• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2015.10a
• /
• pp.95-96
• /
• 2015

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.2
• /
• pp.131-143
• /
• 2013

Vibration condition monitoring of low-speed rotational slewing bearings is essential ever since it became necessary for a proper maintenance schedule that replaces the slewing bearings installed in massive machinery in the steel industry, among other applications. So far, acoustic emission(AE) is still the primary technique used for dealing with low-speed bearing cases. Few studies employed vibration analysis because the signal generated as a result of the impact between the rolling element and the natural defect spots at low rotational speeds is generally weak and sometimes buried in noise and other interference frequencies. In order to increase the impact energy, some researchers generate artificial defects with a predetermined length, width, and depth of crack on the inner or outer race surfaces. Consequently, the fault frequency of a particular fault is easy to identify. This paper presents the applications of empirical mode decomposition(EMD) and ensemble empirical mode decomposition(EEMD) for measuring vibration signals slewing bearings running at a low rotational speed of 15 rpm. The natural vibration damage data used in this paper are obtained from a Korean industrial company. In this study, EEMD is used to support and clarify the results of the fast Fourier transform(FFT) in identifying bearing fault frequencies.

• Korean Journal of Materials Research
• /
• v.8 no.7
• /
• pp.634-640
• /
• 1998

A well- shaped trench was investigated in view of the defect distribution along trench sidewall and bottom using high resolution transmission electron microscopy. The trench was formed by HBr plasma and additive gases in magnetically enhanced reactive ion etching system. Adding $0_2$ and other additive gases into HBr plasma makes it possible to eliminate sidewall undercut and lower surface roughness by forming the passivation layer of lateral etching, resulted in the well filled trench with oxide and polysilicon by subsequent deposition. The passivation layer of lateral etching was mainly composed of $SiO_xF_y$ $SiO_xBr_y$ confirmed by chemical analysis. It also affects the generation and distribution of lattice defects. Most of etch induced defects were found in the edge region of the trench bottom within the depth of 10$\AA$. They are generally decreased with the thickness of residue layer and almost disappeared below the uni¬formly thick residue layer. While the formation of crystalline defects in silicon substrate mainly depends on the incident angle and energy of etch species, the region of surface defects on the thickness of residue layer formed during trench etching.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.504-509
• /
• 2016

Defects in dissimilar metal welds are reported to be on the increase during the operating lifespan and aging of nuclear power plants. In Korea, reported cases of defects due to dissimilar metal welds include the drain nozzle of a steam generator and RCS hot tube sampling nozzles. Therefore, there is an urgent need to develop a reliable automated nondestructive inspection technique and a system for the inspection of dissimilar metal welds of small diameter nozzles in a high radiation area of a nuclear power plant. In this study, to ensure effective defect inspection of small diameter nozzles (RCS high-temperature tube sampling nozzle) of a nuclear power plant, three different methods were developed. These include: (1) optimum inspection probe design by beam simulation, (2) multi-directions UT optimum inspection technique for the inspection of small diameters of different welded parts, and (3) remote control automatic inspection system. The developed technique and systems have been verified to be suitable for use in the inspection of defects in smaller diameter nozzles in nuclear power plants.

• Journal of Radiation Protection and Research
• /
• v.11 no.2
• /
• pp.139-145
• /
• 1986

An improved mothod of assessing fuel status by analyzsis of the fission product in the reactor coolant system is proposed. The release mechanism of specific fission products is established for determination of the coefficients in the equations which relate the radioactivities with the amount of defected fuel. Knock-out and migration models are employed in the formulation of the release mechanism. The influence of the tramp uranium is quantified. Sample calculations were made for KNU 1 reactor system using the I-131 and I-133 concentrations in the primary coolant. The estimated number of defected fuel pins in the third and sixth cycles appeared to be $9.34{\pm}1.13\;and\;0.294{\pm}0.092$, respectively.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.11
• /
• pp.11-20
• /
• 1998

Testability analysis computes controllabilities and observabilities of all lines of a circuit and then evaluates fault coverage. The values of controllability and observability as well as fault coverage produced by testability analysis are used for applications of testability analysis. ITEM was evaluated as a fault coverage tool. But the values of controllability and observability at all lines of circuits must be estimated as a performance measure of testability tools for another application such as partial scan. In this paper, partial scan method based on sensitivity analysis which estimates relative improvement of detectability of circuits after scanning a flip-flop is used for performance evaluation of ITEM. Performance of ITEM, with respect to testability values on each net, has been measured by comparing ITEM and STAFAN. Partial scan performance achieved by ITEM is very similar to that of STAFAN, but ITEM takes less CPU time. Therefore ITEM is very efficient for partial scan application because ITEM runs faster for very large circuits in which execution time is critical.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.10a
• /
• pp.144-145
• /
• 2003

감자는 전세계 대부분의 국가에서 재배되고 있는 세계 4대 주곡 작물인 동시에 스낵류 시장에서도 중요한 부분을 차지하고 있다. 우리나라의 감자 가공산업은 1990년대 초부터 활기를 띠기 시작여하 현재 2,000억불의 매출을 달성하고 있다. 이중 우리나라 농민이 직접 생산한 감자를 원료로 사용하는 천연칩 감자 가공산업은 매출액을 기준으로 144억 (1997년)에서 700억 (2001년)으로 과거 10년 동안 괄목할 만한 성장을 하였다. 우리나라의 연간 감자 칩 원료용 가공용 감자 소요량은 총 51,600톤 (2002 년)으로 그중 40,600톤은 국내생산량으로 충당하고 나머지는 냉동감자를 수입하여 처리하고 있다. 가공원료용 감자는 괴경의 크기나 모양과 같은 외부품질과 환원당이나 고형분 함량과 같은 내부품질이 좋아야 한다. 하지만 가공용 감자의 내·외부품질이 좋게 판정되어도 내부갈색반점이나 중심공동과 같은 괴경 생리장해가 발생하면 원료용 감자로서의 상품 가치가 상실된다. 국내 칩 가공원료용 감자는 봄재배에서는 약 5 ∼ 7 ％, 여름재배에서는 10 ∼ 15 ％의 괴경 생리장해가 발생되고 있다. 현재 위와 같은 생리장해는 가공공장에서 감자를 잘라서 골라내거나 감자 칩을 만든 후 제거하는 방법을 쓰고 있다. 이에 감자를 수확 후 감자칩으로 가공하기 전에 생리장해가 발생한 감자를 제거하여 생산 공정에서의 불필요한 가공을 줄일 수 있는 방법이 개발되어야 할 필요성이 증대되고 있다. 최근, 농산물의 비파괴적 품질 평가와 선별에 있어서 가장 실용적이고 성공적인 기술 중의 하나는 농산물의 광학적 성질을 이용한 전기-광학 기술이다. 그중 X-선과 같이 파장이 짧은 방사 에너지는 대부분의 농산물을 투과하여 내부의 질량 밀도의 변화와 상관관계를 갖는 품질 인자를 비파괴적으로 평가하는데 적합하나 아직 국내에선 X-선을 이용한 가공용 감자의 내부 결함특성에 대한 연구는 이뤄지지 않고 있다. 이에 본 연구에서는 가공용 감자의 내부결함 특성중 하나인 내부동공의 X-선에 의한 특성을 본 연구소에 있는 X-선 발생장비로 측정해 보고 비파괴적인 방법으로 실시간 가능성을 시험하였다. 감자는 수원 농산물 도매시장에서 2003년산 가공용 감자 (품종:선농)를 구매하여 사용하였다. 감자내 내부동공은 35 ∼ 40 kV와 5.25 mA값으로 발생된 X-선에 의해 잘 검출되는 것으로 나타나, 현장에서 충분히 활용가능 할 것으로 판단되었다. 금후, 실시간으로 내부동공을 검출할 수 있는 시스템을 개발할 계획이다.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.207-214
• /
• 2005

The reflected signals from the defects of a pile and the boundaries between the pile and soils are analyzed to evaluate the integrity of drilled shafts in the impact-echo test. Signals varied according to both of the stiffness ratio of the pile to defects and that of the pile to surrounding soils. Model tests using the small size pile in the laboratory and numerical analyses have limitations in finding the characteristics of the signals due to different stress wave characteristics and unreliable modelling for the interaction between the pile and soils respectively. Full scale testing piles which have artificial defects are installed by the actual construction method and they were used to investigate the characteristics of reflected signals according to defects and the stiffness ratios of the pile to soils around.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.216-216
• /
• 2015

용융아연 도금 공정에서 강판이 도금욕에 침적되는 동안 강판으로부터 용출되는 Fe는 도금욕 내 Al, Zn와 반응하여 다양한 형태의 드로스를 형성시키는 원인이 된다. 이들 드로스는 강판 표면에 다양한 형태의 결함을 야기하므로, 실제 도금 공정에서 도금욕 내 발생하는 드로스의 생성거동에 관한 이해는 필수적이다. 따라서 본 연구에서는 도금욕 내 $Fe_xAl_yZn_z$계 드로스 생성에 미치는 도금욕 내 Al 및 Fe 함량의 영향에 대해 고찰하였으며, in-situ sampling 기법 및 finger rotating method를 이용하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.3
• /
• pp.396-400
• /
• 1998

The physical properties of KLN single crystals very significantly according to the $Nb_2O_5$ content in grown crystal, therefore, it is very important to control the composition of KLN single crystals. In this study, KLN single crystals of high content $Nb_2O_5$ were grown by temperature fluctuation and TSSG (Top-seeded solution growth) methods with increasing the $Nb_2O_5$ content of starting solution. To investigate the existence of defect due to the increase of $Nb_2O_5$ content, dielectric and optical properties were measured. Due to the increase of defects in grown KLN single crystal, the shift of cutoff-frequency to lower energy and a broad Curie range, which shows the DPT (diffuse phase transition) characteristics, were observed.