• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.705-708
• /
• 2008

Diatomite, bentonite and zeolite were used as porous materials for fabricating hygroscopic panels. Moisture adsorption and desorption of porous materials were investigated and hydrothermal method was applied to fabricate panels. Cheolwon diatomite and Pohang zeolite showed excellent characteristics of moisture adsorption and desorption. These characteristics were caused by higher surface area and pore volume of porous materials. Moisture adsorption contents were influenced by surface area and pore volume of panels, and surface area more effected on moisture adsorption. Moisture adsorption content of panel with 10% Pohang zeolite was 180g/m$^2$and that of 10% Cheolwon diatomite was 170g/m$^2$. Moisture desorption content of panel with 10% Pohang zeolite was 105g/m$^2$. Moisture adsorption contents of panel with porous materials were higher than that of panel without porous materials.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.137.1-137.1
• /
• 2010

SOFC cell 하나의 전위차는 약1.1V이기 때문에 발전용으로 사용하기 위해서는 수많은 단전지를 직렬로 연결하는 구조가 필요하다. 이러한 stack의 디자인에서 발생하는 문제를 획기적으로 개선한 형태가 하나의 지지체에 셀을 직렬로 연결함으로 전극의 선폭 및 단위 셀 간의 간격이 기존 평판형, 원통형에 비해 대폭 축소되어 전극 및 연결재의 저항손실을 최소화할 수 있는 Segmented형 SOFC이다. Segmented SOFC에 적용하기 위한 세라믹 다공성 지지체는 연료와 공기에서의 화학적 안정성, 셀의 구성소재와 반응이 없으며 열팽창계수가 유사해야하는 특성을 가져야하는데 그 중에서도 지지체로써 적절한 기계적 강도와 높은 가스투과도가 요구되어진다. 본 연구에서는 고온에서 안정한 Spinel의 MgAl2O4를 주성분으로 하는 다공성 지지체를 압출 성형하여 평관형으로 제조하였으며 활성탄을 기공형성제로 사용하여 연료의 공급이 원활하도록 약 30%의 기공율을 가지는 다공성 세라믹 지지체를 제조하였다. 제조된 세라믹 지지체에 연료극(NiO/YSZ), 전해질(TZ8Y), 공기극(LSM)을 코팅하여 실제 SOFC에 적용이 가능함을 확인하였다.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05a
• /
• pp.33-35
• /
• 2012

본 연구에서는 전이금속 Cu, Mn이 함침된 제올라이트를 사용하여 일산화탄소의 흡착능을 연구하였다. 금속 복합 산화물촉매 제조는 Cu, Mn을 서로 다른 비율로 물리 혼합하여 지지체에 담지하였다. 제올라이트 분자체는 상용 13X를 사용하였다. 함침방법은 과잉용액 함침법을 사용하였고, 건조 후 소성 하여 산화물 형태로 담지하였다. 합성된 개질 흡착제의 표면특성 분석은 $N_2$흡착 및 탈착곡선을 통한 질소흡착 특성 분석으로 기공크기, 기공분포, 비표면적을 구하였으며, FT-IR, X-선 회절분석, 전자주사현미경, $NH_3$-TPD/TPR 으로 특성을 분석하였다. 흡착 실험은 고정층 반응기에서 수행하였으며, 내경 4 mm 석영관에 흡착제를 충진하고 흡착파과곡선을 Gas Chromatograph로 측정하여 Cu-Mn 제올라이트 촉매의 일산화탄소 흡착 성능을 연구하였다. Cu-Mn 함량 비율과 흡착조업조건에 따른 흡착능을 측정하여 최적 흡착조건을 구하였다.

• Journal of Technologic Dentistry
• /
• v.23 no.2
• /
• pp.151-160
• /
• 2002

The purpose of this study was to evaluate the influence of sprue joint form on castability in dental prosthetics. The researcher carried out experimental study according to the type was divided by sprue joint form. Therefore type A was made thicken than sprue diameter of type B and type C was made it conversely. The results were as follows: 1. In the order of castability, type C(87.8%) was first and then type A(87.0%) and type B(79.2%) was last. However there was no significant difference statistically. 2. If reservior was located at the correct position and in sufficient size, internal shrinkage porosity in the casting bodies were not generated in the type of all. 3. At the reservoir, internal shrinkage porosity was generated first in type A, followed by type Band type C in the order named. Although it gives no impact on casting body, porosity seems to appear the least when it's produced in the form of type C.

• Journal of Technologic Dentistry
• /
• v.36 no.3
• /
• pp.205-217
• /
• 2014

Purpose: This study will examine the differences among the college dental morphology textbooks in light of their contents and learning objectives through which we will propose an optimal way of consolidating those differences found. Methods: Five college textbooks adopted in the dental related departments were selected by random and the overview and subdivisions of contents were compared and closely analysed with regards to the learning objectives. Results: Firstly, all of the dental morphology textbooks cover the learning objectives of the dental morphology subject, especially in the area of the overview of dental morphology, the permanent tooth, deciduous tooth. Only the dentistry textbooks explain the learning objective of the occlusion. Secondly, differences in content were found in the area of component tissue and around tissue, dental formula of deciduous teeth, spinous process, buccal pit, enamel projection, curve symbol, tip of cusp position of proximal surface of permanent mandibular canines, buccal cusp position of permanent mandibular second premolars. Conclusion: It is imperative to delineate some meaningful and critical differences in contents among the dental morphology textbooks and reflect this to each and every textbook to be published as a supplementary information guide or index.

• Journal of Technologic Dentistry
• /
• v.34 no.2
• /
• pp.67-73
• /
• 2012

연구 목적: 임플란트의 하부구조를 상부 구조와 연결하는 레진시멘트의 접착강도를 높이기 위한 기계적 화학적인 표면처리 방법들이 연구 되고 있다. 이 연구에서 다양한 크기의 $Al_2O_3$ sandblasting과 Silano Pen으로 표면처리한 티타늄과 레진 시멘트의 접착강도를 알아보고자 한다. 연구 방법: 12개의 티타늄(Ti-6A1-4V)시편을 디스크 형태로 제작하여 자가중합 수지에 매립하였다. 이들을 각각 6개의 군으로 나누어 $50{\mu}m$, $90{\mu}m$, $110{\mu}m$ 등 3가지 크기의 $Al_2O_3$로 sandblasting 하는 조건과 $Al_2O_3$로 sandblasting한 후 Silano Pen(Bredent, bredent GmbH &Co.KG, Senden, Germany)을 사용한 군으로 나누었다. 표면처리 한 티타늄 표면에 레진시멘트(Duolink dual syringe, Bisco, USA)으로 접착하였다. 그 후 증류수($37^{\circ}C$)에 24시간 보관 후 접착강도 실험을 시행하였고, SEM을 사용하여 표면처리 한 표면과 접착강도 실험 후 파절양상을 관찰하였다. 결과: 통계학적 분석에 따르면 Silano Pen을 사용하여 표면처리한 군들의 접착강도가 높았다(P<0.05). 결론: Silano Pen을 사용하는 것이 티타늄과 레진시멘트의 접착강도를 증가 시킨다.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1306-1311
• /
• 2009

In recent semiconductor manufacturing clean rooms, in order to improve clean room air quality, air washers are used to remove airborne gaseous contaminants such as $NH_3$, SOx and organic gases from the outdoor air introduced into clean room. Meanwhile, there is a large amount of exhaust air from a clean room. From an energy conservation point of view, heat recovery is therefore useful for reducing the outdoor air conditioning load for a clean room. Therefore it is desirable to recover heat from the exhaust air and use it to reheat the outdoor air. In the present study, numerical analysis and experiment was conducted to simulate the amount of energy reduction of exhaust air heat recovery type air washer system. The present numerical results showed good agreement with the results of the experimental data.

• Journal of Technologic Dentistry
• /
• v.22 no.1
• /
• pp.79-88
• /
• 2000

The objective of this finite element method study was to analyze the stress distribution induced in a maxillary central incisor Ni-Cr base metal coping ceramic crowns with various margin design. Margin designs of crown in this experiment were knife-edge metal margin on chamfer finishing line of tooth preparation(M1), butt metal margin on shoulder finishing line(M2), reinforced butt metal margin on shoulder finishing line(M3), beveled metal margin on bevelde shoulder finishing line(M4). Two- dimensional finite element models of crown designs were subjected to a simulated biting force of 100N which was forced over porcelain near the lingual incisal edge. Base on plane stress analysis, the maxium von Miss stresses(Mpa) in porcelain venner was 0.432, in metal coping was 0.579, in dentin abutment was 0.324 for M1 model, and M2 model revealed in porcelain was 0.556, in metal coping was 0.511, in dentin was 0.339, and M3 model revealed in porcelain was 0.556, in metal coping was 0.794, in dentin was 0.383 for M4 model. All values of each material in metal-ceramic crown were much below the critical failure values.

• Journal of Technologic Dentistry
• /
• v.34 no.4
• /
• pp.473-482
• /
• 2012

Purpose: The purpose of this study was to investigate the stress distribution of the surrounding tissues according to 3 proximal plate types of the RPI clasp. Methods: The removeable partial denture which mandibular right and left second premolars and mandibular molars were lost was attached to a three dimensional photo elastic epoxy resin model. Then 120N of vertical load was applied. After 3-dimensional photoelastic stress analysis was used to record the isochromatic fringe patterns. Results: Kratochvil type guiding plane exhibited little uniform stress distribution on load center and alveolar ridge, but higher stress concentration on buccal surface of second premolar. Krol type guiding plane exhibited the stress concentration on the front of load center and relatively higher stress concentration on buccal surface of first premolar. However, this type had no effect on canine. Researcher type guiding plane showed the stress concentration on second premolar and molar, but the little stress distribution on first premolar. Conclusion: In all types, excessive stress concentration was appeared and three types were not significant different.

• Journal of Technologic Dentistry
• /
• v.21 no.1
• /
• pp.87-96
• /
• 1999

In order to examine the influence of sprue(used to make crown supplements) on casting, 3 kinds of sprue materials(wax, wood, plastic) and 3 types of sprue(round, square, triangle) were made and buried and cast, then the comparison and analysis of casting characters among sprue materials and among sprue type show the following results : 1. The comparison of casting characters in accordance with sprue materials shows wax sprue of 83.3%, wood sprue 81.3%, and plastic sprue of 80.7%, Wax sprue was the bast materials for casting, However there was no statistically significant difference of casting characters among was, plastic and wood. 2. The comparison of casting in accordance with sprue types shows square sprue of 94.0%, round sprue of 86.9% and triangle sprue of 84.2%. square sprue had a best casting character. 3. When a ring cast using wood sprue was classified from burying materials. its cutting of casting body and sprue indicated much more than any other sprue material. It seems to be caused by the influence of wood residuals and carbon occurrence.