• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.641-646
• /
• 2016

Soot particles generated by fossil fuel combustion normally have fractal morphology with aggregates consisting of small spherical particles. Thus, Rayleigh or Mie elastic light scattering theory is not feasible for determining the fractal properties of soot aggregates. This paper describes a detailed process for applying Rayleigh-Debye Gans (RDG) scattering theory to effectively extract the morphological properties of any nano-scale particles. The fractal geometry of soot aggregates produced from an isooctane diffusion flame was observed using ex situ transmission electron microscopy (TEM) after thermophoretic sampling. RDG scattering theory was then used to analyze their fractal morphology, and various properties were calculated, such as the diameter of individual soot particles, number density, and volume fraction. The results show indiscernible changes during the soot growth process, but a distinct decreasing trend was observed in the soot oxidation process. The fractal dimension of the soot aggregates was determined to be around 1.82, which is in good agreement with that produced for other types of fuel. Thus, it can be concluded that the value of the fractal dimension is independent of the fuel type.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.204-210
• /
• 2016

This paper presents an experimental analysis of the growth and oxidation processes of soot particles generated in an isooctane diffusive laminar flame due to incomplete combustion. The effects of iron-based diagnostics were employed to measure the elastic scattering light from soot particles in a flame at different flame heights, and the differential scattering coefficients were calculated through a calibration process. The growth and oxidation of soot particles in flame was investigated by comparing differential scattering coefficients, and the soot volume fraction was seen to decrease in the soot oxidation process. In the same manner, the differential scattering coefficients were calculated for iron-based fuel-additive seeded flame, and these coefficients were revealed to be smaller than those obtained in the fuel-additive unseeded flame. In addition, transmission through the radial direction of the flame was measured, and transmission in the soot oxidation regime was approximately 5% higher for the seeded flame. The propensity of the data coincided well with the differential scattering coefficients, and it can be concluded that the iron component of the fuel additive plays a crucial role as a catalyst, which eventually enhanced soot particle oxidation.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.4
• /
• pp.128-140
• /
• 1996

To analyze a formation process of the soots in spray flame in the combustion chamber, an optically accessible DI Diesel engine was used for visualization. The images of the flames and soots were visualiaed with high speed camera by Schlieren method and Light extinction method. The spray flame and soot images on the films were analyzed at the various engine operating conditions. Soot distributed widely in spray flame and its concentration was about $100g/m^3$ at the position close by nozzle tip of spray flame region, however it decreased below $20g/m^3$ at the corner of combustion chamber due to soot oxidation.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.19 no.1
• /
• pp.40-45
• /
• 1983

The paper describes an experimental investigation of axisymmetric diesel spray and flame which is held in rapid compression machine (RCM) with electromagnetic single injection nozzle. The axisymmetric diesel spray and flame are taken with high speed photograph and analysis it with image processor. The data presented include fuel concentration of spray, flame temperature, soot concentration of flame in axial and radial direction at a moment and compared it with each other.

• Fire Science and Engineering
• /
• v.24 no.5
• /
• pp.128-135
• /
• 2010

In this study, a mixture fraction analysis was performed to investigate the characteristics of chemical species production in compartment fires burning hydrocarbon fuels such as methane, heptane, and toluene. A series of fire experiments was conducted in the ISO 9705 standard room, and gas species concentration and soot fraction were measured at two locations in the upper layer of the compartment. The mass fractions of measured chemical species, such as unburned hydrocarbons (UHC), carbon monoxide (CO), carbon dioxide ($CO_2$), oxygen ($O_2$), and soot were presented as a function of mixture fraction and compared with state relationships based on the idealized reaction of hydrocarbon fuels. The mixture fraction analysis made it possible to rearrange hundreds of species measurements, which were done under various fire conditions and at two locations of the upper layer, in term of the unified parameter, i.e. the mixture fraction. The results also showed that inclusion of soot in the mixture fraction calculation could improve the performance of analysis, especially for the sooty fuels such as heptane and toluene.

• 보일러설비
• /
• s.64
• /
• pp.54-55
• /
• 1999

겨울철 난방기가 끝남에 따라 겨우내 사용한 보일러에 대한 손질이 필요한 때가 돌아왔다. 겨울철동안 계속된 가동으로 그을음이 끼거나 무리가 가해진 보일러를 그냥 방치해 둘 경우 연소효율이 떨어지거나 수명이 단축되는데 간단한 청소나 손질로 이를 예방할 수 있다. 에너지관리공단이 추천하는 간단한 보일러 청소 및 관리 방법을 소개한다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1359-1365
• /
• 2011

The purpose of this study is to investigate the effect of ethanol content on the emission of nanosized particles from a diesel-ethanol blended fuel engine. The engine combustion and exhaust emission characteristics of a singlecylinder diesel engine were analyzed using an emission analyzer and an SMPS(scanning mobility particle sizer). The analysis revealed that soot emission increased with the ignition delay. When the ignition delay was fixed, an increase in the ethanol content caused a decrease in the soot emission. With an increase in the ethanol blending ratio, the number concentration and mass distribution of nanosized particles generally decreased. However, for 30% ethanol blending, large particles were observed because of the agglomeration of soot particles, and consequently, the particle mass increased.

• Fire Science and Engineering
• /
• v.31 no.4
• /
• pp.20-25
• /
• 2017

In the present study, the temperature distribution of droplet diffusion flames was predicted from the measurements of radiative emissions of soot particles formed. In order to predict the temperature distributions, the radiative emissions from soot particles filtered at both 700 nm and 900 nm were measured using CCD cameras and local emission distributions within the flame deconvoluted with Abel transformation were plugged into a two color method. The experimental results obtained from the present study demonstrate that the two color method as tool for temperature measurements is feasible but can introduce approximately 2% maturement errors in a deconvolution process depending on intervals for the line of sight. The estimated error in temperature measurements was found to be within 18 K at 2000 K.

• Journal of Conservation Science
• /
• v.28 no.2
• /
• pp.165-173
• /
• 2012

In this work, scientific and systematic analysis was conducted for finding out the methods and techniques of ancient ink stick making. Analysis the ancient ink stick on ancient documents and wooden writing as letter or painting, we concluded as followings. From the analysis of ancient wood by dendrochronology, wood was cut at 1899, which provided the information on the year of ink stick's made on writing on ancient wood. Single particle size for soot of ancient ink stick was 107 nm for ink on the roof-filling timber in Sinsunwonjeon of Changdeok Palace, compared to 38 to 86 nm on the letter on ancient 12 paper document. Aggregate particle size was 370 nm for ink on the roof-filling timber in Sinsunwonjeon of Changdeok Palace, but 206 to 318 nm for aggregate particle size on 12 paper documents. There was similar pattern between single particle size and aggregate particle size of soot, which might provide the information of raw material for ancient ink. From infra-red and Raman spectroscopic analysis of sheet of writing on paper or wood, there was severe interference from background material (paper or wood). From Raman spectroscopic analysis of ancient ink carefully separated from ancient wood, spectrum pattern was closer to ink stick made by the soot from pine burning.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.12
• /
• pp.1772-1780
• /
• 2003

An optimal soot blowing system has been developed for an optimal operation of power utility boilers by both minimization of the use of steam and the number of soot blowers worked during soot blowing. Traditionally, the soot blowing system has been operated manually by operators. However, it causes the reduction of power and thermal performance degradation because all soot blowers installed in the plant should be worked simultaneously even there are lots of tubes those are not contaminated by slagging or fouling. Heat transfer area is divided into four groups, furnace, convection area including superheater, reheater and economizer, and air preheater in the present study. The condition of cleanness of the tubes is calculated by several parameters obtained by sensors. Then, a part of soot blowers works automatically where boiler tubes are contaminated. This system has been applied in a practical power plant. Therefore, comparison has been done between this system and manual operation and the results are discussed.