5 times than the IPCC guideline default value (0.0100 $N_2O-N\;kg\;N^{-1}\;kg^{-1}$).

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.50 no.3
• /
• pp.161-169
• /
• 2005

With various Korean domestic soybeans, growth and yields analysis were conducted to select the suitable soybean cultivars for cultivation in paddy field. Distinctive aspects of the soybean growth were observed in paddy field such as retarded growth of top plants and roots, relatively higher T/R ratio followed by overgrowth of top plant. However, growth and yields were significantly different among the cultivars showing 134kg/10a in Paldokong and 385 kg/10a in Doremikong. At V5. and R2 stage, highly positive correlations $(r=0.76^{**}\~0.91^{**})$ were observed between leaf area and dry weight of top plant and/or root. T/R ratio was negatively correlated with dry weight of root $(r=-0.37^*)$ at V5 stage, while significantly correlated with leaf area $(r=-0.37^{**})$ and dry weight of top plant $(r=0.65^{**})$at R2 stage. Among the characters, only 100-seed weight was significantly correlated with yield. Considering the growth characters, 37 cultivars could be included in 3 different groups and genotypic properties such as maturity and growth habit were similar in each group. Nine cultivars in group 1 showed retarded growth from V5 to R2 stage, relatively lower T/R ratio, and good seed ripening. Average yields of the cultivers was 257kg/10a. In group 2, 12 cultivars showed higher T/R ratio due to overgrowth of top plant and lowest average yields (230 kg/l0a) due to poor seed ripening. Sixteen cultivars in group 3 grew fast from V5 to R2 stage representing late maturity traits, low T/R ratio, and good seed ripening. Average yields of the cultivars was highest among groups showing 270kg/l0a. In results, stable self-sufficiency of soybean yields could be expected by selective cultivation with high yielding cultivars ranging from 301 to 385kg/10a, such as Shinpaldalkong 2, Sohokong, Doremikong, Keumkangkong, Bukangkong, Dajangkong, and Geomjeongkong 2, or with cultivars included in group 3.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.52 no.2
• /
• pp.140-145
• /
• 2007

This study was carried out to develop effective test method by soybean stink bug and to screen resistant genetic resources against soybean stink bug. The damage pod rate by stink bug showed 40% of most soybean varieties and was selected about 10% low of 10 varieties by 298 variety and degree in soybean at first year Stink bug damage rate research for 102 varieties that stink bug damage rate lowed at first year showed 10% low of 12 varieties and from 20% to 30% of the other varieties. So testing material is "Ilpumgeumjeongkong" to develop for effective test method soybean stink bug and result for stink bug damage rate research of according to growth stage showed rapidly high more full seed than full pod. Full seed stage (R6) was highest to 35.5% for stink bug damage rate. Result of resistant genetic resources selection according to stink bug damage pod rate was lowed of best to 10.3% for "Peking, Sorogkong, Hwangsaegjunjeari and Sobaeknamulkong" in the order. Also, stink bug damage seed rate was similar too. So "Peking, Sorogkong, Hwangsaegjunjeari and Sobaeknamulkong" were thought resistant variety against stink bug. Additional study carried out with "Peking and Sorogkong" so that concretely investigate about stink bug's refuse reaction. This result showed 10.0% for Peking and 14.2% for Sorogkong at R6 stage. But, damage pod rate was rapidly lowed.