• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.11
• /
• pp.1-8
• /
• 2011

One of the most important parameters that limit maximum output power of transistor is breakdown. InAlAs/InGaAs/GaAs Metamorphic HEMTs (MHEMTs) have some advantages, especially for cost, compared with InP-based ones. However, GaAs-based MHEMTs and InP-based HEMTs are limited by lower breakdown voltage for output power even though they have good microwave and millimeter-wave frequency performance with lower minimum noise figure. In this paper, InAlAs/$In_xGa_{1-x}As$/GaAs MHEMTs are simulated and analyzed for breakdown. The parameters affecting breakdown are investigated in the fabricated 0.1-${\mu}m$ ${\Gamma}$-gate MHEMT device having the modulation-doped $In_{0.52}Al_{0.48}As/In_{0.53}Ga_{0.47}As$ heterostructure on the GaAs wafer using the hydrodynamic transport model of a 2D commercial device simulator. The impact ionization and gate field effect in the fabricated device including deep-level traps are analyzed for breakdown. In addition, Indium mole-fraction-dependent impact ionization rates are proposed empirically for $In_{0.52}Al_{0.48}As/In_xGa_{1-x}As$/GaAs MHEMTs.

• Journal of Sensor Science and Technology
• /
• v.10 no.5
• /
• pp.292-303
• /
• 2001

This work reports the tunneling effects of the lateral field emitters. Tunneling effect is applicable to the VMFS(vacuum magnetic field sensors). VMFS uses the fact that the trajectory of the emitted electrons are curved by the magnetic field due to Lorentz force. Polysilicon was used as field emitters and anode materials. Thickness of the emitter and the anode were $2\;{\mu}m$, respectively. PSG(phospho-silicate-glass) was used as a sacrificial layer and it was etched by HF at a releasing step. Cantilevers were doped with $POCl_3(10^{20}cm^{-3})$. $2{\mu}m$-thick cantilevers were fabricated onto PSG($2{\mu}m$-thick). Sublimation drying method was used at releasing step to avoid stiction. Then, device was vacuum sealed. Device was fixed to a sodalime-glass #1 with silver paste and it was wire bonded. Glass #1 has a predefined hole and a sputtered silicon-film at backside. The front-side of the device was sealed with sodalime-glass #2 using the glass frit. After getter insertion via the hole, backside of the glass #1 was bonded electrostatically with the sodalime-glass #3 at $10^{-6}\;torr$. After sealing, getter was activated. Sealing was successful to operate the tunneling device. The packaged VMFS showed very small reduced emission current compared with the chamber test prior to sealing. The emission currents were changed when the magnetic field was induced. The sensitivity of the device was about 3%/T at about 1 Tesla magnetic field.

• Journal of the Korean Magnetics Society
• /
• v.18 no.4
• /
• pp.147-153
• /
• 2008

It has been well-known that the Fe/GaAs heterostructure has a small lattice mismatch of 1.4% between Fe and GaAs, and the Fe layer is grown epitaxially on the the GaAs substrate. There are rich physics are observed in the GaAs/Fe interface, and the spininjection is actively studied due to its potential applications for spintronics devices. We fabricated Fe wedge layer in the thickness range $0{\sim}3.4$ nm on the GaAs(100) surface with 5-nm thick Au capping layer. The magnetic anisotropy of the Fe/GaAs system was investigated by employing Brillouin light scattering(BLS) measurements in this study. The spin wave excitation of Fe layer was studied as the function of intensity and the in-plane angle of external magnetic field, and thickness of Fe layer. Also these various dependences were analyzed with analytic expression of spin wave surface mode in order to determine the magnetic anisotropies. It has been found that the GaAs/Fe/Au system has additional uniaxial magnetic anisotropy, while the bulk Fe has biaxial anisotropy. The uniaxial anisotropy shows increasing dependency respected to decreasing thickness of Fe layer while biaxial anisotropy is reduced with Fe film thickness. This result allows the analysis that the uniaxial anisotropy is originated from interface between GaAs surface and Fe layer.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.1
• /
• pp.51-58
• /
• 1999

The effects of glass composition on the wettability and reactivity with $ZrO_2$substrate was evaluated and fabrication variables and glass compositions was investigated. Various glass compositions was investigated. Alkaline earth silicate glass show good wettability and lower viscosity and crystallization of glass could be prevented by $B_2O_3$.The sealant glass begin to wet on $ZrO_2$substrate below $900^{\circ}C$ and porosity occurred in various glass compositions, the crystallization and porosity in the glass could be prevented by the addition of flux into glass composition. But flowability and reactivity of glass with $ZrO_2$substrate was enhanced. Processing variables should be optimized to reduce the porosity by enhancing the sintering of glass powder. Many silicate glasses were investigated for the applications of high temperature sealants. Wetting and bonding of glass was good enough to seal together between $ZrO_2$and other ceramic components of SOFC. But porosity and reaction layer were occurred in the sealant glass. It will be possible to produce glass sealant without porosity and reaction layer at the interface by optimization of processing variable and modify the glass compositions. In present study, wettability of glass-filler composite was investigated. The porosity, shape of filler and interfacial reactions of sealant glass with fillers were examined.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.416-417
• /
• 2013

최근 질화물계 발광다이오드(light emitting diode, LED) 소자는 핸드폰, 스마트 TV 등의 디스플레이 분야와 실내외조명, 감성조명, 특수조명 등의 조명분야에 그 응용분야가 급속히 확대되고 있다. 이러한 LED 소자는 에너지 절감과 친환경에 장점을 가지고, 가까운 미래에 조명시장을 대체할 것으로 예상된다. 이를 만족하기 위해서는 현재보다 더 높은 효율을 갖는 LED 개발이 요구되어지고 있는 상황이다. 일반적으로 질화물계 LED 소자의 효율은 내부양자 효율, 광추출 효율 등으로 나타낼 수 있다. 내부 양자효율은 성장된 결정의 질의 개선 및 다층의 이종접합 또는 다중양자우물 구조와 같이 활성층의 캐리어 농도를 높이는 접합구조로 설계되어 80% 이상의 효율을 나타낸다. 그러나 광추출 효율은 이에 미치지 못하고 있다. 이는 반도체 재료의 높은 굴절률로 인하여 빛이 외부로 탈출하지 못하고 내부로 반사되거나 물질 안에서 흡수가 일어나기 때문이다. 따라서 이러한 문제를 해결하기 위해 많은 연구 그룹들은, 표면에 패턴 형성하여 빛의 전반사를 줄여 그 효율을 올리는 연구결과를 보고하고 있다. 대표적인 방법으로는 wet etching, 전자빔 리소그라피, 나노임프린트 리소그라피, 레이저 홀로 리그라피, 나노스피어 리소그라피 등이 사용되고 있다. 이 중, 나노스피어 리소그라피는 폴리스틸렌 혹은 실리카 등과 같은 나노 크기의 bead를 사용하여 반도체 기판 표면에 단일층으로 고르게 코팅한 마스크로 사용하여 패턴을 주는 방법이다. 이 방법의 장점으로는 대면적에 균일한 패턴을 형성할 수 있고, 공정비용이 저렴하여 양산하기에 적합하다는 특징이 있다. 나노스피어 리소그라피를 통해서 표면에 생성된 패턴 모양의 각도에 따라서, 식각되는 깊이에 변화에 따라 실험한 결과들은 있지만, 아직까지 크기가 다른 나노입자들의 마스크 이용하여 형성된 패턴 밀도에 따른 광 추출 효과에 대한 연구가 많이 미흡하다. 따라서 본 연구에서는 다양한 크기의 실리카로 패턴을 형성시켜 패턴 밀도에 대한 광추출 효율의 효과에 대해서 조사하였다. 실험 방법으론, DI, 에탄올, TEOS, 암모니아의 순서대로 그 혼합 비율을 조정하여 100, 250, 500 nm 크기의 나노입자를 합성하였고 이것을 질화물계 LED의 표면 위에 단일층으로 스핀코팅 방법을 통해 코팅을 하였다. 그 후 ICP-RIE 방법으로 필라 패턴을 형성하였는데, 그 결과 100 nm SiO2 입자를 이용한 경우 $4.5{\times}10^9$/$cm^2$, 250 nm의 경우 $1.4{\times}10^9$/$cm^2$, 500 nm의 경우 $0.4{\times}10^9$/$cm^2$의 패턴의 밀도를 보여주었다(Fig. 1). 패턴의 밀도에 따라 전계광학적 특성을 확인하여 보았는데, 그 결과는 평평한 표면과 비교하였을 때 100 nm에서 383%, 250 nm에서는 320%, 500 nm에서는 244% 상승하는 결과를 보여주었다(Fig. 2). 이번 실험을 통해서 LED의 광추출 효율은 표면 모양과 깊이 뿐 아니라 밀도가 커질수록 그 효율이 올라간다는 사실을 알 수 있었다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.2
• /
• pp.5-12
• /
• 2000

Uncooled metallic thin-film thermopile infrared detectors have been fabricated, and the figures of merit for the detectors were examined. The hot junctions of a thermopile were prepared on a $Si_{3}N_{4}/SiO_{2}/Si_{3}N_{4}$-membrane which acts as a thermal isolation layer, the cold junctions on the membrane supported with the silicon rim which functions as a heat sink, and Au-black was used as an infrared absorber. Infrared absorbance of Au-black, which strongly depends on the chamber pressure during Au-evaporation and its mass per area, was found to be about 90 ％ in the wavelength range from 3${\mu}{\textrm}{m}$ to 14${\mu}{\textrm}{m}$. Voltage responsivity, noise equivalent power, and specific detectivity of Bi-Sb thermopile infrared detector at 5 Hz-chopping frequency were about 10.5V/W, 2.3 nW/Hz$^{1/2}$, 및 $1.9\times10^{7}$ cm.Hz$^{1/2}$/w at room temperature in air, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.4
• /
• pp.11-15
• /
• 2001

In this paper, hermetic sealing technology was studied for wafer level packaging of the RF-MEMS devices. With the flip-chip bonding method. this non-conductive B-stage epoxy sealing will be profit to the MEMS device sealing. It will be particularly profit to the RF-MEMS device sealing. B-stage epoxy can be cured by 2-step and hermetic sealing can be obtained. After defining 500 $\mu\textrm{m}$-width seal-lines on the glass cap substrate by screen printing, it was pre-baked at $90^{\circ}C$ for about 30 minutes. It was, then, aligned and bonded with device substrate followed by post-baked at $175^{\circ}C$ for about 30 minutes. By using this 2-step baking characteristic, the width and the height of the seal-line could be maintained during the sealing process. The height of the seal-line was controlled within $\pm$0.6 $\mu\textrm{m}$ in the 4 inches wafer and the bonding strength was measured to about 20MPa by pull test. The leak rate, that is sealing characteristic of the B-stage epoxy, was about $10^{-7}$ cc/sec from the leak test.

• Journal of the Korean Magnetics Society
• /
• v.10 no.4
• /
• pp.159-163
• /
• 2000

MR characteristics in magnetic tunnel junction using CoO as the oxide barrier were investigated. Spin-dependent tunnel junctions were fabricated on 4$\^$o/ tilt-cut (111)Si substrates in 3-gun magnetron sputtering system. The top and bottom ferromagnetic electrodes were Ni$\_$80/Fe$\_$20/(300 $\AA$) and Co(300 $\AA$), respectively. The oxide barriers (CoO) were formed by the thermal oxidation at room temperature in an O$_2$ atmosphere and the plasma oxidation. The increase of coercive field due to antiferromagnetic-ferromagnetic coupling has been observed in O$_2$plasma-oxidized CoO based junctions at room temperature. At a sensing current of 1 mA, MR ratios of O$_2$plasma-oxidized CoO based junction and thermal-oxidized CoO based junction at room temperature were 1% and 5%, respectively. Larger MR ratios are observed in magnetic tunnel juctions with thermal oxidized CoO when sensing current more than applied 1.5 mA. At a sensing current of 1.5 mA, we have observed MR value of 28 % and specific resistance (RA=R$\times$A) value of 10.9 ㏀$\times$㎛$^2$. When specific resistance values reached 2.28 ㏀$\times$㎛$^2$, we have observed that MR ratios become as high as 120%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.640-644
• /
• 2000

The microstructure, wettability, shear strength and aging effect of Sn-3.5Ag/Cu and Alloy42 lead-frame solder joints were measured for comparison. In the case of Sn-3.5Ag/Cu, Ag$_3$Sn and Cu$\sub$6/Sn$\sub$5/ phases in the matrix Sn and 1∼2$\mu\textrm{m}$ thick Cu$\sub$6/Sn$\sub$5/ Phase at the interface of solder/lead-frame were formed. In the case of Sn-3.5AAg/A11oy42, only Ag$_3$Sn Phase of low density in the matrix Sn and 0.5∼1.5$\mu\textrm{m}$ thick FeSn$_2$phase at the interface of solder/lead-frame were formed. Comparing to Cu, Alloy42 shear strength of Alloy 42 solder joints was smaller than that of Cu and all declined after aging. After aging at 180$^{\circ}C$ for 1 week, η-Cu$\sub$6/Sn$\sub$5/ layer was formed on Cu lead-frame, while AgSn$_3$ phase in the matrix and thickened FeSn$_2$at the interface were formed on Alloy42 lead-frame.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.2
• /
• pp.17-28
• /
• 2012

It is known that thermo-mechanical properties of solder material and molding compound in WB-PBGA packages are considerably affected by not only temperature but elapsed time. In this paper, finite element analysis (FEA) taking material nonlinearity into account was performed for more reliable prediction on deformation behavior of a lead-free WB-PBGA package, and the results were compared with experimental results from moire interferometry. Prior to FEA on the WB-PBGA package, it was carried out for two material layers consisting of molding compound and substrate in terms of temperature and time-dependent viscoelastic effects of molding compound. Reliable deformation analysis for temperature change was then accomplished using viscoplastic properties for solder ball and viscoelastic properties for molding compound, and the analysis was also verified with experimental results. The result showed that the deformation of WB-PBGA packages was strongly dependent on material model of molding compound; thus, temperature and time-dependent viscoelastic behavior must be considered for the molding compound analysis. In addition, viscoelastic properties of B-type molding compound having comparatively high glass transition temperature of $135^{\circ}C$ could be recommended for reliable prediction on deformation of SAC lead-free WB-PBGA packages.