• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.3
• /
• pp.125-131
• /
• 2007

Electric motor efficient improvement from home appliance field is important to the effect reducing the energy consumption. But the electric motor design/analysis technology is still insufficient. Specially the electric motor design/analysis technology of satisfying characteristic of both the induction motor and the synchronous motor such as Line start permanent motor. Therefore the electric motor design/analysis technology is urgently demanded reliability. This paper proposes the sing1e-phase line-start permanent magnet motor to develop the motor it with be able to alternate the sing-phase induction motor it is a refrigerator compressor motor. The sing-phase induction motor is analyzed in the steady state. And we have a certification test to compare our single-phase line-start permanent magnet motor with the sing-phase induction motor. In order to improve the performance, the stator of the single-phase line-start permanent magnet motor is same as the stator of the sing-phase induction motor and changes the rotor form and has the permanent magnet. It used the Finite Element Method(FEM) which is widely used with electronic-magnetic field numerical analysis method.

• Journal of the Korean Magnetics Society
• /
• v.20 no.3
• /
• pp.94-99
• /
• 2010

Minor B-H loop measurement for a rectangular high tensile steel was obtained by using Labview. A ferrite cores of high permeance with primary and secondary windings on the steel plate were used to form a closed loop of magnetic flux. To compensate errors due to an extremely small gap between a pair of ferrite core, and between the ferrite core and the rectangular high tensile steel, quadratic function of least square method was used. Also a 3D FEM magnetic analysis tool was used to measure H and B of the steel. B-H loop of the high tensile steel plate can be measured up to 520 A/m of a magnetic field and 0.15 T of a magnetic flux density.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.112-118
• /
• 2004

Recently, development of rare earth permanent magnet with the high remanence, high coercivity allows the design of brushless motors with very high efficiency over a wide speed range. Cogging torque is produced in a permanent magnet by magnetic attraction between the rotor mounted permanent magnet and the stator teeth. It is an undesired effect that contributes to output ripple, vibration, and noise of machine. This cogging torque can be reduced by variation of magnet arc length, airgap length, magnet thickness, shifting the magnetic pole and varying the radial shoe depth and etc. In this paper, some airgap length and magnet arc that reduce cogging torque are found by finite element method(FEM) and Maxwell stress tensor method. The SPM(Surface Permanent Magnet) type of high-power Brushless DC (BLDC) motor is optimized as a sample model.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.7
• /
• pp.29-38
• /
• 2018

Three-dimensional continuum modeling of dynamic soil-pile-structure interaction embedded in a liquefiable sand was carried out. Finn model which can model liquefaction behavior using effective stress method was adopted to simulate development of pore water pressure according to shear deformation of soil directly in real time. Finn model was incorporated into Non-linear elastic, Mohr-Coulomb plastic model. Calibration of proposed modeling method was performed by comparing the results with those of the centrifuge tests performed by Wilson (1998). Excess pore pressure ratio, pile bending moment, pile head displacement-time history according to depth calculated by numerical analysis agreed reasonably well with the test results. Validation of the proposed modeling method was later performed using another test case, and good agreement between the computed and measured values was observed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.12
• /
• pp.1077-1085
• /
• 2016

Linear roller bearing (LRB) is an important mechanical element that is widely used in precise positioning systems that are subjected to large loads. This paper presents a new model for estimating the displacement of an LRB subjected to external forces. For this purpose, assuming that the linear motion block (LM block) is rigid, the equilibrium conditions for the LRB were obtained by solving the equilibrium equations of the rollers and the rigid LM block using the iterative Newton-Raphson method. The contact loads between the rollers and raceways were determined considering the profiled rollers. Then, the structural deformations of the LM block, subjected to the contact loads from the rigid LM block model, were computed using a finite element model for the LM block. The displacements of the LRB were then determined by superposition of the rigid LM block displacements on the induced displacements due to the structural deformations of the LM block. The proposed method was verified through comparison with a program by the bearing manufacturer.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.8
• /
• pp.1743-1750
• /
• 2003

DC motor requires a rotor speed sensor for accurate speed control. The speed sensors such as resolvers and encoders are used as a speed detector, but they increase cost and size of the motor and restrict the industrial drive applications. So in these days, many papers have reported in the sensorless operation of DC motor〔3­5〕. This paper presents a new sensorless strategy using neural networks〔6­8〕. Neural network has three layers which are input layer, hidden layer and output layer. The optimal neural network structure was tracked down by trial and error, and it was found that 4­16­1 neural network structure has given suitable results for the instantaneous rotor speed. Also, learning method is very important in neural network. Supervised learning methods〔8〕 are typically used to train the neural network for learning the input/output pattern presented. The back­propagation technique adjusts the neural network weights during training. The rotor speed is gained by weights and four inputs to the neural network. The experimental results were found satisfactory in both the independency on machine parameters and the insensitivity to the load condition.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.1
• /
• pp.33-40
• /
• 2008

This paper proposes a sensorless drive method that estimates the rotor position by analysing Back EMF of single-phase Switched Reluctance motor (SRM). The rotor position information is necessary required, because SRM's torque is generated by exciting a stator winding according to rotor position. In order to detect the position of the rotor, the various rotor position sensors have been used. However, most of the position sensors not only increase the construction cost and the volume of the motor but also decrease reliability of driving system with environment. This paper proposed the method using the Back EMF to solve such problems. When a rotor and stator are overlapped, the Back EMF is sharply changed. By detecting this point, the rotor position can be estimated. Thus SRM is driven by turn on and turn off switches at the proper position through speed calculation. The validity of proposed method is verified through simulation and experiment.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.5
• /
• pp.223-229
• /
• 2023

This Paper propose the method that measure main system parameters for PI(proportional-integral) current control of a.c. motor adopting the vector control technique. For current control, the PI control input is could be tuning by several selective methods. Among the several methods, the method that using the main system parameters, wire resistance and inductance, are frequently used. In this study, the technique to dissect and measure these two system parameters through the results of simple feedback control. This analytic measurement method is measuring parameters step by step dissecting the results of P control using simple proportional feedback gain about the unit step or multiple step reference command. This strategy is an real time analytic measurement method that calculate current control gains of torque component and flux component both for vector control of A.C. motor without introducing the further measurement circuits and complex measuring algorithms.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.2
• /
• pp.105-112
• /
• 2005

The electrolytic reduction of uranium oxide in a LiCl-Li$_{2}$O molten salt system has been studied in a 10 g U$_{3}$O$_{8}$ /batch-scale experimental apparatus with an integrated cathode assembly at 650$^{\circ}C$. The integrated cathode assembly consists of an electric conductor, the uranium oxide to be reduced and the membrane for loading the uranium oxide. From the cyclic voltammograms for the LiCl-3 wt$\%$ Li$_{2}$O system and the U$_{3}$O$_{8}$-LiCl-3 wt$\%$ Li$_{2}$O system according to the materials of the membrane in the cathode assembly, the mechanisms of the predominant reduction reactions in the electrolytic reactor cell were to be understood; direct and indirect electrolytic reduction of uranium oxide. Direct and indirect electrolytic reductions have been performed with the integrated cathode assembly. Using the 325-mesh stainless steel screen the uranium oxide failed to be reduced to uranium metal by a direct and indirect electrolytic reduction because of a low current efficiency and with the porous magnesia membrane the uranium oxide was reduced successfully to uranium metal by an indirect electrolytic reduction because of a high current efficiency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.230-230
• /
• 2007

전력선 통신(Power Line Communication)은 최근 전력선을 이용한 통신기술의 발달과 더불어 세계적으로 관심도가 높아지고 연구 개발 및 자본 투자가 활발히 진행되고 있으며, 안정적인 네트워크를 구성하기 위해서는 고주파 전력선 통신 신호를 차단하는 블로킹 필터가 반드시 적용되어야 한다. 전력선 통신용 블로킹 필터는 광대역의 주파수 특성과 높은 신호감쇄 특성 및 대전류 특성이 요구되며, 이러한 특성을 구현하기 위해서는 블로킹 필터의 핵심부품인 자심재료의 고투자율 및 대전류화가 이루어져야 한다. 따라서 본 연구에서는 우수한 전 자기적 특성이 균일하게 유지되고, 전력선에 흐르는 대전류에 의한 자심재료의 포화가 발생하지 않도륵 새로운 자심 재료를 설계하여, 전력선 통신을 적용한 홈 네트워크 구축의 핵심 부품인 광대역 블로킹 필터를 개발하고자 하였다. 2350과 0.3 T의 투자율과 포화자속 밀도를 갖는 EI 형상의 자심재료를 해석모델로 설정하고 다중 에어 갭의 위치에 따른 전류와 자속밀도 변화를 유한요소 해석법으로 분석한 결과 자심재료의 대전류 특성에 지배적인 영향을 미치는 에어 캡의 삽입 위치를 알 수 있었고, 새로운 해석 모델인 I 형상의 로드(ROD) 코어에 대해 수치해석을 수행하여, 100A의 통전 전류에서도 자기적으로 포화되지 않고 인덕턴스의 정밀 제어가 가능하고, 특성의 신뢰성과 대전류에 대한 안정성을 증가시킬 수 있는 인덕터를 설계하였다. 또한 수동소자를 이용한 LC 공진회로를 기본 구성으로 하고, 주파수 대역, 신호 감쇄율과 대전류 특성, 상용화를 고려하여 블로킹 필터 회로를 설계하였으며, 유한요소해석법을 적용한 전자장 모의해석을 통하여 최소의 크기를 갖는 I 형상의 자심재료에 $6{\Phi}$의 에나멜 동선을 6.5턴, 6턴 권선하여 2.5, $2.15\;{\mu}H$의 인덕턴스를 갖는 직렬 인덕터를 구현하였고 블로킹 필터를 구성하였다. 주파수에 따른 신호감쇄 특성을 5 Hz~1 MHz의 주파수 범위에서 측정한 결과 약 490 kHz~450 kHz의 주파수 대역에서 -70dB의 신호감쇄 특성을 나타냈다. 본 연구를 통해 개발된 100A급 광대역 블로킹 필터가 적용되어 상용화 될 수 있을 것으로 판단되며, 또한 모뎀 통신 주파수 대역에서 -70dB 이상의 높은 감쇄 특성을 갖기 때문에 신호차단 특성이 보다 우수할 것으로 사료된다.