• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.298-304
• /
• 1995

유동이 있는 경우 발생하는 소음에 대한 실험적 연구는 풍동과 무향실이 결합된 음향풍동에서 수행될 수 있다. 이러한 음향풍동은 팬, 수축부, 수집부, 확산부 그리고 무향실에 주의해서 설계되어야 하고 특히 각 부분에서 발생할 수 있는 이차소음을 최소화하도록 설계되어야 한다. 최종적으로 소음기와 흡음재를 이용해서 팬소음과 이차소음의 전파를 줄인다. 본 음향풍동은 개방형 흡입식(open suction type)으로 시험부에서 유속 62.8m/s, 난류강도 0.1%이하, 배경소음 50-55dB 이하로 설계되었다. 이러한 조건을 만족시키기 위하여 하니콤과 6장의 스크린이 있는 정체실과, 21:1의 수축비를 갖는 수축부를 이용하여 난류강도를 낮추고, 흡음재와 90도 각도의 모서리 그리고 공명형과 소산형 소음기로 소음의 전파를 줄였다.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.430-435
• /
• 2008

Total lengths of domestic pipe network for district heating system are above about 2,500Km. A lots of pumping power for heat transportation through long pipe are required by the flow friction of pipe surface. Until now there have been considered about various methods to reduce the flow friction for district heating system such as using surfactants and turbulence promoters by swirl flow and baffles etc. At this study, swirl flow generator was tested about the possibility to increase the heat transfer ratio at the heat exchanger in the case which the suppling water temperature increased from $50^{\circ}C$ until $120^{\circ}C$. Experimental results showed that the heat transfer ratio increased and also pressure increase ratio increased simultaneously in the case which swirl flow generator installed. The amount of the increasing ratio for heat transfer and pressure were reached until 4.33% and 11% at the case of $120^{\circ}C$ suppling temperature which domestic district heating system were using.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.639-647
• /
• 2019

Recently, as the semiconductor integration technology due to miniaturization and high density of electronic equipment have developed, it is importantly recognized the application of thermal control system in order to release inner heat generated from chips, modules, In this study, we considered the heat transfer and pressure drop characteristics in a horizontal channel with four blocks using k-${\omega}$ SST turbulence model During CFD (Computational Fluid Dynamics) analysis, the parameters applied block width, block height, heat source and turbulence generator placement etc. As the boundary conditions of analysis, the channel inlet temperature and flow velocity were respectively 300 K and 3.84 m/s, the heat flux was $358W/m^2$. As a result, the heat transfer performance was decreased as the block width ratio (w/h) was increased, while it was increased as the block height ratio (h/w) was increased. In addition, as the arrangement of heat source size was increased to high heat flux from low heat flux, it was influenced by heat source size and the heat transfer coefficient showed a tendency to increase, When the turbulence generator was installed in the upper part of block No. 1 position the closely to the channel entrance, the heat transfer characteristics was greatly influenced on the whole of four heating blocks. and in oder to consider the pressure drop characteristics, we are able to select the most appropriate turbulence generator's position.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.545-550
• /
• 2017

When the systolic blood pressure is high, intermittent turbulence in blood flow appears in the aorta and carotid artery with stenosis during the systolic period. The turbulent blood flow is difficult to analyze using the Newtonian turbulence model due to the viscous characteristics of blood flow. As the shear rate is increased, the blood viscosity decreases by the viscoelastic properties of blood and a drag reduction phenomenon occurs in turbulent blood flow. Therefore, a new non-Newtonian turbulent model is required for viscoelastic fluid and hemodynamics. The main aims of this study were to develop a non-Newtonian turbulence model using the drag reduction phenomenon based on the standard $k-{\varepsilon}$ turbulent model for a general non-Newtonian fluid. This was validated with the experimental data and has a good tendency for non-Newtonian turbulent flow. In addition, the computation time and resources were lower than those of the low Reynolds number turbulent model. A modified turbulent model was used to analyze various turbulent blood flows.

• Journal of Energy Engineering
• /
• v.10 no.3
• /
• pp.223-232
• /
• 2001

To study the stabilization characteristics of diffusion flame formed in the wake of a cylindrical bluff body with fuel injection, the flame stability limits, length and temperature of recirculation zone of flame, turbulence intensity distribution near the recirculation zone of flame were measured and analyzed. The length of recirculation zone is independent on main fuel injection quantity, but it is dependent on fuel injection angles, air stream velocity, and auxiliary fuel injection into recirculation zone. For diffusion flame, in general, the flame stabilization is deteriorated with increase of he length of recirculation zone, but if the turbulence generator is installed, the flame stabilization is improved with increase of the length of recirculation zone. The temperature of recirculation zone is dependent on fuel injection angles, auxiliary fuel injection into recirculation zone, turbulence generators, and it dependent on fuel injection angles, auxiliary fuel injection into recirculation zone, turbulence generators, and it has a maximum value at the condition of each theoretical mixture. In general, the more temperature of recirculation zone is low, the more flame is stable. But when the turbulence generator is installed, the more temperature of recirculation zone is low, the more flame is unstable. The turbulence intensity in the wake of bluff body is increased with increase of diameter or blockage ratio of grid. The more turbulence intensity is increased by installation of turbulence generator, the more flame is unstable. Finally, It is clear that the stabilization characteristics of diffuser flame can be controlled by some parameters such as fuel injection angles, auxiliary fuel injection into recirculation zone, turbulence generators.

• Proceedings of the Korean Society of Fisheries Technology Conference
• /
• 2001.10a
• /
• pp.75-76
• /
• 2001

산업적으로 강제 Swirl 유동은 난류를 촉진하기 위하여 많이 이용된다. 특히 Swirl유동은 난류 강도를 증가시켜 물질과 열의 전달 효과를 증진시켜 터빈 연소기, 열교환기 및 각종 산업용 버너 등의 공업분야에 폭넓게 이용되고 있다. Swirl강제 유동 발생 방법은 원추형 덕트방식, 베인형, 프로펠러형 등이 많이 이용되고 있으나 대부분의 방법은 강제로 와류(Swirl)를 발생, 촉진 및 증가 시키므로 유동손실 및 압력 손실 등을 수반하게 되어 많은 에너지 손실을 가져온다. (중략)

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1400-1405
• /
• 2001

In this study, an analysis program to assess the susceptibility of steam generator tubes due to the flow-induced vibration was developed. Analysis of fluid-elastic instability and random turbulence excitation for the U-tube bundle in CE-type steam generator was accomplished. The effective mass distribution along the U-tube was obtained to calculate the natural frequency and dynamic mode shape. Finally, stability ratios and rms vibration amplitude for selected tubes are obtained.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.2
• /
• pp.92-97
• /
• 2005

A series of combustion test was done to verify the optimization result of a gas generator for a 10 ton thrust liquid rocket engine. An injector element is F-O-F impinging type injector and the test was conducted with kerosene/LOX propellants. Test results of combustion temperature and pressure show a very good agreement with optimal design result and verify that the design method was properly established. And turbulence ring revealed its effectiveness in enhancing combustion gas mixing and temperature difference in the radial direction showed only less than 15K. Also turbulence ring induced only 3.2% pressure loss in the combustion chamber, which is far less than conventional level observed in a gas turbine engine. Axial temperature distribution also shows that turbulence ring could effectively reduce about 10% or more in gas generator length if its location is properly selected.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.315-320
• /
• 2008

This experimental study has been conducted to investigate the effect of the flame holder on the multi-slot film cooling in the ramjet combustor. The turbulent wake which is generated by the flame holder on the entrance of the coolant flow path affects on the slot. Adiabatic film cooling effectiveness on the downstream wall of the slot exit are measured. The results show that the film cooling performance is rapidly decreased after the slot exit by shear layer and high turbulence intensity between separated flows and coolant flows.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1254-1257
• /
• 2007

본 연구에서는 유류-유사 분리기내에서 유체의 흐름거동을 상용 3차원 수치모형인 FLOW-3D를 이용하여 해석하였다. 유류-유사 분리기는 도심지의 우수로 인한 유출발생시 동반되는 이물질을 여과시키는 기능을 가진 지하구조물이다. 우수로 인한 유출이 발생하여 유류-유사 분리기내로 흘러들어오는 유입수는 3차원적 거동을 하고 다양한 흐름특성을 갖는다. 따라서, 분리기내에서의 흐름거동을 정확히 해석하는데 많은 어려움이 있다. 본 연구에서는 정류판(baffle)과 유류흡착기(oil skimmer)로 구성된 유류-유사 분리기에서의 유류와 유사를 포함하고 있는 유출수의 복잡한 거동을 해석하기 위해 수치모의를 실시하였다. 유류와 유사에 대한 포착률(oil and grit trap)은 유류-유사 분리기내에서 유체의 흐름거동과 관계된다. 따라서, 본 연구에서는 유류와 유사의 포착률을 향상시키기 위한 수치모의의 기초적인 단계로서 유류-유사 분리기내에서 유류흡착기(oil skimmer)를 설치한 경우와 설치하지 않은 경우에 대한 유체의 흐름거동을 FLOW-3D를 이용하여 3차원 수치모의를 실시하였다. 수치모의를 통해 유류흡착기의 유무에 따른 유류-유사 분리기내에서의 흐름거동을 알 수 있었으며, 유류흡착기를 설치한 경우엔 유류 흡착기에 의해 여과될 수 있는 유류와 유사에 대한 각각의 포획률이 높아짐을 알 수 있었다.