• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4C
• /
• pp.117-125
• /
• 2011

The practical use of the electrical resistivity, which can makes the acquirement of the high resolution data in specific area, is increased in order to obtain a reasonable data for a ground investigation. The objective of this study is development of TRPF(Temperature-compensated Resistivity Probe for Field test), and an application in the field test for obtaining a reliable electrical resistivity value about considering the temperature effects. Temperature sensor is attached at 15mm, 30mm, 90mm below from the cone tip in consideration with the results of temperature transient process of cone probe and safety, and the angle of cone tip is $60^{\circ}$ for geometrical reason and minimizing the disturbance during the penetration test. Diameter of the cone probe is equally 35.7mm and penetration rate is 2 cm/sec for a comparison with standard cones such as CPT and SPT, and others. The temperature change is instantly observed around $4^{\circ}C$ when touching the ground, and the comparing results among the other cones indicates that the temperature compensation should be conducted in the ground survey using the electrical resistivity. This study shows that the necessity of temperature effects compensation during penetration test through the development and field verification of TRPF (Temperature-compensated Resistivity Probe for Field test).

• Journal of the Mineralogical Society of Korea
• /
• v.16 no.1
• /
• pp.91-106
• /
• 2003

XRD results on annealing studies of Na-feldspars (Amelia albite) show rapid changes in the lattice parameters of the $1073^{\circ}C$-heated samples owing to disordering of Al and Si as well as lattice distortions upon quenching of the heated specimens. While a low albite transformed to a high albite by 7-days annealing at $1073^{\circ}C$, it remains as an early intermediate albite even by 140-days annealing at $924^{\circ}C$ due to the slower Al-Si disordering rate. From the heated samples tweed structures of $100∼200\AA$ were typically observed by TEM, which showed different ways of development between the $1073^{\circ}C$ -heated one and the $923 ^{\circ}C$ -heated one. The former locally trans-farmed to rnicrostructures similar to albite twin, while the latter transformed to domain structures containing albite twin plane in the wider area. The origin of tweed structures is suggested to be formation of incipient twins (albite twin and pericline twin) to reduce the lattice instability which is increased by disordering of Al and Si as well as quenching.

• The KIPS Transactions:PartB
• /
• v.11B no.1
• /
• pp.27-34
• /
• 2004

This paper proposes a method to trace and interpret a moving object based on the information which can be directly obtained from MPEG-2 compressed video stream without decoding process. In the proposed method, the motion flow is constructed from the motion vectors included in compressed video. We calculate the amount of pan, tilt, and zoom associated with camera operations using generalized Hough transform. The local object motion can be extracted from the motion flow after the compensation with the parameters related to the global camera motion. Initially, a moving object to be traced is designated by user via bounding box. After then automatic tracking Is performed based on the accumulated motion flows according to the area contributions. Also, in order to reduce the cumulative tracking error, the object area is reshaped in the first I-frame of a GOP by matching the DCT coefficients. The proposed method can improve the computation speed because the information can be directly obtained from the MPEG-2 compressed video, but the object boundary is limited by macro-blocks rather than pixels. Also, the proposed method is proper for approximate object tracking rather than accurate tracing of an object because of limited information available in the compressed video data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.112-118
• /
• 2018

In order to meet the strict emission regulations for internal combustion engines based on fossil fuel, the proportion of after-treatments for vehicles and vessels is gradually increasing. Diesel engines have high power, good fuel economy, and lower $CO_2$ emissions, and their market shares are increasing in commercial vehicles and passenger cars. However, NOx is generated in the localized high-temperature combustion regions, and particulate matter is formed in the zones of diffusion combustion. LNT and urea-SCR catalysts have been developed for after-treatment of the exhaust gas to reduce NOx in diesel vehicles. This study aims to improve the NOx reduction performance of Cu SCR catalyst, which is widely used in light, medium, and heavy-duty diesel engines. The de-NOx performance of $5Cu-2ZrO_2$/93Zeolyst(Si/Al=13.7) SCR catalyst was about 5-50% higher than that of $5Cu-2ZrO_2$/93Zeolite(Si/Al=2.9) at catalyst temperatures of $300^{\circ}C$ or higher. The zeolite had lower metal dispersion than zeolyst, and the reaction rate of the catalyst decreased as the average particle size increased. The $10Cu-2ZrO_2$/88Zeolyst catalyst loaded with 10wt% Cu had the highest NOx conversion rate of 40% at $200^{\circ}C$ and about 65% at $350^{\circ}C$. The ion exchange rate of Cu ions increased with that of Al, the crystalline compound of zeolite, and the de-NOx performance was improved by 20-40% compared to other catalysts.

• Journal of KIISE:Software and Applications
• /
• v.37 no.2
• /
• pp.104-109
• /
• 2010

The lighting reflection is a common problem in image analysis and causes the many difficulties to extract distinct features in related fields. Furthermore, the problem grows in the rainy night. In this paper, we aim to remove light reflection effects and reconstruct a road surface without lighting reflections in order to extract distinct features. The proposed method utilizes a 3D analysis based on a multiple geometry using captured images, with which we can combine each reflected areas; that is, we can remove lighting reflection effects and reconstruct the surface. At first, the regions of lighting sources and reflected surfaces are extracted by local maxima based on vertically projected intensity-histograms. After that, a fundamental matrix and homography matrix among multiple images are calculated by corresponding points in each image. Finally, we combine each surface by selecting minimum value among multiple images and replace it on a target image. The proposed method can reduces lighting reflection effects and the property on the surface is not lost. While the experimental results with collected data shows plausible performance comparing to the speed, reflection-overlapping areas which can not be reconstructed remain in the result. In order to solve this problem, a new reflection model needs to be constructed.

• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.62-68
• /
• 2000

Ultra thin TiN films (50∼700nm thickness) were deposited on AISI 304 stainless steel substrates using a reactive DC magnetron sputtering deposition process to investigate their wear and friction properties. Dry sliding wear tests of the films were carried out against hardened steel and alumina counterparts using a pin-on-disk type wear tester at room temperature. Variation of friction coefficient was measured as a function of film thickness, load, sliding speed and roughness of the substrate. Worn surfaces of the film were examined by a scanning electron microscope. Wear resistance of the TiN film increased with the increase of the film thickness. The TiN film showed relatively high wear resistance in spite of its ultra thin thickness when it is mated by the steel counterpart, while it showed poor wear resistance with the alumina counterpart. The good wear resistance with the steel counterpart was explained by the formation of oxide layers on the film surface and sound interface character between the ultra thin film and the substrate.

• Journal of the Korea Concrete Institute
• /
• v.25 no.1
• /
• pp.99-106
• /
• 2013

Concrete materials subjected to impact by high velocity projectiles exhibit responses that differ from those when they are under static loading. Projectiles generate localized effects characterized by penetration of front, spalling of rear and perforation as well as more widespread crack propagation. The magnitude of damage depends on a variety of factors such as material properties of the projectile, impact velocity, the mass and geometry as well as the material properties of concrete specimen size and thickness, reinforcement materials type and method of the concrete target. In this study, penetration depth of front, spalling thickness of rear and effect of spalling suppression of concrete by fiber reinforcement was evaluated according to compressive strength of concrete. As a result, it was similar to results of the modified NDRC formula and US ACE formula that the more compressive strength is increased, the penetration depth of front is suppressed. On the other hand, the increase in compressive strength of concrete does not affect spalling of rear suppression. Spalling of rear is controlled by the increase of flexural, tensile strength and deformation capacity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.877-885
• /
• 2013

A seawater pipe of the engine room in the ships is being surrounded with severely corrosive environments caused by fast flowing of the seawater, containing aggressive chloride ion and high conductivity etc.. Therefore, the leakage of the seawater from its pipe have been often occurred due to its local corrosion by aggressive chloride ions. Subsequently, its leakage area is usually welded by AC shielded metal arc welding with various electrodes. In this study, when the sea water pipe is welded with several types of electrodes such as E4301, E4311, E4313 and E4316, a difference of the corrosion resistance on the welding metal zones was investigated using an electrochemical method, observing microstructure, measuring polarization behaviors and hardness. The weld metal zone welded with E4313 electrode exhibited the lowest value of hardness compared to other weld metal zones. In addition, its zone indicated also the best corrosion resistance than those of other weld metal zones. Furthermore, all of the weld metal zones revealed a relatively better corrosion resistance than those of the base metal zones. and also showed higher hardness than the base metal zones.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.47-47
• /
• 2011

하도 내 수역이 식생으로의 천이가 진행되고 최종적으로는 육상 식물들이 활착하게 되는 육역화 현상은 하도의 수리학적 문제 및 환경생태적 측면에서 큰 문제를 발생시킬 가능성을 내포하고 있다. 최근 하천복원의 필요성이 강조됨에 따라 물골공법 및 국부세굴 유도형 공법 등 실용성을 포함시킨 다양한 하천 복원공법이 제시되고 있다. 물골공법은 자연적인 물골형상에 의한 유사퇴적방지, 홍수시 유속저감 및 생물서식처를 조성하는 하상 생태복원 공법을 의미하며, 본 연구에서는 수리모형실험 및 3차원 수치모의를 이용하여 다양한 하도육역화 방지 공법 중 물골공법의 효과 및 적용성을 검토하였다. 물골공법의 특성 중 유사퇴적방지의 효율성 분석을 위해 부정류(unsteady state)상태에 대해 연구를 수행하였으며 홍수 이후 수위하강시 고수부지 및 물골 주변에서의 흐름특성을 재현하였다. 수위하강 모의를 위해 임의의 수위하강시간을 선정하여, 수위하강이 진행되는 시간( )을 각각의 수위하강시간으로 무차원 화한 후 무차원된 시간(t/�� )에 따른 흐름특성을 비교 분석하였으며 모의 및 분석결과, 수위하강시간이 80초 이상일 경우 주요 지점에서의 유속의 변화는 무차원된 시간에 대하여 일치하였으며 수리모형실험 및 수치모의에 적용할 수위하강시간으로 선정할 수 있었다. 물골 전구간에 대한 부정류 실험을 위해 LSPIV(Large-Scale Particle Image Velocimetry)장치를 이용하여 수위하강에 따른 물골주변의 흐름특성을 관측하였으며 3차원 수치모의를 통해 검증하였다. 실험 분석결과, 수위하강에 따라 고수부지 위로 흐르는 유수가 물골 내부로 유입되어 물골을 따라 흘러 물골 합류부로 이동하는 것으로 나타났으며, 이는 홍수시 유수와 함께 떠다니는 부유사(suspended load)가 물골로 유입되어 물골 합류부로 이동하므로 물골의 유사배제 가능성을 판단할 수 있었다. 또한 물골의 유사배제능력을 평가를 위해 실험을 통하여 산정된 최대 및 최소 마찰속도(U )와 유사이동 한계곡선을 이용하여 물골의 통한 배제 가능한 유사의 입경을 분석하였다. 분석결과, 최소 2mm에서 최대 4mm로 나타났으며 이 입경 이하인 유사에 대해서는 퇴적되지 않고 물골을 통하여 배제될 수 있을 것으로 예상되었다. 본 연구 결과 물골공법 적용시 수위하강에 따라 물골에서 하도방향으로 유사의 수세(flushing)효과가 나타났으며 유사의 부상 및 이송이 효과적으로 발생하여 고수부지 내 유사퇴적 방지가 효과적인 것으로 판단되었다. 추후 다양한 형상의 물골에 대한 능력검토가 보완된다면 물골설계지침 제안을 위한 자료로 활용 가능할 것이다.

• Korean Journal of Materials Research
• /
• v.9 no.8
• /
• pp.804-809
• /
• 1999

Silica films were prepared on Si single crystal substrates by a sol-gel process without DMF using TEOS as a starting material. Films were fabricated by spin coating technique. For films having a composition of TEOS : HCI(1:0.05mol), gelation time, the thickness of films, the formation of cracks and the microstructure of the films were investigated as a function of the molar ratio of $CH_3OH and H_2O$. With 8mol $CH_3OH$, the longest gelation time was measured to be 640hr. The thickness of the coated films was decreased with increasing content of $CH_3OH$. The films were sintered at $500^{\circ}C$ for 1hr with a heating rate of $0.6^{\circ}C$/min. The coated films showed worm-like grains and partially cracked microstructures at an amount of $CH_3OH$ 2mol and 4mol. The addition of more than 8 mole of $CH_2OH$ resulted in crack-free silica films. This suggests that crack-free films can be fabricated by controlling the surface tension energy of the sol solutions without DMF.