• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.2
• /
• pp.156-163
• /
• 2001

The experiment is conducted on the rapidly rotating incompressible flow within a confined cylinder using LDV(Laser Doppler Velocimetry). The configurations of interest are the flows between a rotating upper disk with a bar and a stationary lower disk enclosed within a cylinder. The flow is considered to be an axisymmetric undisturbed basic flow. The results show that the flow is strongly dependent on the radius and the shape of bar but is negligibly affected by the Reynolds number in turbulent flow. It is observed that in the lid-driven case the main forms near the wall as the Reynolds number increases. The thin bar causes the second axial flow due to the suction effect and the thick bar causes the main flow to be pulled toward the surface of the bar. The step bar shows the dual effect of the two. 1:2 tilt bar shows that the main flow distributes wider than the other cases in which interference occurs due step bar.

• Clean Technology
• /
• v.23 no.1
• /
• pp.42-53
• /
• 2017

Numerical analysis was done to evaluate the fluid distribution inside of the mixing quencher to increase the reaction efficiency of the aqueous hydrogen peroxide solution in the scrubbing column which is used for simultaneous desulfurization and denitrification. Effective injection of the aqueous hydrogen peroxide ($H_2O_2$) solution in the mixing quencher has major effects for improving the reaction efficiency in the scrubbing column by enhancing the mixing of the aqueous $H_2O_2$ solution with the exhaust gas. The current study is to optimize the array of nozzles and the spray angles of the aqueous $H_2O_2$ solution in the mixing quencher by using the computational method. Main concerns of the analysis are how to enhance the uniformity of the $H_2O_2$ concentration distribution in the internal flow. Numerical analysis was done to check the distribution of the internal flow in the mixing quencher in terms of RMS values of the $H_2O_2$ concentration at the end of quencher. The concentration distribution of $H_2O_2$ at the end of is evaluated with respect to the different array of the nozzle pipes and the nozzle tip angles, and we also analyzed the turbulence formation and fluid mixing in the zone. The effect of the spray angle was evaluated with respect to the mixing efficiency in different flow directions. The optimized mixing quencher had the nozzle array at location of 0.3 m from the inlet duct surface and the spray angle is $15^{\circ}$ with the co-current flow. The RMS value of the $H_2O_2$ concentration at the end of the mixing quencher was 12.4%.

• Proceedings of KOSOMES biannual meeting
• /
• 2005.11a
• /
• pp.159-163
• /
• 2005

This experimental study was performed to investigate internal flow and unsteady flow characteristics using a model for actual shape of a plate heat exchanger and visualization of flow through the particle image velocimetry. Seven Reynolds numbers were selected by calculation with the height of grooved channel and sectional mean velocity of inlet flow in the experiment, and instantaneous velocity distributions and flow characteristics were experimently investigated. The triangular grooved channel had a compound flow consisting of the flow in lower channel and the groove flow receiving shear stress by the channel flow in the experiment. The sheared mixing layer, in the boundary between the triangular groove and the channel, affected main flow to raise turbulent in the channel.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.5
• /
• pp.442-449
• /
• 1984

Turbulent jet flow has been studied in many ways; a plane jet, a rectangular jet, an annular jet, a round jet, a wall jet, a parallel jet, a valve jet, a cross jet, a slit jet and etc. In this report, a 45.deg. cross jet flow was tried by using two same dimensioned nozzels(dia..phi.20)which were set up at the exit of the subsonic wind tunnel. Each jet flows to the direction of 22.5.deg. to the axis of downstream of the mixed flow. The centerline of each jet meets at the distance of 217.3mm and their mixing flow could be imagined to develop beyond that distance, so the measurement was effectuated at X/X$_{0}$=1.2-1.5. The section of the mixed flow a elliptic circle which is formed by the 22.5.deg. inclined flows to the X direction. This experimental study aimed at the investigation of the turbulent mixing process of two jets; the mean velocities, the turbulent shear stresses, the correlation coefficients, and the momentum were respectively measured. The mean velocity distribution profiles of the down-stream component measured in the Y direction coincide well with the empirical equation of Gortler and those measured in the Z direction agree with the equation of H. Schlichting. Other mean velocities V over bar and W over bar components were randomly distributed. The higher values with same order of the intensity of turbulence were largely distributed at the central part of the flow. The momentum was decreased up to 70% by the shock losses and the development of intense turbulences, but it kept its value constantly beyond X/d=14. Two-channel hot-wire anemometer systems (model 1050 series), X-type hot-wire made of tungsten (dia. .phi.e.mu.m, long 3mm, model 0252 T5), a computer(model HP 9845B0, and a plotter (model HP 9872C) were used for the experiments and the analyses.s.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.105-105
• /
• 2019

보나 여수로와 같은 수공구조물의 주변에서 발생하는 흐름 거동은 구조물 모서리에서 발생하는 흐름분리(flow separation)와 이에 따른 전단층(shear layer)과 재순환(recirculation) 흐름 영역의 발달 그리고 분리된 흐름의 재부착(reattachment)이 특징이다. 공학적으로 난류의 해석에 있어서 이러한 흐름 거동들을 정확하게 예측하는 것은 수공구조물 설계에 있어서 중요하다. 이 연구에서는 흐름 분리와 재순환 영역의 발달 그리고 흐름 재부착을 포함하는 후방계단(backward-facing step) 흐름을 155,000의 레이놀즈수 조건에서 하이브리드 RANS/LES 모델을 적용하여 해석결과를 평가한다. 하이브리드 모델로는 벽에 인접한 격자의 해상도에 상대적으로 민감하지 않은 SST(shear-stress transport) 난류 모델을 이용하는 DES(detached-eddy simulation) 기법을 적용하였다. 계단 높이가 h인 계산영역은 흐름방향 길이가 34h, 높이는 계단 상류와 하류에서 각각 1h와 2h 그리고 폭은 $2{\pi}$이다. 계단은 상류단으로부터 10h 하류부 지점에 위치한다. 경계조건으로 상부와 하부 벽면에 대해서는 비활조건을 적용한다. 상류부 수로에서 완전 발달한 흐름을 재현하기 위해서 유입경계조건은 유입부 하류 $2{\pi}h$ 지점에서 계산된 유속과 난류량을 매핑(mapping)기법을 이용하여 반복적으로 적용한다. 총 3.1백만개와 7.3백만개의 셀로 계산영역을 구현한 두 개의 계산격자 그리고 약 3.1백만개의 셀을 이용했지만 벽면 근처에서의 격자 구성을 다른 방식으로 설정한 두 가지 격자를 이용하여 격자 해상도가 DES 수치해석 결과에 미치는 영향을 분석하였다. 수치해석결과는 본 연구에서 상류단 조건으로 적용한 매핑기법이 대상 수로에서 완전 발달한 흐름을 잘 재현함을 보여주며, 합리적인 DES 해석 결과를 얻기 위해서는 벽에 수직한 방향으로 적절한 격자의 해상도와 분포가 필요함을 보여준다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.4
• /
• pp.67-74
• /
• 1999

Problems created by supersonic jet impinging on solid objects or ground arise in a variety of situations. For example multi-stage rocket separation, deep-space docking, V/STOL aircraft, jet-engine exhaust, gas-turbine blade, terrestrial rocket launch, and so on. These impinging jet flows generally contain a complex structures. (mixed subsonic and supersonic regions, interacting shocks and expansion waves, regions of turbulent shear layer) This paper describes experimental works on the phenomena (surface pressure distribution, flow visualization) when underexpanded supersonic jets impinge on the perpendicular, inclined plate using a supersonic cold-(low system. The used supersonic nozzle is convergent-divergent type, exit Mach number 2, The maximum on the plate when it was inclined was much larger than perpendicular plate, owing to high pressure recoveries through multiple shocks. Surface pressure distribution as to underexpanded ratio showed similar patterns together.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1417-1426
• /
• 2001

Turbulent flow characteristics in the near wake of a square cylinder have been studied experimentally by using a Digital PIV method. Experiments are performed at the Reynolds numbers of 1600 and 3900 based on the free-stream velocity and the square height. The ensemble averaged turbulence statistics are acquired from 2030 realizations of instantaneous fluctuating velocity field after the conventional Reynolds decomposition. The differences in turbulent intensity and Reynolds shear stress profiles fur both oases indicate that the effect of Reynolds number seems to be descernible mainly due to the occurrence of transition in the separated shear layer. Because of the periodic nature of vortex shedding process, transverse velocity fluctuations contribute dominantly , to turbulent kinetic energy distribution. A comparison with previous LDV data obtained at much higher Reynolds number shows a fairly good agreement each other. It turns out that the effect of Reynolds number diminishes as increasing Reynolds number, which is a well-known feature of a sharp-edged bluff body wake. The streamwise variation of turbulence intensities are compared with those from a circular cylinder along the centerline at the same Reynolds number. The overall magnitudes and the decay rates of turbulence intensities are quite similar, but some differences are noticeble especially in the transverse intensity variation.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.91-91
• /
• 2022

하천 합류부에서 수체의 흐름은 매우 역동적으로 변화하며 합류부의 복잡한 3차원 흐름과 난류 구조는 2차류(secondary currents)의 강도변화, 전단층(shear layer)의 뒤틀림 그리고 재순환구역(recirculation zone)의 발생 등 합류부에서의 독특한 특징을 형성한다. 이러한 특징들의 변화는 수체의 흐름구조 뿐만 아니라 하천으로 유입된 오염물의 거동에도 영향을 준다. 기존의 합류부 연구들은 주로 본류와 지류의 합류각이나 유량비에 차이를 두어 합류부의 특징 변화를 모의하였다. 하지만 실제 자연하천에서 홍수방지를 위한 수심확보, 건축자재의 골재수집 등 다양한 목적으로 수행되는 본류의 준설작업으로 인해 발생하는 본류와 지류의 하상면 단차 또한 합류부의 특성에 영향을 미치는 주요한 인자 중 하나이다. 단차가 커짐에 따라 증가하는 지류수체의 낙차는 이차류의 강화를 야기하며 이는 합류부에서의 유속구조를 변화시켜 흐름을 가속시키거나 지체시키며 오염물의 혼합에 영향을 미친다. 본 연구에서는 3차원 수치모의를 통해 90도로 합류되는 수로에서의 흐름구조와 오염물의 혼합에 단차비와 유량비가 미치는 영향을 모의하였다. 유동장 해석을 위해 3차원 RANS (Reynolds-averaged Navier-Stoke) 방정식을 사용하였으며 난류해석은 k-𝜔 SST 모델을 이용하였다. 본류의 경우 11.4m의 수로 연장을 갖고, 하폭은 0.3m이며 수심은 단차의 크기에 따라 변화한다. 지류의 경우는 수로연장 1m, 하폭 및 수로깊이는 0.1m이다. 수치결과의 검증을 위해 이주하(2013)이 수행한 실내 합류수로의 실험결과를 이용하였다. 모의결과를 통해 파악한 합류부의 흐름특성을 이용하여 적절한 2차원 분산계수를 산정한다. 자연하천에서 오염물의 혼합거동을 효과적으로 모의하기 위해 수심 평균된 2차원 이송-분산모형을 이용하는데 이때 적절한 분산계수의 산정이 필수적이다. 본 연구에서는 합류 후 흐름방향에 따라 분산특성이 상이한 구간을 구분하여 분산계수를 산정하였으며 이를 통해 오염물의 거동을 정확하게 모의하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.1-8
• /
• 2002

The flow and combustion patterns have been investigated inside the gasoline engine cylinder with the swirl or tumble flow, whereas the air flow characteristics, which are generated in the part of intake system before entering into the intake manifold, have not been known completely. It is necessary to analyze the flow field in the intake system consisting of air rater, throttle valve and intake manifold. The throttle valve, used to control the intake air flow rate, is important because it makes various mass flow rate and flow patterns. Three-dimen-sional How characteristics such as velocities, turbulent intensities and Reynolds shear stresses are measured by the hot wire anemometer at the exit of the throttle valve with the variation in the valve opening angle($15^{\circ}$, $45^{\circ}$, $75^{\circ}$ and $90^{\circ}$) and the Reynolds numbers (45000, 70000 and 140000). There are a lot of changes in flow characteristics at $75^{\circ}$ due to the large recirculation flow comparing with those of the other cases, and the streamwise velocity is especially enforced strongly below the valve shaft. The other component velocities are relatively large near the centerline parallel to the valve shaft. The effects of the Reynolds number on the flow field are not severe.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.6
• /
• pp.16-22
• /
• 2004

Unsteady vortex shedding behind a rectangular cylinder near a wall influences both increasing of drag and dynamic stability of heavy vehicle, bridge or building. Incompressible Averaged Navier-Stokes equation with modified ${\varepsilon}-SST$ turbulence model is adapted for investigating the flow field between the rectangular cylinder and the wall. In case the vortex shedding happens, not only the averaged maximum velocity is higher than other cases, but the position of the maximum velocity is closer to the lower surface of rectangular cylinder. On this study, it is confirmed that the vortex shedding behind a rectangular cylinder can be suppressed by the passive control method added by horizontal and vertical fences to the lower surface of rectangular cylinder.