• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.708-715
• /
• 2017

Recently, in order to meet the stricter emission regulations, the proportion of after-treatments for vehicles and vessels has been increasing gradually. The objective of this study is to investigate the improvement of $CH_4$ reduction ability of natural gas oxidation catalyst (NGOC), which reduces toxic gases emitted from CNG buses. Thirteen NGOCs were prepared, and the conversion performance of noxious gases according to the type of supports, the loading amount of noble metal, and surfactant and aging were determined. Support Zeolite supported on No. 3 $NGOC(1Pt-1Pd-3MgO-3CeO_2/(46TiO_2+23Al_2O_3+23Zeolite)$ is an anionic alkali metal/earth metal component that improved the oxidation reactivity between CO and NO and noble metal dispersion, and thus enhanced the $CH_4$ reduction ability. As the loading amount of Pd, a noble metal with a high selectivity to $CH_4$, was increased, the number of reaction sites was increased and the ability to reduce $CH_4$ was improved. No. 11 $NGOC(1Pt-1Pd-3MgO-3CeO_2/(Z20+Al80)$(pH=8.5), to which nitrate surfactant had been added, exhibited well dispersed catalyst particles with no agglomeration and improved the $CH_4$ reduction ability by 5-15%. The $NGOC(2Pt-2Pd-3Cr-3MgO/90Al_2O_3)$(48h aging), which was mildly thermal aged for 48h, increased the $CH_4$ reduction ability to about 10% or less as compared with No. 12 NGOC(Fresh).

• Composites Research
• /
• v.32 no.6
• /
• pp.355-359
• /
• 2019

The high efficient water splitting system should involve the reduction of high overpotential value, which was enhanced by the electrocatalytic reaction efficiency of catalysts, during the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) reaction, respectively. Among them, transition metal-based compounds (oxides, sulfides, phosphides, and nitrides) are attracting attention as catalyst materials to replace noble metals that are currently commercially available. Herein, we synthesized optimal monodisperse Co₃[Co(CN)₆]₂ PBAs by FESEM, and confirmed crystallinity by XRD and FT-IR, and thermal behavior of PBAs via TG-DTA. Also, we synthesized monodispersed Co₃O₄ nanocubes by calcination of Co₃[Co(CN)₆]₂ PBAs, confirmed the crystallinity by XRD, and proceeded OER measurement. Finally, the synthesized Co₃O₄ nanocubes showed a low overpotential of 312 mV at a current density of 10 mA·cm^-2 with a low Tafel plot (96.6 mV·dec^-1).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.5
• /
• pp.196-201
• /
• 2023

In order to improve the efficiency of the water splitting system for hydrogen energy production, the high overvoltage in the electrochemical reaction caused by the catalyst in the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) must be reduced. Among them, transition metal-based compounds (hydroxide, sulfide, etc.) are attracting attention as catalyst materials to replace currently used precious metals such as platinum. In this study, Ni foam, an inexpensive metal porous material, was used as a support and β-Ni(OH)₂ microcrystals were synthesized through a hydrothermal synthesis process. In addition, changes in the crystal morphology, crystal structure, and water splitting characteristics of β-Ni(OH)₂ microcrystals synthesized by doping Fe to improve electrochemical properties were observed, and applicability as a catalyst in a commercial water electrolysis system was examined.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.1
• /
• pp.30-35
• /
• 2024

In order to improve the efficiency of the water splitting system for hydrogen production, the high overvoltage in the electrochemical reaction caused by the catalyst in the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) must be reduced. Among them, transition metal-based compounds are attracting attention as catalyst materials that can replace precious metals such as platinum that are currently used. In this study, nickel foam, an inexpensive metal porous material, was used as a support, and Fe-doped β-Ni(OH)₂ microcrystals were synthesized through a hydrothermal synthesis process. In addition, in order to improve OER properties, changes in the shape, crystal structure, and water splitting characteristics of Fe-Mo co-doped β-Ni(OH)₂ microcrystals synthesized by co-doping with Mo were observed. The changes in the shape, crystal structure, and applicability as a catalyst for water splitting were examined.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.134-134
• /
• 2003

SnO$_2$를 모물질로 하는 가스센서는 n형 산화물 반도체로서 공기중의 산소의 흡탈착 및 전자의 수수에 의해 전기전도도의 변화로 특정 가스를 감지한다. 지금까지 반도체식 가스센서의 모물질로 가장 많이 연구되어 왔지만 아직도 선택성, 안정성 등 여러 가지 문제를 안고 있다. 그리고 개선방안으로 귀금속 촉매의 첨가 및 입자의 크기의 조절 등이 흔히 연구되어 왔다. 따라서 본 연구에서는 순수한 SnO$_2$ 를 이용하여 소결 온도 및 입자 크기에 의한 영향을 CO가스 및 수분에 대한 감도, 반응 시간을 통해 알아보았다. 수열 합성 및 침전 법으로 나노 크기의 SnO$_2$ 분말을 합성하여 스크린 인쇄법으로 후막 가스센서를 제조하였다 침전법에서 SnCl$_4$에 암모니아수로 pH=10.5로 적정하여 SnO$_2$ 분말을 얻었다. 그리고 입자 크기를 조절하기 위해 수열 합성 시 autoclave 내의 수열처리 온도를 100, 150, 20$0^{\circ}C$로 조절하여 SnO$_2$ 분말을 제조하고 입자 크기와 성분분석을 위해 XRD, SEM, TEM, BET 측정을 하였다. 그 결과 침전법으로 제조한 입자의 크기는 20nm 정도였으며 수열 처리한 SnO$_2$ 입자는 10nm이하의 미세한 입자를 얻을 수 있었다. 수열 합성 시 온도가 높아질수록 더 작은 입자 크기를 얻을 수 있었고 600, 7()0, 80$0^{\circ}C$ 열처리 후 입자성장이 침전법에 의한 SnO$_2$ 분말보다 더 작게 일어났다. 이렇게 제조한 나노크기의 SnO$_2$ 분말을 이용하여 습도 및 CO 가스에 대한 그 특실을 평가하였다. CO 20ppm에 대하여 40%정도의 감도를 보였으며 입자가 작아질수록 높은 감도를 보이는 것을 확인 할 수 있었다. 반면 CO 가스와 반응 후 회복 시 입자 의기가 작아질수록 회복이 늦어짐을 알 수 있었다. 그리고 15$0^{\circ}C$에서 습도에 대한 반응 후 회복시간을 조사해보니 같은 결과를 얻을 수 있었다. 이것은 입자 필기가 작아질수록 많은 흡착 사이트를 제공함으로써 높은 감도를 가지지만 반면 다량의 흡착된 가스들이 탈착 하는데 더 많은 시간이 소요되었기 때문이다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.1
• /
• pp.10-17
• /
• 2008

This study has been focused on the partial oxidation(POX) of n-octane over Rh-containing catalysts supported on alumina. The catalysts for this reaction were prepared by incipient wetness(IW) and co-gel(CG) methods, followed by the calcination at $900{\circ}C$ or $1,200{\circ}C$. When applied to the POX of n-octane carried out at $600{\circ}C$ with C/O=3 and GHSV=3,450/h, the catalyst prepared by the CG method and calcined at $1,200{\circ}C$ showed the best activity, yielding 42% syngas($H_2$+CO) with the $H_2$/CO ratio of $2{\sim}2.4$. To enhance the activity and stability of catalysts, bimetallic catalysts were synthesized by the CG method. As a result, the performance of Rh-Ni/$Al_2O_3$ catalyst was superior to that of Rh/$Al_2O_3$ catalyst in terms of the catalyst stability, due to the retarding effect on the Rh-to-$Rh_2O_3$ transition by the addition of Ni. This result was confirmed by XRD, TEM, and TPR characterizations.

• Journal of Sensor Science and Technology
• /
• v.8 no.4
• /
• pp.327-332
• /
• 1999

Catalytic combustion type gas sensors were fabricated by using noble metal(Pt and Pd) added ${\gamma}-Al_2O_3$ powder with specific surface area of $200\;m^2/g$. The fabricated sensor showed power consumption of 500 mW at the operating voltage of 1.75 V and high sensitivity of about 120 mV for butane, methane, or propane 100%LEL, respectively. The sensor properties also showed good linearity to hydrocarbon gas concentration variation, reproductivity and stability for relative humidity variation. And it showed high stability in butane ambient for 100 days.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.96-96
• /
• 2016

나노섬유(nanofiber), 나노선(nanowire), 그리고 나노튜브(nanotube)와 같은 1차원 구조의(one-dimensional structure) 나노재료는 벌크(bulk) 및 박막(film) 재료와는 다르게 물리적, 화학적으로 특이한 성질을 가지고 있으며, 이러한 성질은 나노재료의 구조, 형상, 크기 등에 큰 영향을 받는다. 첫 째, 전기방사(electrospinning) 공정을 이용한 나노섬유의 합성; 용액의 특성, 전기장 세기, 방사시간 등의 변수를 조절하게 되면 방출되는 재료의 형상을 입자 혹은 섬유상의 형태로 얻을 수 있으며, 전기방사를 통해 합성된 나노재료의 소결 온도 및 시간을 달리함으로써 나노입자의 크기를 조절할 수 있다. 또한, 템플레이트 합성법(template synthesis) 및 이중노즐(coaxial nozzle)을 이용해 속이 빈 형태인 중공(hollow) 구조의 나노섬유를 얻을 수 있으며, 전기방사에 사용되는 전구물질에 원하는 금속 및 산화물을 첨가함으로써 복합체(composite) 나노섬유를 얻을 수 있다. 둘 째, VLS(Vapor-Liquid-Solid) 공정을 이용한 나노선의 성장; 온도, 압력, 전구물질의 양, 그리고 시간 등의 변수를 조절하게 되면 원하는 직경 및 길이를 갖는 나노선을 성장시킬 수 있다. 그리고 ALD(Atomic Layer Deposition)를 이용해 나노선에 추가적인 층을 형성함으로써 코어-셀 구조를 형성할 수 있으며, 감마선, UV와 같은 공정을 이용해 귀금속 촉매를 나노선에 기능화 시킬 수도 있다. 코어-셀 구조를 갖는 나노선/나노섬유는 코어 혹은 셀 층의 전자나 홀의 이동을 유발하여 전자공핍층(electron depletion layer) 또는 정공축적층(hole accumulation layer)을 확대 및 축소시켜 센서의 초기저항을 증가시키거나 감소시키는 역할로써 이용되고 있으며, 특히, 셀 층의 두께가 셀 층 재료의 Debye length와 유사한 크기를 갖게 되면, 셀 층은 완전공핍층(fully depleted layer)을 형성해 최대의 감도를 나타낼 수 있다. 본 연구에서는 다양한 제조 공정을 통해 제작될 수 있는 1차원 나노-구조물을 가스센서에 적용하는 사례들을 소개하고, 이러한 가스센서의 감응성능을 향상시키기 위한 방법의 한 가지로 원자층증착법으로 나노선/나노섬유의 표면에 셀층을 형성하여 감응성 향상 메커니즘 및 관련 주요 변수들을 조사하고자 한다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.6
• /
• pp.587-593
• /
• 2023

This research project focused on the production of hydrogen through ammonia decomposition reactions while investigating how the reactivity of this process varies when employing different catalysts. Several metal oxide supports (Al₂O₃, La₂O₃, CeO₂) were utilized as catalysts, with active metals from both the transition metal group (Co, Ni, Fe, Cr, Cu) and the noble metal group (Ru, Rh, Pd, Pt) impregnated onto these supports. Furthermore, the study examined how the reactivity evolves with changes in reaction temperature when employing the prepared catalysts. Additionally, the research delved into the distinctive activation energies associated with each of the catalysts. In this research, In the noble metal catalyst system, the order of high activity for ammonia decomposition reaction to produce hydrogen is Ru > Rh > Pt ≈ Pd. In the transition metal catalyst system, the order of high activity is Co > Ni > Fe > Cr > Cu.