• Analytical Science and Technology
• /
• v.13 no.1
• /
• pp.27-33
• /
• 2000

Simultaneous separation and analysis of Ni(II), Pd(II), Co(II), Cu(II) and Hg(II) in peperidinedithiocarbamate (PDTC) chelates were investigated by reversed phase liquid chromatography. The optimum conditions for the separation of PDTC metal chelates were examined with respect to the pH, extraction solvent, and mobile phase strength on Novapak $C_{18}$ column using methanol/water mixture as mobile phase. All metal PDTC chelates were eluted in an acceptable range of capacity factor value ($0{\leq}log\;k^{\prime}{\leq}1$). The linear calibration curves were obtained in the concentration range of $0{\sim}1.2{\mu}g/mL$ for five metal ions, and also good precision in the range of 1.96~3.41% RSD was obseved. Under the optimum conditions, trace metat ions in the composite water sample were successfully separated and determined with relative error of ${\pm}2.0%$.

• Resources Recycling
• /
• v.31 no.1
• /
• pp.12-20
• /
• 2022

The smelting reduction of spent lithium-ion batteries results in metallic alloys containing Co, Cu, Fe, Mn, Ni, and Si. A process to separate metal ions from the sulfuric acid leaching solution of these metallic alloys has been reported. In this process, ionic liquids are employed to separate Fe(III) and Cu(II). In this study, D2EHPA and Cyanex 301 were employed to replace these ionic liquids. Fe(III) and Cu(II) from the sulfate solution were sequentially extracted using 0.5 M D2EHPA with three stages of cross-current and 0.3 M Cyanex 301. The stripping of Fe(III) and Cu(II) from the loaded phases was performed using 50% (v/v) and 60% (v/v) aqua regia solutions, respectively. The mass balance results from this process indicated that the recovery and purity percentages of the metals were greater than 99%.

• Clean Technology
• /
• v.22 no.3
• /
• pp.161-167
• /
• 2016

Catalytic combustion of benzene over various metal cation-exchanged zeolites has been investigated. Y(4.8)-type zeolite showed the highest activity among the used zeolites and Cu/Y(4.8) catalyst also showed the highest activity among metal cation/ Y(4.8) zeolites. The catalytic activity increased according to the amount of adsorbed oxygen acquired from O₂ TPD results. The catalytic activity also increased with an increase of Cu cation concentration on Cu/Y(4.8) catalysts. The conversion of benzene on the combustion reaction depended on not benzene concentration but the oxygen concentration. In addition, the introduction of water into reactants decreased the catalytic activity.

• Journal of environmental and Sanitary engineering
• /
• v.15 no.1
• /
• pp.25-33
• /
• 2000

The new ion exchange resin was synthesized from chloromethylated styrene-1,4-divinylbenzene(DVB) with 1-aza-15-crown-5 macrocyclic ligand by substitution reaction. The effect of pH, time, dielectric constant of solvent and cross-linked of the matrix on the adsorption for $UO_2^{2+}$, $Ca^{2}$ and $Lu^{3+}$ was investigated. The metal ion was not adsorbed on the resins below pH 3 but above pH 4 fast adsorption behavior was showed. The optimum equilibrium time for adsorption of metallic ions was two hours. The adsorption selectivity determined in ethanol matrix was in increasing order $UO_2^{2+}>Ca^{2}>Lu^{3+}$. The adsorption power was in the order of 1%, 2%, 10% and 20% -crosslinked resin, but adsorption properties of resins decreased in proportion to the order of dielectric constant of solvents used. In addition, these metal ions could be separated in the column packed with 1% crosslinked resin by pH2.5 $HNO_3$ as an eluent.

• Journal of Adhesion and Interface
• /
• v.9 no.2
• /
• pp.24-31
• /
• 2008

In this work, calcium hydroxide and magnesium carbonate as metal ionic crosslinking agents were used to introduce ionic crosslinking points to the ethylene vinylacetate (EVA) emulsions for the enhancement of water resistance and mechanical properties of emulsion films. The properties of EVA emulsion film were investigated in crosslinking density, thermal features, surface energy, and mechanical properties, such as tensile strength, elongation at break and tear strength. With the increasing content of metal ionic crosslinking agent, the crosslinking density of the EVA emulsion film increases, resulting into the improvement of water resistance. The surface energy and mechanical properties of the EVA emulsion film, however, showed somewhat different behaviors. The highest surface energy, tensile strength, and tear strength were observed when 0.4% for calcium hydroxide and 0.5% for magnesium carbonate was added respectively, because the EVA emulsion containing carboxylic acid forms strong carboxylate-metal bond of ionically-crosslinked system. Therefore, it can be concluded that metal ionic crosslinking agents, such as magnesium carbonate and calcium hydroxide are considered to improve water resistance and mechanical properties of the EVA emulsion.

• Applied Chemistry for Engineering
• /
• v.20 no.2
• /
• pp.165-171
• /
• 2009

Resins were synthesized by mixing 1-aza-15-crown-5 macrocyclic ligand attached to styrene (2th petroleum in 4th class hazardous materials) and divinylbenzene (DVB) copolymer with crosslinkage of 1%, 2%, 8%, and 16% by substitution reaction. The characteristic of these resins was confirmed by content of chlorine, element analysis, thermogravimetric analysis (TGA), surface area (BET), and IR-spectroscopy. The effects of pH, time, dielectric constant of solvent and crosslinkage on adsorption of metal ion by the synthetic resin adsorbent were investigated. The metal ion showed a fast adsorption on the resins above pH 3. The optimum equilibrium time for adsorption of metallic ions was about two hours. The adsorption selectivity determined in ethanol was in an increasing order of uranium $(UO_2^{2+})$ > lead $(Pb^{2+})$ > chromium $(Cr^{3+})$ ion. The adsorption was in the order of 1%, 2%, 8%, and 16% crosslinkage resin and adsorption of resin decreased in proportion to the order of dielectric constant of solvents.

• Analytical Science and Technology
• /
• v.8 no.3
• /
• pp.265-272
• /
• 1995

Schiff base ligand columns and glow discharge detector have been developed for the trace analysis of metal ions desolved in water. Various types of hydrazide Schiff base ligands have been used and, additionally, they were examined as a filling material of a HPLC column. The hydrazide Schiff base ligands used were N, N'-oxalybis(salicylaldehydrazone) (OBSH), N, N'-malonylbis(salicylaldehydrazone) (MBSH), and N, N'-succinylbis(salicylaldehydrazone) (SBSH). A mixture of Schiff base ligand and poly(styrene divinylbenzene) was examined and it showed a smooth flow of solution. The OBSH-polymer column demonstrated different effluent factors for different metal ions. Metal ions in eluates were detected by Hollow Cathode Glow Discharge-Atomic Emission Spectrometry(HCGD-AES). HCGD-AES showed good sensitivity and selectivity. This is only the preliminary results of new OBSH-polymer column and glow discharge detector.

• Journal of the Korean Chemical Society
• /
• v.42 no.4
• /
• pp.443-448
• /
• 1998

The thermodynamic parameters for the interaction of metal ions with dibenzo-16-crown-5 and its derivatives have been determined by solution calorimetry in methanol at 25$^{\circ}C$. Thermodynamic properties of log K, ${\Delta}H$, and $T{\Delta}S$ have been determined for the complexation of metal cations by dibenzo-16-crown-5 and its derivatives. Dibenzo-16-crown-5 and its derivatives have been studied as metal cations carrier in bulk liquid membrane (BLM) and supported liquid membrane (SLM) system. $Ag^+$ has been much more transported using dibenzo-16-crown-5 derivatives as carriers and several other metal cations have been small transported using carrier in BLM and SLM system. Ligand structure, the length of side arm, donor atom, stability constant, and carrier concentration are also important parameters in the transport of cations.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.3
• /
• pp.441-448
• /
• 2016

Heavy metal removal study is conducted from synthetic waste water by reduction and oxidation(redox) reaction of Cu-Zn metal alloy and adsorption reaction of aluminium silicate. Heavy metal whose ionization tendency is smaller than zinc are reducted in an aqueous solution, and the concentration of ionized zinc is reduced by adsorption reaction. The average diameter of metal alloy micro fiber is about $200{\mu}m$, and the surface area is wide enough to get equilibrium in a single cycle treatment. A single cycle treatment of redox reaction of Cu-Zn metal alloy, could remove 100.0 % of Cr(III), 98.0 % of Hg, 92.0 % of Sn and 91.4 % of Cu respectively. An ionization tendency of chromium is very close to zinc, but removal efficiency of chromium by redox reaction is significant. This result shows that trivalent chromium ion is expected to generate hydroxide precipitation with $OH^-$ ion generated by redox reaction. Zinc ion generated by redox reaction is readily removed by adsorption reaction of aluminium silicate in a single cycle treatment. Other heavy metal components which are not perfectly removed by redox reaction also showed very high removal efficiency of 98.0 % or more by adsorption reaction. Aluminium ion is not increased by adsorption reaction of aluminium silicate. That means heavy metal ion removal mechanism by adsorption reaction is turned out to be not an ion exchange reaction, but an adsorption reaction.

• Analytical Science and Technology
• /
• v.9 no.3
• /
• pp.221-234
• /
• 1996

Basic studies for the effective extraction of dibenzylammonium dibenzyldithiocarbamate(DBADBDC) complexes of Ag(I), Pd(II), Au(III) and Pt(IV) into chloroform have been conducted. The effects of pH on the extraction of ligand itself and metal cemplexes showed that DBADBDC itself was uniformly extracted in the pH range of 2~9 and metal complexes were effectively extracted at the pH range as follows. That is, Ag(I) : in an acidic aqua medium, Pd(II) : > 4, Au(III) : wide range, and Pt(IV) : > 3. The distribution ratio and extractabilities were obtained from the partition and extraction equilibria of metal-DBDC complexes between aqueous solution and chloroform. Ag(I) : log D=4.226 : E(%)=99.9% in the aqueous solution of pH 0, Pd(II) : log D=1.804 : E(%)=98.5% at pH 4~7, Au(III) : log D=3.755 : E(%)=99.9% at pH 2~10, and Pt(IV) : log D=0.165 : E(%)=57.2% at pH 8.0. And also mole ratio of metal ion to ligand in complexes were determined by mole ratio method : 1 : 1 for Ag(I) and 1 : 2 for Pd(II), Au(III) and Pt(IV). $Cl^-$ was included as a coordination species in complexes of Au(III) and Pt(IV). Besides, extraction mechanisms of compleses sere examined in the presence of chloride ion in an aquous solution, and extraction reactions and estraction constants could be proposed and calculated, respectively.