• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.693-699
• /
• 2016

The simulators for pump operation developed by domestic or overseas research have been developed for dynamic analysis or operator training purposes. However, previous developed simulators focused on the operators so they are unsuitable for logic designers or commissioning engineers who need to change the operation conditions or logics arbitrarily. In addition, the simulator for two or more condensate pumps' operation, which can be used easily by plant designers or operators, has not been developed. Accordingly, this paper suggests a simulation method that can be used easily for plant designers or operators using MATLAB Simulink. This suggestion helps users who can use MATLAB to implement ANSI/ISA S5.2, which is applied mainly for DCS (Distributed Control System). In addition, to implement the logics specified in the CODE, Sub-Systems were created for the block and evaluated to determine if they can be used in the simulator. In the working level stage using the suggested method, all error possibilities that might occur during the three pumps' rotation operation could be verified with the suggested simulator during the design stage or before operation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.736-741
• /
• 2017

This paper examines the design for improving the wiper system of rotorcraft. During rotorcraft operation, the wiping performance and excessive clearance can decrease. The wiper system consists of a wiper arm assembly, motor, convertor and flex drive. If there is a problem with the wiper system, the operation ability decreases because the operation is restricted in a rainy environment. There are two main causes of the problem of the wiper system: the lifting forces acting on the wiper arm in aircraft flight and the excessive gap of the components. To remedy these two problems, the wiper arm was improved. The improvements included increased contact pressure on the wiper arm (spring tension), improved gear clearance, and material and shape changes. Durability test, aircraft ground test and flight test were carried out to verify the improved shape, and it was confirmed that the wiping performance and clearance problems were solved. Currently, the rotorcraft is operated without problem by applying the improved shape, and this design improvement process will be a useful reference for future rotorcraft development.

• Asian Journal of Turfgrass Science
• /
• v.23 no.2
• /
• pp.229-240
• /
• 2009

The high temperature and water content in soil profile probably affect the physiological disorder especially on cool-season turfgrasses in warm and humid weather of Korean summer. The purpose of this research was to analyze the effect of soil temperature and water content on the growth and stress response of creeping bentgrass(Agrostis palustris Huds.) under a humid and warm temperature. USGA(United State of Golf Association) green profile in laboratory test, Daily temperature changes were tested under a dried sand, 70% water content of field capacity, and saturated condition at $34^{\circ}C$ of the USGA green in lab. In this test, the dried sand reached to $80^{\circ}C$, however, the surface temperature decrease of $10^{\circ}C$ on the saturated condition. In the thermal properties test in field, thermal conductivity, thermal diffusivity, and soil temperature were increased followed by irrigation practise. In the water-deficient condition, the highest soil temperature was reached temporally right after irrigation, however, the excessive soil water content higher than field water holding capacity showed the highest soil temperature after a while. This result indicated that a heat damage to root system was caused from the thermal conductivity of a high surface soil temperature. The excessive irrigation when a high turf surface temperature should occur a negative result on tufgrass growth, moreover, it would be fatal to root growth of creeping bentgrass, especially when associated with a poor draining system on USGA sand green. Overall, this study shows that high soil temperature with water-excessive condition negatively affects on cool-season grass during the summer season, suggesting that excessive irrigation, over 70% field capacity of soil condition, does not help to reduce soil temperature for summer season in Korea. In the study that cool-season grass were treated with different water content of soil, The soil had higher temperature and more water holding capacity when treatment rate of soil conditioner was increased. The best growth at the normal water condition and the worst state of growth at thee water-excessive condition were observed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.1
• /
• pp.41-51
• /
• 2018

Downwash from helicopter rotor blades and external winds from various maneuvering make an unguided rocket change its trajectory and range. For the prediction of the trajectory and range, it is essential to consider the downwash effect. In this study, an algorithm was developed to calculate 6-Degree-Of-Freedom(6 DOF) forces and moments exerting on the rocket, and total flight trajectory of a 2.75-inch unguided rocket in a helicopter downwash flow field. Using Actuator Disk Model(ADM) analysis result, the algorithm could analyze the entire trajectory in various initial launch condition such as launch angle, launch velocity, and external wind. The algorithm that considered the interference between a fuselage and external winds could predict the trajectory change more precisely than inflow model analysis. Using the developed algorithm, the attitude and trajectory change mechanism by the downwash effect were investigated analyzing the effective angle of attack change and characteristics of pitching stability of the unguided rocket. Also, the trajectory and range changes were analyzed by considering the downwash effect with external winds. As a result, it was concluded that the key factors of the rocket range change were downwash area and magnitude which effect on the rocket, and the secondary factors were the dynamic pressure of the rocket and the interference between a fuselage and external winds. In tailwind case which was much influential on the range characteristics than other wind cases, the range of the rocket rose as increasing the tailwind velocity. However, there was a limit that the range of the rocket did not increase more than the specific tailwind velocity.

• Journal of Radiation Protection and Research
• /
• v.36 no.2
• /
• pp.59-63
• /
• 2011

It is important to reduce indirect scattered neutron beside direct neutron of chosen energy for designing a neutron-reference-field laboratory with neutron produced from a nuclear reaction by a accelerator. Therefore MCNPX simulation was performed with various conditions for obtaining such condition. At first in the original laboratory condition we calculated the direct neutron flux which was inserted in chamber (virtual chamber composed of air) of 0 degree (proton moving direction) for neutron flux measurement and the scattered neutron flux which is inserted in the chamber after scattering wall or bottom. In the result, the scattered neutron which was inserted after scattering bottom is more than that which was inserted after scattering the others. Therefore MCNPX simulation was again performed with removing the concrete bottom and with removing the concrete bottom and digging 1 m in the ground. In the result of removing concrete bottom and digging 1 m in the ground, scattered neutron which was inserted after scattering bottom became less than that which was inserted after scattering the others.

• International Journal of Highway Engineering
• /
• v.10 no.1
• /
• pp.97-104
• /
• 2008

Many atypical structures on the roadside are exposed to traffics unshielded posing great danger. One way to shield an atypical structure to secure the occupant safety is to stack energy absorbing material modules in front of the structure. This paper presents the analysis method of module type crash cushion made of EPS blocks using simple energy balance of the car and crash cushion and numerical examples for 0.9ton-500km/h, 0.9ton-60km/h and 0.9ton-70km/h impact are presented. This method gives simple estimation of maximum acceleration, time of crash, whether or not the vehicle stops completely before whole cushion is being crushed. However, since the acceleration and velocity data from the analysis is so crudely spaced that calculation of safety indices such is RA and OIV is not possible. Problem is overcome by using data interpolation. The spline and linear interpolation is introduce and safety analysis is made and the results are compared.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.413-422
• /
• 2011

A battery is an important part of the component, as a power source of the control of rolling stock at starting movement or emergency control. Now widely used batteries are Ni-Cd batteries and lead accumulators, and these are increasingly getting smaller and lighter. In addition, the electric capacity required is increasing, due to the development of electronic control technology of rolling stock. Therefore, various kinds of high-efficiency battery are considered for the new routes' rolling stock, but rolling stock's batteries should be fully tested to prove safety and also have no difficulty in terms of management, so because of the requirement, it is difficult to be in practical application. In this paper, we will survey cases of applying battery to rolling stock and then we will review whether there is any problem about safety and performance, management to discuss future trend of batteries.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.153-153
• /
• 2017

본 연구에서는 농작업지내 모서리 점을 이용하여 자율주행 트랙터의 경로점을 생성하는 알고리즘을 개발하였다. 작업지는 직사각형의 형태에서 거리가 긴 방향으로 직선주행 경로로 하고, 직선경로의 수는 작업폭에 의해 결정되며 홀수 또는 짝수 개일 수 있다. 또한 TM좌표계에서 직선주행 경로의 기울기는 양수 또는 음수 일 수 있으며, 선회시 전체적으로 좌회전 또는 우회전하는 경우로 구분하여, 즉 총 8가지의 경우에 대하여 조건이 주어지면 경로점을 구할 수 있도록 프로그램하였다. 선회를 위한 곡선경로 생성에는 트랙터의 최소 회전반경 데이터를 사용하였으며, 이때 새로 진입할 다음 경로가 충분히 떨어져 있는 경우에는 선회 구간에서도 직선 경로 구간이 생길 수 있음을 고려하였다. 한 주기의 경로점은 직선 경로 구간의 시작점과 끝점, 선회 구간의 시작점과 끝점, 다음 직선경로로 진입을 위해 선회하기 직전까지의 직선 구간에 대한 시작점과 끝점 등 6가지의 경우로 구분할 수 있다. 이때 어떤 끝점 경로점은 다음 조작 구간의 시작점 경로점이 되므로 최종적인 경로점 데이터는 4개가 된다. 여기서, 첫 번째 경로점 생성에서는 직선구간 진입을 위한 선회구간의 시작점과 끝점은 제외하였으며, 작업지로 진입할 수 있는 입구와 출구는 동일한 것으로 가정하여, 작업이 완료되는 지점에서 선회하여 다시 출발점으로 돌아올 수 있도록 추가 구성하였다. 실제 상황에서는 직선주행 경로의 수가 정수가 되지 않을 수 있으며, 이때는 작업 구간이 약간씩 오버랩되도록 작업폭을 조정하여 경로의 수가 항상 정수가 되도록 하였다. 알고리즘 평가에 사용된 작업 패턴은 관행적인 방법으로서 작업 포장을 반으로 나누어 8자형 패턴을 이용하였다.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.197-202
• /
• 2010

Post release mechanism is generally used to reduce the severity of the occupant of an errant vehicle impacting a roadside posts. The 820kg-50km/h head-on impact simulations were made using LS-DYNA program for the posts of 101.6mm Dia(t=4.0mm) with and without clip-type release mechanism. The simulation result was compared with impact test result to enhance the credibility of simulation model. The study shows that the high impact severity (THIV, PHD) and excessive deformation threatens the safety of the occupant when a car impacts a rigidly connected posts, while a post with clip-type slip base reduce the impact severity to a safe level.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.3
• /
• pp.1085-1090
• /
• 2011

To assure the safety of rolling stock, it is important to perform the fatigue analysis of reduction gear unit in rolling stock considering a variation of velocity and traction motor capability. This paper presents fatigue analysis of the damage of reduction gear unit of railway vehicle under variable amplitude loading(VAL) based on quasi-static fatigue analysis using finite element model and linear Miner's rule. The VAL for the simulation was constructed from the tractive effort curve and train run curves of railway vehicle under commercial operation condition using MSC.ADAMS dynamic analysis. The finite element model for evaluating the carburizing effect on the gear surface was used for predicting the fatigue life of the middle gear based on strain-life based approach. The results showed that the frequent high starting torque due to a quick start as well as increasing numbers of stops at station would decrease the fatigue life of reduction gear unit.