• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.29 no.1
• /
• pp.51-57
• /
• 2023

Because of the global pollution caused by plastic disposal, demand for eco-friendly transformation in the packaging industry is increased. As part of that, the utilization of polylactic acid (PLA) as a food packaging material is increased. However, it is necessary to improve the crystallinity of PLA by adding nucleating agents or to improve the modulus by adding fillers because of the excessive brittleness of the PLA matrix. Thus, the cellulose nanofiber (CNF) was fabricated and dried to obtain a powder form and applied to the CNF/PLA nanocomposite. The effect of CNF on the morphological, thermal, rheological, and dynamic mechanical properties of the composite was analyzed. We can confirm the impregnated CNF particle in the PLA matrix through the field emission scanning electron microscope (FE-SEM). Differential scanning calorimetry (DSC) analysis showed that the crystallinity of not annealed CNF/PLA nanocomposite was increased approximately 2 and 4 times in the 1st and 2nd cycle, respectively, with the shift to lower temperature of cold crystallization temperature (T_cc) in the 2nd cycle. Moreover, the crystallinity of annealed CNF/PLA nanocomposite increased by 13.4%, and shifted T_cc was confirmed.

• Korean Journal of Food Science and Technology
• /
• v.5 no.1
• /
• pp.6-15
• /
• 1973

In an attempt to develop composite flours based on raw materials available in Korea, six domestic resources were investigated with respect to their physical and chemical properties, nutritive value and economy. The results are summarized as follows: 1) Flours from naked barley, sweet potato, potato, corn, defatted rice bran and defatted soybean were compared in respect of their proximate composition, thiamine content and protein score. 2) In color comparison, naked barley and defatted soy flours were comparable to wheat flour whereas corn and sweet potato flours were a little inferior. In raising power, naked barley and defatted soy flours were similar to wheat flour and others were inferior. 3) In maximum viscosity of flours by amylograph, naked barley, corn and potato flours were higher than wheat flour and others were lower. In viscosity in cooling, corn flour was similar to wheat flour and naked barley and potato flours were lower. Addition of $10{\sim}20%$ defatted soy flour into other flours generally caused the lowering of viscosity. Addition of emulsifiers such as glyceryl monostearate, calcium stearyl lactylate, Methocel and Emulthin into the flours manifested different effects on the amylogram. 4) In nutritional test by rat, diets consisting of naked barley, sweet potato, potato or corn flours, each containing defatted soy flour (at 10% level with exception of 20% for sweet potato flour) and naked barley flour fortified with lysine were similar to wheat flour in digestibility, but were superior in NPU and biological value. 5) In price estimation, sweet potato and corn flours were competitive with wheat flour, but naked barley flour was a little expensive. On the other hand, barley and sweet potato are promising in terms of domestic production.

• Korean Journal of Food Science and Technology
• /
• v.16 no.1
• /
• pp.99-107
• /
• 1984

Naked barley flour(Baekdong cultivar) was examined with respect to its pasting properties by means of Brabender amylograph after adding barley lipids, fatty acids, vegetable oils and emulsifiers at 1% level. Amylogram of barley flour showed a similar gelatinization temperature but higher paste viscosities at all reference points as compared with wheat flour. Barley flour showed lower amylograph curves by defatting with n-hexane, namely reductions in initial gelatinization point, maximum viscosity and setback value. But re-addition of n-hexane extract to the defatted flour essentially reproduced the curve obtained in the undefatted flour. Addition of polar and nonpolar lipids exhibited different effects on the pasting properties of barley flour. Polar lipids generally increased maximum viscosity a little while non-polar lipids increased the maximum viscosity substantially. Addition of increasing amounts of nonpolar lipids was found to progressively increase the maximum viscosity. Addition of fatty acids increaed th maximum viscosity and delayed the peak time. The maximum viscosity of defatted barley flour impregnated with unsaturated fatty acids was higher than that of defatted barley flour impregnated with saturated fatty acids Increasing amounts of linoleic acid were fount to progressively increase the maximum viscosity and to delay the peak time of defatted barley flour. Addition of six vegetable oils lowered the gelatinization temperature and rasied the maximum viscosity and temperature at maximum viscosity. Addition of increasing amount of peanut oil was found to decrease the maximum viscosity. The effect of emulsifiers was greater in undefatted flour than in defatted flour. The maximum viscosity of defatted flour was slightly affected by Methocel 50, Methocel 1500 and Emulthin, and substantially increased by Methocel 4000, sodium polyacrylate and calcium stearyl lactylate.

• Korean Journal of Heritage: History & Science
• /
• v.51 no.2
• /
• pp.78-91
• /
• 2018

Sangjogam, located in Goseong, Gyeongsangnam-do, was designated as Natural Monument #411, because of its diverse geological heritage, such as fossils, ripple marks, dykes, and columnar joints. In the area, Byeongpungbawi, with its beautiful columnar joints vertical to the bedding plane of the underlying sedimentary rocks and spectacular coastal view, was named after its overall shape reminiscent of a huge folding screen. The purpose of this study was to investigate the formation process of the columnar joints using the anisotropy of magnetic susceptibility (AMS) method. AMS measurements showed that the k1 and k3 values representative of directions of the long and short axes of a magnetic particle at each point strongly clustered, and the oblate magnetic foliation structure in Byeongpungbawi developed during sill-type intrusion rather than lava flow. In summary, Byeongpungbawi was produced by sill-type intrusion along the bedding plane of the underlying sedimentary layer, and the subsequent formation of columnar joints was accompanied by the cooling and contraction of intruding rhyolite magma. This study potentially provides a basic research tool in understanding the formation mechanism of columnar joints which are widely distributed in southern Korea.

• Korean Journal of Agricultural Science
• /
• v.13 no.1
• /
• pp.82-89
• /
• 1986

This experiment was carried out to determine the optimum freezing and thawing rates of the hamster embryos. The female hamsters were induced to superovulate by intraperitoneal injections of 30 i.u. PMSG and mated with males of the same strain of 4 days the PMSG injection. They were killed and embryos were flushed from the oviduct and uterine horn on 3 days after mating. Embryos were flushed with a modified Dulbecco's phosphate-buffered saline and equilibrated with 1.5 M-dimethylsulphoxide by a 3-step procedure. The freezing rates of the samples were $1^{\circ}C/min$ from room temperature to $-6^{\circ}C$ and the samples were seeded at $-6^{\circ}C$. After being held for 3 min at the seeding temperature, the rates were $0.3^{\circ}C/min$ from $-6^{\circ}C$ to $-35^{\circ}C$. From $-35^{\circ}C$ to $-70^{\circ}C$, the rates were divided into $0.1^{\circ}C/min$, $1^{\circ}C/min$ and $10^{\circ}C/min$, respectively. At $-70^{\circ}C$ the samples were plunged directly into liquid nitrogen. The samples were thawed at $4^{\circ}C/min$ and $12^{\circ}C/min$ from $-196^{\circ}C$ to $37^{\circ}C$, and for 2 min in $37^{\circ}C$ water bath, respectively. The average numbers of ovulation points and embryos recovered were 35.1 and 27.0 appearing 77.0% recovery rates. Eight cell embryos in the embryos recovered were 24.8. The survival rates of embryos according to the freezing rates were 55.5~67.7% at $0.1^{\circ}C/min$, 58.8~64.9% at $1^{\circ}C/min$ and 40.5~44.7% at $10^{\circ}C/min$, respectively. The survival rates at $10^{\circ}C/min$ were significantly low. The survival rates of embryos according to the thawing rates were 53.5% at $4^{\circ}C/min$, 53.7% at $12^{\circ}C/min$ and 59.1% in $37^{\circ}C$ water bath. The survival rates, in $37^{\circ}C$ water bath were slightly higher, but we did not find any differences among them. In conclusion, the best freezing rates of hamster embryos were $1^{\circ}C/min$ from the room temperature to $-6^{\circ}C/min$, $0.3^{\circ}C/min$ from $-6^{\circ}C/min$ to $-35^{\circ}C$ and $-0.1^{\circ}C/min$ or $1^{\circ}C/min$ from $-35^{\circ}C$ to $-70^{\circ}C$. The hamster embryos thawed for 2 min in $37^{\circ}C$ water bath showed the best survival rates.

• Journal of Chest Surgery
• /
• v.30 no.5
• /
• pp.471-478
• /
• 1997

Introduction: The use of rabbits as a cardiopulmonary bypass(CPB) animal model is extremely dif%cult mainly due to technical problems. On the other hand, deep hypothermic circulatory arrest(CA) is used to facilitate surgical repair in a variety of cardiac diseases. Although steroids are generally known to be effective in the treatment of cerebral edema, the protective effects of steroids on the brain during CA are not conclusively established. Objectives of this study are twofold: the establishment of CPB technique in rabbits and the evaluation of preventive effect of steroid on the development of brain edema during CA. Material '||'&'||' Methods: Fifteen New Zealan white rabbits(average body weight 3.5kg) were divided into three experimental groups; control CA group(n=5), CA with Trendelenberg position group(n=5), and CA with Trendelenberg position + steroid(methylprednisolone 30 mglkg) administration group(n=5). After anesthetic induction and tracheostomy, a median sternotomy was performed. An aortic cannula(3.3mm) and a venous ncannula(14 Fr) were inserted, respectively in the ascending aorta and the right atrium. The CPB circuit consisted of a roller pump and a bubble oxygenator. Priming volume of the circuit was approximately 450m1 with 120" 150ml of blood. CPB was initiated at a flow rate of 80~85ml/kg/min, Ten min after the start of CPB, CA was established with duration of 40min at $20^{\circ}C$ of rectal temperature. After CA, CPB was restarted with 20min period of rewarming. Ten min after weaning, the animal was sacrif;cod. One-to-2g portions of the following tissues were rapidly d:ssected and water contents were examined and compared among gr ups: brain, cervical spinal cord, kidney, duodenum, lung, heart, liver, spleen, pancreas. stomach. Statistical significances were analyzed by Kruskal-Wallis nonparametric test. Results: CPB with CA was successfully performed in all cases. Flow rate of 60-100 mlfkgfmin was able to be maintained throughout CPB. During CPB, no significant metabolic acidosis was detected and aortic pressure ranged between 35-55 mmHg. After weaning from CPB, all hearts resumed normal beating spontaneously. There were no statistically significant differences in the water contents of tissues including brain among the three experimental groups. Conclusion: These results indicate (1) CPB can be reliably administered in rabbits if proper technique is used, (2) the effect of steroid on the protection of brain edema related to Trendelenburg position during CA is not established within the scope of this experiment.

• Economic and Environmental Geology
• /
• v.35 no.3
• /
• pp.211-220
• /
• 2002

The Xiaoxinancha Cu-Au deposit in the Jilin province, located in NNE 800 km of Beijing, is hosted by diorite. The ore mineralization of Xiaoxinancha Cu-Au deposit show a stockwork occurrence that is concentrated on the potassic and phyllic alteration zones. The Xiaoxinancha Cu-Au deposit in the south is being mined with its reserves grading 0.8% Cu, 3.64 g/t Au and 16.8 g/t Ag and in the north, grading 0.63% Cu, 3.80 g/t Au and 6.8 glt Ag. The alteration assemblage occurs as a supergene blanket over deposit. Hydrothermal alteration at the Xiaoxinancha Cu-Au deposit is centered about the stock and was extensively related to the emplacement of the stock. Early hydrothermal alteration was dominantly potassic and followed by propylitic alteration. Chalcocite, often associated with hematite, account for the ore-grade copper, while chalcopyrite, bornite, quartz, epidote, chlorite and calcite constitute the typical gangue assemblage. Other minor opaque phases include pyrite, marcasite, native gold, electrum, hessite, hedleyite, volynskite, galenobismutite, covellite and goethite. Fluid inclusion data indicate that the formation of this porphyry copper deposit is thought to be a result of cooling followed by mixing with dilute and cooler meteoric water with time. In stage II vein, early boiling occurred at 497$^{\circ}$C was succeeded by the occurrence of halite-bearing type III fluid inclusion with homogenization temperature as much as 100$^{\circ}$C lower. The salinities of type 1II fluid inclusion in stage II vein are 54.3 to 66.9 wt.% NaCI + KCI equiv. at 383$^{\circ}$ to 495$^{\circ}$C, indicating the formation depth less than 1 km. Type I cupriferous fluids in stage III vein have the homogenization temperatures and salinity of 168$^{\circ}$ to 365$^{\circ}$C and 1.1 to 9.0 wt.% NaCI equiv. These fluid inclusions in stage III veins were trapped in quartz veins containing highly fractured breccia, indicating the predominance of boiling evidence. This corresponds to hydrostatic pressure of 50 to 80 bars. The $\delta$$^{34}S$ value of sulfide minerals increase slightly with paragenetic time and yield calculated $\delta$$^{34}S_{H2S}$ values of 0.8 to 3.7$\textperthousand$. There is no mineralogical evidence that fugacity of oxygen decreased, and it is thought that the oxygen fugacity of the mineralizing fluids have been buffered through reaction with magnetite. We interpreted the range of the calculated $\delta$$^{34}S_{H2S}$ values for sulfides to represent the incorporation of sulfur from two sources into the Xiaoxinancha Cu-Au hydrothermal fluids: (1) an isotopically light source with a $\delta$$^{34}S$ value of I to 2$\textperthousand$, probably a Mesozoic granitoid related to the ore mineralization. We can infer from the fact that diorite as the host rock in the Xiaoxinancha Cu-Au deposit area intruded plagiogranite; (2) an isotopically heavier source with a $\delta$$^{34}S$ value of > 4.0$\textperthousand$, probably the local porphyry.

• Clean Technology
• /
• v.19 no.3
• /
• pp.264-271
• /
• 2013

In this study, we optimized the removal condition of contaminants attached on the scrap surface to recycle the scrap generated from the Zr alloy tube manufacturing process back to the nuclear grade. The main contaminant is remnant of watersoluble cooling lubricant that is used in the pilgering manufacture during the tube production, and it is assumed to be compressed and carbonized on the surface of tube. Zirlo alloy tube of ${\phi}9.50mm$, which has high occurrence frequency of scrap, was selected as the object to be cleaned, and cleaning abilities of reagents were evaluated by measuring the characteristics of contaminants remained and by analyzing the surface of the tube after cleaning process. For evaluation of each cleaning agent, we selected two types of sodium hydroxide series and three types of potassium hydroxide series. Furthermore, to confirm dependence on tempe-rature and ultrasonic intensities, cleaning at the room temperature, $40^{\circ}C$, and $60^{\circ}C$ was conducted, and results showed that higher the cleaning temperature and higher the ultrasonic intensity, better the cleaning effect. As a result of the bare-eye inspection, while the use of sodium hydroxide provided satisfactory condition on the tube surface, the use of potassium hydroxide series provided satisfactory condition on the tube surface only when the ultrasonic intensity was over 120 W. In the cleaning effect analysis using the gravimetric method, cleaning efficiency of sodium hydroxide series was as high as 97.6% ($60^{\circ}C$, 120 W), but since the tube surface condition was poor after the use of potassium hydroxide, the gravimetric method was not appropriate. In the analytical result of surface contaminants on the tube surface, C, O, Ca, and Zr were detected, and mainly C and O dominated the proportion of contaminants. It was also found that the degree of cleaning on the tube affected the componential ratio of C and O; if the degree of cleaning is high, or if cleaning is well-conducted, the proportion of C is decreased, and the proportion of O is increased. Based on these results, optimal cleaning for application in the industry can be expected by categorizing cleaning process into three steps of Alkali cleaning, Rinsing, and Drying and by adjusting cleaning parameters in each step.

• Korean Chemical Engineering Research
• /
• v.48 no.4
• /
• pp.499-505
• /
• 2010

In this study, hydrodynamics and reaction characteristic of K-based solid sorbents for $CO_2$ capture were investigated using a continuous system composed of two bubbling fluidized-bed reactors(1.2 m tall bed with 0.11 m i.d.). Potassium-based dry sorbents manufactured by the Korea Electric Power Research Institute were used, which were composed of $K_2CO_3$ of 35% for $CO_2$ absorption and supporters of 65% for mechanical strength. The continuous system consists of two bubbling fluidized-bed reactors, solid injection nozzle, riser, chiller, analyzer and heater for regeneration reaction. The minimum fluidizing velocity of the continuous system was 0.0088 m/s and the solid circulation rate measured was $10.3kg/m^2{\cdot}s$ at 1.05 m/s velocity of the solid injection nozzle. The $CO_2$ concentration of the simulated gas was about 10 vol% in dry basis. Reaction temperature in carbonator and regenerator were maintained about $70^{\circ}C$ and $200^{\circ}C$, respectively. Differential pressures, which were maintained in carbonator and regenerator, were about $415mmH_2O$ and $350mmH_2O$, respectively. In order to find out reaction characteristics of dry sorbents, several experiments were performed according to various experimental conditions such as $H_2O$ content(7.28~19.66%) in feed gas, velocity (0.053~0.103 m/s) of simulated gas, temperature($60{\sim}80^{\circ}C$) of a carbonator, temperature($150{\sim}200^{\circ}C$) of a regenerator and solid circulation rate($7.0{\sim}10.3kg/m^2{\cdot}s$). The respective data of operating variables were saved and analyzed after maintaining one hour in a stable manner. As a result of continuous operation, $CO_2$ removal tended to increase by increasing $H_2O$ content in feed gas, temperature of a regenerator and solid circulation rate and to decrease by increasing temperature of a carbonator and gas velocity in a carbonator.

• Economic and Environmental Geology
• /
• v.20 no.1
• /
• pp.35-60
• /
• 1987

The geochemical characteristics including minerals, major and trace elements chemistries of the Proterozoic, Jurassic and Cretaceous granites in Korea are systematically summarized and intended to decipher the origin and crystallization process in connection with the tectonic evolution. The granites in Korea are classified into three different ages of the granites with their own distinctive geochemical patterns: 1) Proterozoic granitoids; 2) Jurassic granites(cratonic and mobile belt); 3) Cretaceous-Tertiary granites. The Proterozoic granite gneisses (I-type and ilmenite-series) formed by metamorphism of the geochemically evolved granite protolith. The Proterozoic granites (S-type and ilmenite-series) produced by remobilization of sialic crust. The Jurassic granites (S-type and ilmenite-series) were mainly formed by partial melting of crustal materials, possibly metasedimentary rocks. The Cretaceous granites (I-type and magnetite-series) formed by fractional crystallization of parental magmas from the igneous protolith in the lower crust or upper mantle. The low temperature ($315{\sim}430^{\circ}C$) and small temperature variations (${\pm}20{\sim}30^{\circ}C$) in the cessation of exsolution of perthites for the Proterozoic and Jurassic granites might have been caused by slow cooling of the granites under regional metamorphic regime. The high ($520^{\circ}C$) and large temperature variations (${\pm}110^{\circ}C$) of perthites for the Cretaceous granites postulate that the rapid cooling of the granitic magma. In terms of the oxygen fugacity during the feldspar crystallization in the granite magmas, the Jurassic mobile belt granites were crystallized in the lowest oxygen fugacity condition among the Korean granites, whereas the Cretaceous granites in the Gyeongsang basin at the high oxygen fugacity condition. The Jurassic mobile belt granites are located at the Ogcheon Fold Belt, resulting by closing-collision situation such as compressional tectonic setting, and emplaced into a Kata-Mesozonal ductile crust. The Jurassic cratonic granites might be more evolved either during intrusion through thick crust or owing to lower degree of partial melting in comparison with the mobile belt granites. The Cretaceous granites are possibly comparable with a continental margin of Andinotype. Subduction of the Kula-Pacific ridge provided sufficient heat and water to trigger remelting at various subcrustal and lower crustal igneous protoliths.