• Resources Recycling
• /
• v.29 no.1
• /
• pp.53-61
• /
• 2020

This study aimed to develop a foam concrete material for a ground repair system that has low strength and low fluidity by using an eco-friendly binder, which substitutes industrial by-products for more than 90% of cement. Basic properties were evaluated after substituting a small amount of calcium sulfo aluminate (CSA) for the binder to improve the sinking depth rate and volume change, commonly found when it had a large amount of industrial by-products. The substitution rates of CSA for the eco-friendly binder used for the foam concrete were 2.5, 5, and 10%. Fresh properties, hardened properties, pore structure, and hydrates were analyzed. Experimental results showed that using only 2.5% of CSA could improve the deep sinking depth which occurred when using an eco-friendly binder. As a result, the weight difference between the upper, middle, and lower parts of cast specimens was improved even after being hardened. The addition of CSA also contributed to the formation of small, uniformly sized closed pores and improved initial strength. However, when the proportion of CSA increased, the long-term strength decreased. However, it satisfied the target strength when 5% or less of CSA was used. The results of this study revealed that it was possible to manufacture foam concrete with low strength and high fluidity for repairing ground satisfying target qualities by adding 2.5% of CSA to the eco-friendly binder containing a large amount of industrial by-products.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.107-114
• /
• 2019

In many military aircraft, s-shaped diffusers are used to prevent the fan blades of the turbofan engine from being exposed to the outside. The inlet configurations of the air intakes for military aircraft vary, such as the rectangular intake of the F-22, the crescent-like intake of the F-16, elliptical intake of the MQ-25. In this study, the aerodynamic performance of s-shaped diffusers with various inlet configurations was evaluated using numerical analysis. In addition, the configuration of the middle section of an s-shape duct was changed to the crescent shape, and the effects on its aerodynamic performance were investigated. As a result, there was a slight difference in total pressure recovery according to various inlet configurations with ellipse-shaped middle sections. Also, the total pressure distortion was the lowest in the rectangular inlet shape. When the configuration of the middle section was changed from an ellipse to a crescent shape, the total pressure recovery remained at a high level, except for the ellipse-shaped inlet configuration. In terms of total pressure distortion, the duct with the crescent-shaped middle section showed a significantly more uniform pressure distribution than that with the ellipse-shaped middle section.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2019.04a
• /
• pp.56-56
• /
• 2019

본 연구는 식용과 약용으로 이용되는 국내 자생식물인 야산고비(Onoclea sensibilis var. interrupta Maxim.)를 기내에서 대량증식하기 위한 조건을 구명하기 위하여 수행되었다. 무가온 온실에서 수집한 포자를 기내에서 발아시켜 전엽체를 획득하였으며, 계대배양하며 실험의 재료로 사용하였다. 전엽체의 대량증식을 위해 전엽체 0.3g을 메스로 균일하게 다진 후 증류수 1ml와 함께 배지에 고루 펼쳐서 배양하는 방법을 사용하였으며, 증식에 미치는 배지의 영향을 확인하기 위하여 1/4, 1/2, 1, 2배로 조절한 MS배지를 조성하여 8주간 배양하였다. 이후, 증식이 우수한 배지를 선정하여 sucrose와 질소급원의 농도를 조절하였으며, 활성탄을 첨가하여 증식에 미치는 영향을 확인하였다. 배지종류 실험의 결과, 생체중이 1MS에서 10.2g으로 초기 접종량에 비해 가장 많이 증가하였으며, 현미경을 이용하여 관찰한 결과에서도 정상적인 전엽체의 형태인 심장형으로 발달하였다. 증식이 우수하였던 1MS배지에 sucrose의 농도를 조절하여 배양한 결과에서는 1%의 처리구에서 가장 증식률이 좋았으며, 질소급원의 경우 30mM의 농도로 조절한 처리구가 가장 좋은 결과를 보였다. 배지 내 활성탄의 첨가는 처리구당 증가된 전엽체의 생체중이 유의적인 차이를 보이지 않았다. 포자체 대량 형성을 위한 적정 배양토의 혼합조건을 확인하기 위하여 원예상토, 피트모스, 펄라이트 및 마사토의 혼합비율을 5종류로 달리하여 조성하여 사각분($7.5{\times}7.5{\times}7.5cm$)에 충진하였다. 조성한 배양토에 기내에서 배양한 전엽체 1g을 증류수와 함께 블렌더를 이용하여 10초간 분쇄하여 토양표면에 고루 분주하였다. 이후 12주간 재배한 결과, 모든 토양조합에서 포자체가 형성되었다. 그중 원예상토와 마사토를 2:1(v:v)로 혼합한 토양에서 포트 당 405.0개로 가장 많은 포자체가 형성되었으며, 전체적인 생육 또한 비교적 양호한 결과를 보였다. 따라서 야산 고비의 전엽체 대량증식에 적합한 배지는 경제성과 생육수준을 고려하여 1%의 sucrose와 질소급원의 농도를 30mM로 조절한 1MS 배지가 적합하며, 포자체 대량생산을 위해서는 원예상토, 마사토를 2:1(v:v)로 혼합한 토양이 적합하다고 판단되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.312-320
• /
• 2021

In this study, we aimed to develop a feed additive that can promote the growth of stone flounder (Kareius bicoloratus). To this end, we fermented mealworm medium (5%, w/v) with lactic acid bacteria (LAB) with antibacterial function (HeTm_LpWpPa) and evaluated its efficacy as a feed additive. Fish (approximately 5-6 g) were reared in six completely recirculating tanks (100 fish/tank) for 6 weeks. The total length of fish with and without HeTm_LpWpPa supplementation was 8.26 and 8.42 cm and body weight was 19.71 and 20.28 g, respectively, at 6 weeks. The weight gain of the control and experimental groups was 223.26 % and 248.76 %, respectively. The specific growth rate at 6 weeks was 2.79 % (control) and 2.98% (experimental), and the growth rate of the experimental group was slightly higher (0.19 %) than that of the control group. At the end of the experiment (i.e. 6 weeks), the number of fish below the mean weight in the experimental group was 3 (1 %) and that in the control group was 17 (5.7 %). These results indicate that feed supplementation of 10 % HeTm_LpWpPa could be utilized to promote the growth of flounder in farming.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.5
• /
• pp.217-222
• /
• 2023

The purpose of this paper was to synthesize a polymer organic hard mask that simplifies the manufacturing process, reduces process time significantly, and thereby lowers manufacturing costs. The results of measuring residual metals through vapor refining showed that 9-Naphthalen-1-ylcarbazole(9-NC) measured 101.75ppb in the 4th zone, 2-Naphthol (2-NA) measured 306.98ppb in the 5th zone, and 9-Fluorenone(9-F) measured between 129.05ppb across the 4th and 5th zones. After passing through a filtration system, the synthesized organic hard mask measured residual metals in the range of 9 to 7ppb. Additionally, the thermal analysis indicated a decrease of 2.78%, a molecular weight of 942, carbon content of 89.74%, and a yield of 72.4%. The etching rate was measured at an average of 18.22Å/s, and the coating thickness deviation was averaged at 1.19. For particle sizes below 0.2㎛ in the organic hard mask, no particles were observed. By varying the coating speed at 1,000, 1,500, and 1,800rpm and measuring the resulting coating thickness, the shrinkage rate ranged from 17.9% to 20.8%. The coating results demonstrated excellent adhesion to SiON, and it was evident that the organic hard mask was uniformly applied.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.13 no.3
• /
• pp.286-294
• /
• 2008

In order to understand the physical properties of deep-sea sediments, which mainly consist of pelagic red clays, sediment samples were collected at 24 stations using a multiple corer in the Clarion-Clipperton fracture zone of the northeast equatorial Pacific. The sampled sediment cores were examined for the mass physical properties(i.e. grain size distribution, mean grain size, water content, specific grain density, wet bulk density, void ratio, and porosity) and the geotechnical properties(i.e. shear strength and consistency limits) with the content of biogenic opal and mineral composition. Although KR1 and KR2 areas on the same latitude are logitudinally far from each other, the mass physical properties of these areas are not distinctly different except for shear strengths. The maximum shear strength of surface sediments in KR2 area is higher than that in KR1 due to the appearance of a consolidated lower layer(Unit 3) in the sediment core from KR2.

• Journal of the Korean Society of Radiology
• /
• v.18 no.3
• /
• pp.249-256
• /
• 2024

The study aimed to evaluate the efficacy of treatment plans using full Arc and Partial Arc Coplanar volumetric modulated arc therapy and Non-Coplanar volumetric modulated arc therapy to minimize radiation treatment side effects, such as pneumonia, and protect normal organs in esophageal cancer radiotherapy. 30 patients who underwent Concurrent Chemoradiotherapy for esophageal cancer were included. Compared planning target volume, lung, heart, spinal cord and total monitor units among three treatment plans: fVMAT(2 Full Arc), pVMAT(4 Partial Arc), and ncVMAT(2 Partial Arc + 2 Non-Coplanar Arc). All plans met the PTV criteria, showing uniform distribution. The average dose to the heart was 5.8 Gy for fVMAT, 6.97 Gy for pVMAT, and 7.6 Gy for ncVMAT, with the lowest value in fVMAT, which was statistically significant. However, the average lung dose was 9.01 Gy for fVMAT, 7.71 Gy for pVMAT, and 7.12 Gy for ncVMAT, with V_5Gy(%) values of 52.22%, 38.61%, 36.35% and V_10Gy(%) values of 37.8%, 27.33%, 24.15% respectively. ncVMAT showed the lowest values, while fVMAT had the highest, with statistical significance. In conclusion, ncVMAT effectively reduces lung radiation exposure in esophageal cancer radiotherapy, potentially reducing the incidence of side effects such as pneumonia. However, considering factors like setup accuracy and treatment time, applying an appropriate treatment plan may lead to better outcomes.

• Journal of Korea Foundry Society
• /
• v.44 no.1
• /
• pp.9-15
• /
• 2024

In this study, in order to improve the lifespan of parts made of manganese steel, manganese steel was cast by varying the amount of Ti added to the steel. In order to confirm the characteristics of the cast material, processing characteristics including tensile and surface characteristics and bearing ratio were investigated. It was confirmed that when the amount of Ti added to high manganese steel exceeds 0.5%, the strength of the alloy is improved due to grain refinement, and fine carbides are formed inside the steel. This results in increased resistance to surface wear compared to the alloy with only Mn added. There was no significant difference in the increase in tensile strength as the Ti content in manganese steel was increased. However, inclusion of Ti showed a small but greater effect on wear resistance compared to Mn, and the size and the distribution of carbides become coarse depending on the Ti content. and was evenly distributed. It was confirmed that the strength and surface properties of manganese steel can be improved by the addition of Ti to improve the lifespan of parts made with this steel. It was found that Ti is effective in developing materials with excellent wear resistance due to refinement of dendrite crystal grains. In the samples where Ti was added, the carbide appears to increase the resistance to surface roughness, and due to the nature of Mn steel, surface hardening begins to occur, which appears to extend the life.

• Horticultural Science & Technology
• /
• v.32 no.1
• /
• pp.10-17
• /
• 2014

This study was conducted to elucidate the relationship between light and coloring and to obtain basic results for promoting redness expression in 'Kalle' (Pyrus communis L.) pear skin. It was investigated in location of anthocyanin layer by microscopic observation and differences in skin color expression of 'Kalle' bagged with paper bag which has different light transmittance rate and inside temperature. However, there was no anthocyanin layer in the brown skin and golden yellow color, anthocyanin layer was distributed in epidermins or hyperdermis of red skin pear and apple. Dark red colored 'Kalle' had more anthocyanin content, $29.8mg{\cdot}100g^{-1}$ FW than light red colored apple 'Hongro'. Light transmittance rate of physical characteristics used paper bags was the highest in white paper bag, 42.2% and it also had more light quantity, $8.9{\mu}mol$ than any other tested paper bags in specific wave length 650-655 nm. The maximum temperature of inner bag was higher about $3^{\circ}C$ in yellow paper bag. The red coloration and anthocyanin contents in no bagged fruits were higher than in any other bagged fruit. However, red color expression among the bagged fruits was higher in white paper bag than in double layered black paper bag and yellow paper bag. Also, chromaticity value seemd to be a good index to explain variation of fruit skin color, because anthocyanin content and chromaticity value were higher. Based on these results, it is desirable to cultivate 'Kalle' without bag for stable redness expression but bagging is essential for decreasing damage by insect in Korea. Further examination to find suitable time of removing paperbag for redness expression and decreasing insect damage. In addition, it is required to develop paperbag whose transmittance rate is high in specific light wavelength or temperature of inner bags is low. Additional key words: anthocyanin, bagging, chromaticity value, light transmittance, Pyrus communis L.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.7
• /
• pp.914-920
• /
• 2008

In this study, hard roll breads were prepared with 3, 6, 9, 12, and 15% of concentrated sweet pumpkin powder (CSPP). The samples and a control were then compared in terms of quality characteristics, including pH, total titratable acidity, fermentation power of dough expansion, specific volume, baking loss, moisture content, color, textural characteristics, external and internal surface appearances, and sensory qualities of bread in order to determine the optimal ratio of CSPP in the formulation. As CSPP content increased, pH of dough, specific volume, baking loss, and lightness of bread decreased, while total titratable acidity of dough, pH, total titratable acidity, moisture content, and redness of bread increased. Fermentation power of dough expansion increased as incubation time increased. The CSPP samples had significantly higher yellowness, hardness, cohesiveness, gumminess, chewiness, and resilience than the control group. Adhesiveness was the highest at the 12% substitution level, while the lowest at the 6% level. Springiness increased with increasing CSPP content. In the sensory evaluation, as CSPP content increased, scores for color and consistency of crumb decreased, while scores for aroma of sweet pumpkin, sweetness, and delicious taste increased. Density of crumb pore were maximal with the 12% CSPP substitution. The CSPP samples had significantly higher uniformity of crumb pore and springiness of crumb than the control group. However, mouth-feel and overall acceptability showed the reverse effect, obtaining fairly good scores. In conclusion, the results indicate that substituting $6{\sim}9%$ CSPP to hard roll bread is optimal, providing good physiological properties as well as reasonably high overall acceptability.