• Resources Recycling
• /
• v.24 no.6
• /
• pp.31-37
• /
• 2015

Ground granulated blast-furnace slag (GGBFS) which is by-product of steel industry has been recycled as a cement admixture though the other steel slags are used as aggregates. In this study, the electric arc furnace slag (EAFS) was used as a cement admixture after the reduction of iron oxide in the slag at the interface of molten slag and water quenching. Consequently, the reformed EAFS (REAFS) had higher grindability than that of granulated blast furnace slag. And in mortar tests, the strength properties of specimens using REAFS were 98% of plain specimens of GGBFS upto 20% replacement ratio of GGBFS with REAFS.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.391-395
• /
• 2005

This paper has comparatively analyzed the characteristics of the machined surface of a specimen made by machining Die Steel STD11 and a specimen obtained by W-EDM steel. If a press die is manufactured through W-EDM, products of shapes that cannot easily be made through machining can be manufactured easily. However, the life of the press die is significantly reduced compared with the press die made through machining. This is believed to be caused by the deformed layer that has occurred on the surface of the press die that was made through W-EDM. The roughness of the 2 specimens was measured, and it was learned that the distribution of the roughness of the specimen made through the 1st W-EDM was rough. When the specimens were observed using a scanning-electron microscope, there was significant difference between the surface and the cross-section of the 2 specimens, while the cross section of the specimen obtained through W-EDM had the tempered and quenched surface structure which exists in the form of a deformed layer.

• Journal of the Korean Society of Safety
• /
• v.35 no.5
• /
• pp.128-136
• /
• 2020

In the present experimental study, the effect of water-based iron(III) oxide nanofluid on the MFB(Minimum Film Boiling) point during quenching was investigated. As the highly heated test specimen, the cylindrical stainless steel rod was used, and as the test fluids, the water-based iron(III) oxide nanofluids of 0.001 and 0.01 vol% concentrations were prepared with the pure water. To examine the effect of location in the test specimen, the thermocouples were installed at the bottom and middle of wall, and center in the test specimen. Through a series of experiments, the experimental data about the influences of nanofluid concentrations, the number of repeated experiments, and locations in the test specimen on the reaching time to MFB point, MFBT(Minimum Film Boiling Temperature), and MHF(Minimum Heat Flux) were obtained. As a result, with increasing the concentration of nanofluid and the number of repeated experiments, the reaching time to MFB point was reduced, but the MFBT and MHF were increased. In addition, it was found that the effect of water-based iron(III) oxide nanofluid on the MFB point at the bottom of wall in the test specimen was observed to be greater than that at the middle of wall and center. In the present experimental ranges, as compared with the pure water, the water-based iron(III) oxide nanofluid showed that the maximum reduction of reaching time to MFB point was about 53.6%, and the maximum enhancements of MFBT and MHF were about 31.1% and 73.4%, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.6
• /
• pp.465-474
• /
• 2014

To validate the accuracy of the boiling heat flux partitioning model, an experiment was performed to investigate how the wall heat flux is divided into the three heat transfer modes of evaporation, quenching, and single-phase convection during subcooled nucleate boiling on a vertical wall. For the experimental partitioning of the wall heat flux, the wall heat flux and liquid-vapor distributions were simultaneously obtained using synchronized infrared thermometry and the total reflection technique. Boiling experiments of water with subcooling of $10^{\circ}C$ were conducted under atmospheric pressure, and the results obtained at the wall superheat of $12^{\circ}C$ and average heat flux of $283kW/m^2$were analyzed. There was a large difference in the heat flux partitioning results between the experiment and correlation, and the bubble departure diameter and bubble influence factor, which account for a portion of the surrounding superheated liquid layer detached by the departure of a bubble, were found to be important fundamental boiling parameters.

• Economic and Environmental Geology
• /
• v.50 no.2
• /
• pp.105-116
• /
• 2017

The purpose of this study is to provide the information on genesis of obsidian occurring in the southwestern part of Ulleung Island, Korea, and to discuss its implications for volcanic activity through volcanological and mineralogical properties of obsidian. Obsidian occurs locally at the lower part of the Gombawi welded tuff, showing various complex textures and flow banding. Though obsidian is mostly homogeneous, it is closely associated with alkali feldspar phenocrysts, reddish tuff, and greyish trachyte fragments. The obsidian occurs as wavy, lenticular blocks or lamination composed of fragments. Cooling fractures developed on obsidian glass are characterized by perlitic cracks, orbicular or spherical cracks, indicating that obsidian rapidly quenched to form an amorphous silica-rich phase. It is evident that hydration took place preferentially at the outer rim relative to the core of obsidian, forming alteration rinds. The glassy matrix of obsidian includes euhedral alkali feldspars, diopside, biotite, ilmenite, and iron oxides. Microlites in glassy obsidian are composed mainly of alkali feldspars and ilmenite. Quantitative analysis by EPMA on the obsidian glass part shows trachytic composition with high iron content of 3 wt.%. Accordingly, obsidian formed with complex textures under a rapid cooling condition on surface ground, with slight rheomorphism. Such results might be induced by collapse of lava dome or caldera, which produced the block-and-ash flow deposit and the transportation into valley while keeping high temperatures.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2001.04a
• /
• pp.9-10
• /
• 2001

용융공정 $YBa_2Cu_3O_{7-x}$(123) 초전도체는 고자장 하에서도 통전특성이 우수하다 그러나 123 초전도체에는 미세균열이나 기공과 같이 초전도체의 통전특성에 유해 한 요인들도 다수 포함된다. 미세균열은 고온 정방정 상이 저온 사방정상으로 상변 태 시 발생하는 웅력에 의해 생성된다. 반면, 기공은 123 성형체를 녹이는 과정에서 123 상에 포함된 산소원자들이 격자로부터 이탈되고, 이 산소원자들이 모여 액상에서 기공을 형성한다. 제조공정에 따라 기공의 크기와 밀도가 다르지만 대략 수십 이크론 정도로 대단히 크다 생성된 기공 중 일부는 열처리 중에 소멸되나, 어떤 것들은 그대로 남아 초전도체의 치밀화를 방해한다. 본 연구에서는 123의 용융 및 $YBa_2Cu_3O_{7-x}$(211)과 액상으로의 분해 과정 및 포정반응과 관련된 미세조직을 조사하여 기공생성과 소멸과정을 조사하였고, 123의 최종 미세조직에 대한 기공의 영향에 대 하여 연구하였다. 열처리 스케쥴은 123-211-액상의 그림 l의 2원 상태도를 기초로 하여 결정하였다. 먼저 부분 용융상태에서의 기공의 분포를 알고자 시편을 105$0^{\circ}C$에서 0.5-1 시 간 유지한 후, 액체 질소통에 넣어 냉각하였다 (그림 2의 열처리 경로 CD)$\circled1$부분 용 융상태에서 급랭할 경우 211과 액상 상태가 그대로 유지되므로 액상에서의 기공분 포를 관찰할 수 있다. 또 다른 시편들은 그림 2의 @$\circled2$경로로 열처리하였다. 이 시편에서는 고온에서 생성된 211과 액상이 반웅하여 123 결정이 생성, 성장하므로 123 결정립 내의 기공분포를 알 수 있다. 그림 3은 시편에서의 기공과 액상포켓의 분포를 모식도와 각 부위의 미세조직 사진이다. 시편에는 산소가스 발생으로 인해 생성된 수형의 기공이 관찰된다. 기공은 시편의 중앙에 집중되며, 시편 바깥부분은 기공에 액상이 채워진 액상포켓이 관찰된다. 기공의 생성과 소멸과정은 다음과 같다. 출발물질인 123 분말이 211과 액상으로 분해될 때 산소가스가 배출되며, 이로 인해 액상에서 구형의 기공이 생성된다. 이들 중 일부는 액상으로 채워져 소멸되나, 나머지는 그대로 남는다. 특히, 시편 중앙에 서는 수십-수백 마이크론 크기의 커다란 기공이 다수 관찰된는데, 이는 기공의 합체로 만들어진 것이다. 포정반응 열처리 시 기공 소멸로 만들어진 액상포켓들은 주변 211 입자와 반응하여 123 영역으로 변한다. 이곳은 다른 지역과 비교하여 211 밀도 가 낮기 때문에, 미반응 액상이 남거나 211 밀도가 낮은 123 영역이 된다. 액상으로 채워지지 못한 구형의 기공들 중 다수가 123 결정 내로 포획되며, 그 형상은 액상/ 기공/고상 계면에너지에 의해 결정된다.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.438-445
• /
• 2002

In this study, the glass frit of $PbO-TiO-2-SiO_2-BaO-ZnO-Al_2O-3-CaO-B_2O_3-Bi_2O_3-MgO$ system was manufactured. The glass was melted at $1,400{\circ}C$, quenched and attrition-milled. The glass frit powder was pressed and fired for 2h at the range of $750~1,000{\circ}C$. The crystallization of glass frit began at about $750{\circ}$ and at low temperature, the main crystal phases were hexagonal celsian($BaAl_2Si_2O_8$) and alumina. As the firing temperature increased, the crystal phases of monoclinic celsian, zinc aluminate, zinc silicate, calcium titanium silicate and titania appeared. And the increase of firing temperature led to transformation of hexagonal celsian to monoclinic. The only glass frit containing 15wt% PbO had the crystal phase of solid solution of $PbTiO_3-CaTiO_3$. At the frequency of 1 MHz, the dielectric constant of glass frit crystallized was in the range of 11~16 and the dielectric loss less than 0.020. But the glass frit containing 15wt% PbO had the dielectric constant of 17~26 and loss of 0.010~0.015 because of crystal phase of solid solution of $PbTiO_3-CaTiO_3$.

• Journal of the Korean earth science society
• /
• v.28 no.6
• /
• pp.733-742
• /
• 2007

Petrological, mineralogical, and geochemical analyses were carried on the paleolithic obsidian implements excavated at Wolseongdong, Daegu, Korea. The obsidians has a homogeneous glassy texture that can be observed in a typical obsidian formed from a rapid cooling of silicic magma. Major element composition of the obsidians represent calc-alkaline series. Comparing those with other obsidians from domestic local excavation sites, Mt. Baekdu, and Kyusu of Japan, the Wolseongdong obsidians show similar element distribution pattern with others in spite of small difference in trace and rare Earth element contents. Sr isotopes of the obsidians considerably differ from those of the obsidians from southern part of the Korean Peninsula or from Mt. Baekdu. K-Ar age is approximately 30 Ma, which is much older than Mt. Baekdu (10 Ma). Therefore, considering the characteristics of obsidians found in the Korean Peninsula including mineralogy, petrology, trace element, and isotopes chronology, the obsidians can be divided into four groups: Mt. Baekdu, southern part of Korea (Kyusu of Japan), middle part of Korea, and Wolseongdong region. These groups suggest a possibility of more than four different origins of the obsidians found in the Korean Peninsular.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.31 no.4
• /
• pp.90-100
• /
• 2003

본 연구는 기존 건축물 옥상녹화에 이용 가능한 저토심 옥상녹화 시스템 을 연구하고 개발하고자 수행되었다. 연구목적을 달성하기위해서 시스템의 개념적 모델이 선행 연구로부터 유추되었고 개념적 모델로부터 실험을 위한 시스템들이 제안되었다. 건축물 옥상 위에 설치된 이 시스템들에서 기린초의 생육에 대하여 인공배지 종류, 토심, 그리고 배수 형태의 효과들이 2002년 4월 3일부터 10월 18일까지 연구되었다. 인공배지 종류는 단용과 혼용이고, 토심은 5cm, l0cm,그리고 15cm이며, 배수 형태는 저수$.$배수형과 배수형으로 하였다. 여기서, 인공배지 단용은 폐유리 미분 100에 발포제를 1∼2정도 첨가하고, 착색제를 1정도 첨가한 후, 6∼8$^{\circ}C$/min로 승온하여 750∼85$0^{\circ}C$의 온도에서 발포시킨 다공질 유리를 수냉식으로 급랭하고, 분쇄기로 이송하여 l0mm이하로 분쇄하고 입도를 조절하여 얻어진 다공질 유리 파쇄물과 수피를 부피 비 6:4로 혼합하여 조성된 것이며 인공배지 혼용은 인공배 지 단용에 양토(모래 46%, 미사 40%, 점토 14%)를 부피비 5:5로 혼합하여 조성된 것이다. 피복면적, 지상부와 지하부의 생체중과 건물중, 그리고 시각적 질을 조사하였다. 각 변수들은 던칸의 다중범위 검정으로 통계처리 하였으며 처리들간의 유의수준은 5%였다. 그리고 기존 건축물 옥상에 대한 과부하의 위험을 피하기 위해서 각 시스템의 중량이 평가되었다. 그 결과를 요약하면 다음과 같다. 실험기간 중에 피복면적에 대한 배수 형태의 효과는 유의성 있는 차이를 나타내지 않았다. 인공배지 혼용의 피복면적은 인공배지 단용의 것보다 통계적으로 유의성 있게 높았다. 토심 5cm처리의 피복면적은 나머지 처리들의 피복면적보다 통계적으로 유의성 있게 낮았다. 토심 l0cm처리와 토심 15cm처리는 통계적으로 유의성이 없는 것으로 나타났다. 지상부와 뿌리의 생체중 및 건물중과 시각적 질에 대한 처리들의 효과는 피복면적에 대한 것과 유사하거나 동일하였다. 결과적으로, 기린초의 생육은 인공배지 단용보다 인공배지 혼용에서 더 높았고, 토심 10∼15cm에서 더 높았으며, 배수 형태에서는 뚜렷한 차이를 나타내지 않았다. 이 결과를 토대로, 기존 건축물 옥상에 적용 가능한 시스템의 허용하중과 기린초의 생육을 동시에 고려해볼 때, 저토심 옥상녹화 시스템 은 인공배지 종류에서는 혼용이, 토심은 10cm, 그리고 배수형태는 배수형이 적합하다고 보았다. 제안된 조건으로 조성된 시스템은 인공배지가 포장용수량상태일 때 그 중량이 약 115kg/$m^2$정도로 나타났다.

• Resources Recycling
• /
• v.25 no.2
• /
• pp.49-59
• /
• 2016

Steel slag is being recycled into industrial by-products for civil generated inevitably in the seasonal course, road and cement raw materials. However, the field of recycling most of the bottom portion is concentrated in the areas that are required to take advantage of the situation in various fields taking advantage of the steel slag. But various studies to take advantage of the steel slag as aggregate for concrete made for limiting slag was a situation that most of the studies are incomplete research on the suitability of as aggregate for concrete practical relates to an expandable suppressed. In this study, the separation of the slag aggregate according to the production methods to assess the feasibility aggregate for concrete aggregates, including through Steel making slag, a total of seven kinds of steel slag aggregate. Studies show that ordinary concrete, steel slag aggregate for aggregate and on the equally to take advantage of grading, chloride content standards such as to what is lacking, although appropriate aggregate of concrete include the deployment of only in special sectors through the combination was assessed to have a very high.