• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2016.05a
• /
• pp.88-89
• /
• 2016

선택적 환원 촉매(SCR : Selective Catalytic Reduction) 시스템은 대기오염을 예방하기 위한 배기가스 처리장치 중 하나이다. 본 연구에서는 전산유체역학(CFD : Computational Fluid Dynamics)를 사용하여 SCR 시스템 의 효율향상을 위하여 ANSYS-CFX package를 이용하여 점성 유동 해석을 수행하였다. SCR 시스템의 점성 유동 흐름의 전산 유체 역학을 이용하여 시뮬레이션하기 위하여 Navier-Stokes 방정식을 지배방정식으로 사용하였다. CATIA V5를 사용하여 SCR 시스템의 형상을 3D 모델링을 하였고, 암모니아와 배기가스의 혼합 비율을 확인하기 위해 요소수 분사 노즐의 위치를 변경하였다. 요소수 분사 노즐은 배기관의 입구로부터 1/3, 1/2, 2/3에 위치한다. 또한, 분사 노즐의 위치가 배기관 입구의 1/3에 위치할 때 노즐의 분사구수에 따른 효율을 확인하기 위하여 분사구수를 4Hole, 6Hole, 8Hole일 경우를 확인하여 비교하였다. 시뮬레이션의 결과로는 배기관 입구에 가까울수록, 분사구수가 많을수록 효율이 좋아짐을 확인하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.4
• /
• pp.81-89
• /
• 2014

Tandem-ejector has been devised for engine-bay cooling. In this study, 1-D model has been developed to analyze Tandem-ejector. In the model, the primary, the secondary and the tertiary flow conditions have been analyzed with isentropic process. The mixing process has been analyzed with conservation laws based on the control volume analysis. The total pressure loss of the primary flow has been analyzed under the matching condition between the static pressure of Tandem-ejector discharge flow and atmospheric pressure. Consequently, 1-D model can predict Tandem-ejector performance accurately and provide the performance map.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.7
• /
• pp.939-944
• /
• 2018

Clean fire extinguishing agents refer to chemical that can replace Halon 1211 and Halon 1310 according to the Montreal Protocol fermented to protect the Earth's ozone layer. In Korea and abroad, system standardization and performance evaluation of clean fire extinguishing agents are being carried out. This paper proposes an optimal nozzle shape by modeling and numerical analysis of various nozzle shapes based on general clean fire extinguishing system. The ejection speed of the nozzle can be improved by studying three - dimensional modeling of the nozzle for two shapes, Type A and B. Flow analysis was performed on the two types of nozzles and the gas velocity and pressure distribution were measured with different nozzle diameters. It was confirmed that the jetting speed was changed at the nozzle outlet according to the number and diameter of the nozzle holes. The flow rate increased with increasing the pressure regardless of the nozzle hole diameter. Based on the results obtained from the experiment, the K-factor value was deduced. Finally, a nozzle with a 12-hole structure with a 5-mm nozzle hole was proposed.

• Journal of KSNVE
• /
• v.7 no.6
• /
• pp.888-893
• /
• 1997

진공청소기에서 발생하는 주 소음원은 홴(fan)에 의한 공력 소음및 모터의 진동에 기인하는 청소기 본체의 소음과 청소기 흡입 노즐(nozzle)에서 발생하는 공력 소음으로 나눌수 있다. 청소기 본체의 주 소음원인 원심 홴(centrifugal fan)은 고속으로 회전하며 구조가 복잡함으로 인해 소음 해석에 필수적인 유동의 해석이 어려우나 이산 와류법을 이용한 소음원 해석등의 연구가 진행중이다. 진공청소기 노즐부에서는 일반적인 분류(jet)의 토출과는 상이하게 공기를 흡입하는 구조로 소음 발생 기구의 모델링 (modeling)에 대한 연구는 거의 전무하다. 공력 소음은 Lighthill에 의하면 비정상 유체가 운동할 때 나타나는 변형에 기인한다고 하며 주변에 고정 경계면이 없는 상태에서 유체가 흐를 때 발생하는 소음을 이론적으로 연구하였다. 그후 Curle에 의해서 고체 벽면의 영향을 고려한 방정식의 해가 구해졌다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.33-37
• /
• 1993

연결부를 지닌 대형의 노즐형상 제품은 대형산업기기에서 용기의 일부 및 추진체 및 인공위성 발사 대등에서 쓰이는 제품으로 목적하고자 하는 최종 조립품의크기에 따라 제품자체의 지름이 1m 에서 수m 에 이르는 대형으로 제작된다. 대형노즐형 제품은 제품 자체의 강도, 정확한 치수 및 소요재료의 다수등도 중요한 요소이나, 가공하중의 크기에 따라 다르지만 제품을 만들기 위해서는 수만톤을 필요로하기 때문에 제품제조의 가능여부가 성형기의 능력에 의존하게 된다. 본 연구는 비교적 소형장비로써 대형 노즐형단조 품의 제작이 가능한 새로운 성형공정을 개발하는데 그 목적이 있으며 공정개발은 비교적 소형 장비로써 대형단조품의 제작이 가능하도록 하는데 촛점을 맞추고서 이루어 졌다. 이를 위해 여러가지 가능한 방법 들을 제안하고, 각각의 공정 방법들에 대해서 Plasticine 모델 시험을 통하여 소성유동에 의한 성형성과 하중을 검토한 후에 국내에서 사용가능한 장비 및 하중능력, 그리고 성형성 등을 고려하여 적절한 공정방법을 선택하였다. 선택된 공정에서 점진적 팽창단조를 위한 예비 성형체의 결정 및 공정변수의 결정등을 납 모델링실험을 행하여하였으며 실재 재료의 축소모형실험을 수행하여 공정을 확인 하였다.

• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.144-153
• /
• 2009

To study the plume effects in the rarefied region, the Direct Simulation Monte Carlo(DSMC) method is usually adopted because the plume field usually contains the entire range of flow regime from the near-continuum in the vicinity of nozzle exit through transitional state to free molecular at far field region from the nozzle. The objective of this study is to investigate the behaviors of a small monopropellant thruster plume in the rarefied region numerically using DSMC method. To deduce accurate results efficiently, the preconditioned scheme is introduced to calculate continuum flow fields inside thruster to predict nozzle exit properties used for inlet conditions of DSMC method. By combining these two methods, the rarefied flow characteristics of plume such as strong nonequilibrium near nozzle exit, large back flow region, etc, can be investigated.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.9
• /
• pp.906-915
• /
• 2009

To study the plume effects in the vacuum area, the Direct Simulation Monte Carlo(DSMC) method is usually adopted because the plume field usually contains the entire range of flow regime from the near-continuum in the vicinity of nozzle exit through transitional state to free molecular at far field region from the nozzle. The objective of this study is to investigate the behaviors of a small monopropellant thruster plume in the vacuum area numerically using DSMC method. To deduce accurate results efficiently, the preconditioned scheme is introduced to calculate continuum flow fields inside thruster to predict nozzle exit properties used for inlet conditions of DSMC method. By combining these two methods, the vacuum flow characteristics of plume such as strong nonequilibrium near nozzle exit, large back flow area, etc, can be investigated.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.4
• /
• pp.84-91
• /
• 2002

Thrust vector characteristics of jet vanes installed in a shroud are very unique and much more complicated than those of the jet vane acting without any shroud by the fact of additional physical phenomena. The fluid dynamic interferences induced by jet vanes and shroud as well as jet vane's aerodynamic performance are investigated to characterize thrust vector control by semi-empirical model, three dimensional numerical analysis including real complex geometry, and ground firing test of real motors.

• Fire Science and Engineering
• /
• v.32 no.4
• /
• pp.17-24
• /
• 2018

This paper presents a numerical analysis of flow inside a water nozzle for fire fighting and observes the effect of the variation in primary components on internal flow. In order to observe the performance of water nozzles, they have been systematically designed and modelled, applying boundary conditions obtained from field experiments (inlet pressure at pump : 4 bar, and pressure outlet : atmospheric pressure). In addition, the governing equations were calculated to obtain velocity, pressure inside the nozzle. Two main parameters (the presence and length of sub-pipes) were considered with the aim to observe the detail internal flow characteristics. It is found that the base model is not significant on flow characteristics, but a negative effect (i. e. the reverse flow) at the entrance region of sub-pipe. On the other hand, the reverse flow was vanished when making the length of sub-pipe double.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.108-114
• /
• 2010

The injection nozzle of an electro-hydraulic injector is being opened and closed by movement of a injector's needle which is balanced by pressure at the nozzle seat and at the needle control chamber, at the opposite end of the needle. In this study, the effects of needle movement in a piezo-driven injector on unsteady cavitating flows behavior inside nozzle were investigated by cavitation numerical model based on the Eulerian-Lagrangian approach. Aimed at simulating the 3-D two-phase flow behavior, the three dimensional geometry model along the central cross-section regarding of one injection hole with real design data of a piezo-driven diesel injector has been used to simulate the cavitating flows for injection time by at fully transient simulation with cavitation model. The cavitation model incorporates many of the fundamental physical processes assumed to take place in cavitating flows. The simulations performed were both fully transient and 'pseudo' steady state, even if under steady state boundary conditions. As this research results, we found that it could analyze the effect the pressure drop to the sudden acceleration of fuel, which is due to the fastest response of needle, on the degree of cavitation existed in piezo-driven injector nozzle.