• Geophysics and Geophysical Exploration
• /
• v.7 no.3
• /
• pp.197-206
• /
• 2004

Because the minute displacement of ground accompanied by excessive pumping of groundwater at specified site is mainly generated from ill-balancing of water budget within groundwater basin, It is necessary to monitor the variation of micro-subsidence for a long time at representative points. We made up the conceptual model using two-dimensional electrical resistivity survey and three-dimensional soil profile consisted of loam and sand. In verifying the reliability of this conceptual model using numerical modeling for ground settlement and groundwater flowing, two-dimensional electrical resistivity survey with short distance of electrode following soil sampling with hand auger would be useful for interpreting hydrogeological structure related to the minute displacement of ground consisted of loam and sand.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.1057-1060
• /
• 2008

For high performance concrete, due to its low water cement ratio (water binder ratio) and addition of mineral admixtures, pretty high autogenous shrinkage and thermal deformation occur at very early age of casting (especially before hardening). This may lead to early age cracking of HPC structures, and then may influence the durability of HPC. This paper has monitored the early age properties of HPC successfully by embedded FBG strain sensor. The results showed that the deformation increased rapidly within the first day after HPC casting. And its value is up to $85{\mu}{\varepsilon}$, which is the 30% of two-month deformation ($280{\mu}{\varepsilon}$). Considering the durability and permeability of HPC, the first-day deformation is pretty high and can not be neglected. Also the superior capability of FBG sensors such as continuity, stability and multiplexed technique etc, has been demonstrated.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.2
• /
• pp.87-94
• /
• 2012

A damage estimation method of wind turbine tower using natural frequency and mode shape is presented for effective condition monitoring. Dynamic analysis for a wind turbine was carried out to obtain the response of tower from which modal properties were identified. A neural network was learned based on training patterns generated by the changes of natural frequency and mode shape due to various damages. The changes of modal property were calculated using a program for modal parameter estimation. Damage locations and severities could be successfully estimated for 10 damage cases including multi-damage cases using the trained neural network. The damage severities for very small damages generally tends to be slightly under-estimated however, the identified damage locations agreed reasonably well with the accurate locations. Enhancement of the estimation result for very small damage and verification of the proposed method through experiment will be carried out by further study.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.2
• /
• pp.58-65
• /
• 2021

As increasing social needs of pavement maintenance, pattern frame method has been constructed in Korea. The pattern frame not only increases the skid resistance of pavements but also improve the scenery. However, construction of the pattern frame currently relies on imported materials. In this paper, we localize the materials used in pattern frame and conduct performance verification on them. The important performance indicators are the adhesion strength of undercoating materials and the skid resistance of finished pattern frames. The adhesion strength was targeted at 1.4MPa, and the localization alternative material met the target performance with 2.35MPa, the skid resistance performance was targeted at 40BPN, and the localization alternative material met the target performance with 75BPN. In the case of localized materials, approximately 40% cost reduction (per 1m²)compared to imported materials was confirmed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.2
• /
• pp.121-130
• /
• 2008

Recently, we can see an increasing amount of dam damage or failure due to aging, earthquakes occurrence and unusual changes in weather. For this reason, dam safety is gaining more importance than ever before in terms of disaster management at a national level. Therefore, the government is trying to come up with an array of legal actions to secure consistent dam safety. Other dam management organizations are also taking various institutional and technical measures for the same purpose. In this study, Dam Safety Management System, KDSMS, has developed for consistent and efficient dam safety management. The KDSMS consists of dam and reservoir data, a hydrological information system, a field inspection and data management system, a instrumentation and monitoring system including earthquake monitoring, a field investigation and safety evaluation system, and a collective information system. The KDSMS is a kind of enterprise management system which has been developed to deal with safety management of each field, research center, and headquarter office and their correlation as well as detailed safety information management.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.2
• /
• pp.53-60
• /
• 2024

Prestressed concrete (PSC) bridges are vulnerable to corrosion and fracture of tendons, and in particular, structures using the internal post-tensioned with grouted system have difficulties in maintenance due to limitations of inspection. In this study, the actual behavior of PSC I girder bridge was analyzed according to tendon damage. The target PSC I girder bridge, an decommissioned highway bridge of upper and lower bridges, had the service period of 33 years and 20 years, respectively. Deflection and concrete strain were measured according to the location of damaged tendon and loading method. Regardless of the age of the bridge, its structural performance decreased when the damaged tendon was closer to the center of the girder. The change in behavior increased as the truck load approached to the girder where the tendon cut. If the load was applied to the adjacent girder where the tendon was cut, the structural performance was likely to be maintained due to the influence of the entire structural system. The change in deflection was difficult to observe visually, while the concrete strain exceeded the cracking strain. Therefore, it is recommended that future monitoring and inspection of PSC I girder bridges should focus on concrete strain or cracking.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.454-458
• /
• 2005

여름철 집중강우시 유입되는 고탁수층은 저수지의 밀도성층으로 인하여 표수층 하부에 위치하며, 이를 적기에 배제하지 않을 경우에는 수평방향의 확산현상과 연직방향의 전도현상으로 인해 저수지 전역에 분포하게 되어, 탁수현상의 장기화를 유발한다. 일본 사메우라댐의 경우에는 1977년 9월 태풍 17호에 의한 집중호우로 대량의 고탁수가 유입되어 하류하천으로의 댐 방류수의 고탁도현상이 장기간 지속된 바 있다. 이와 같은 탁수장기화에 대한 저수지내 대책의 하나로서 홍수유입후 탁도가 높은 물을 단기간동안 방류하고, 갈수기에는 탁도가 낮은 물을 방류하는 선택취수 개념이 제안된 바 있다. 국내의 임하댐의 경우에도 2002년 태풍 '루사'와 2003년 태풍 '매미'로 인해 발생한 탁수가 전도현상을 거치며 저수지내 전수층에 확산됨으로써 댐방류수의 고탁도현상이 장기화된바 있다. 이로 인하여 댐하류에 위치한 안동시 용상정수장의 동절기 정수처리 장애로 2003년 11월이후 약 160여일동안 댐방류가 중단된 바 있다. 임하댐의 경우에도 탁수장기화에 대한 대책으로서 홍수기 고탁수층을 우선배제한 후, 저수지내에 유입되는 청수을 담수함으로써 이를 방지할 수 있다. 이러한 선택취수 기법은 동일한 수리동역학적 개념을 적용하여 하류하천의 냉해문제를 대비하기 위한 방법으로 표층의 온수를 선택방류하는 데에도 이용될 수 있다. 이와 같은 선택취수를 효율적으로 수행하기 위해서는 취수시설에 접근하는 밀도흐름을 정확하게 이해하고 있어야 한다. 또한 취수탑 인근에서의 온도 및 탁도 등의 연직분포를 실시간으로 파악할 수 있는 자동수질측정시스템이 구축되어 있어야 한다. 현재 임하댐의 경우, 하류하천의 수질을 고려한 효율적인 탁수배제를 위하여 상류 유입부 2개소, 발전취수탑 전면 1개소, 조정지댐 1개소 등 총 4개의 자동수질측정시스템이 설치되어 탁도와 온도가 실시간으로 모니터링되고 있으며, 향후 강우시 저수지에서의 밀도흐름을 보다 정밀하게 모니터링하기 위하여 저수지내 4개의 주요지점에 추가적으로 설치될 예정이다. 이와 같은 자동측정시스템과 더불어 주기적인 세부 수질조사를 실시하면 저수지내의 온도성층 변화와 탁수층 분포를 매우 정확하게 파악할 수 있으며, 호소의 수질모형과 연계하여 강우시 탁수 도달시간과 탁수량을 사전에 예측할 수도 있다. 또한 이와 같은 기초적인 정보를 바탕으로 하류하천의 탁수 피해를 최소화할 수 있는 선택취수탑의 운영방안을 수립할 수 있다 본 연구에서는 이를 위해 선택취수탑 주위의 성층흐름을 기존의 실험자료와 수치해석을 통하여 분석하였고, 온도성층구조나 취수구의 위치변화에 따른 방류수 수질특성을 조사하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.605-609
• /
• 2006

In this study, two kinds of smart accelerometers are investigated for the application of smart sensors to the structural health monitoring of infrastructures. Smart optical Fiber Bragg Grating (FBG) type and Micro-Electo-Mechanical System (MEMS) type accelerometers are selected for this study and the high sensitive ICP type accelerometer is used for the reference sensor. Small size shaking table tests were performed with 3-story shear building model using random input ground motions. The output only modal identification was carried out using stochastic subspace identification and the performances of sensors are compared in modal domain indirectly. The modal sensitivity method was applied to update the story stiffness of numerical model and the updated results were verified using the additional experiments for the same structure with additional mass.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.4
• /
• pp.503-514
• /
• 2006

FBG sensors are capable of measuring the strain of structures easily and more durably than electric resistance gauges. Thus, many researches are dedicated to the application for the response monitoring or non-destructive evaluation of structures using FBG sensors. Additionally, the measured strains at the top and bottom of a cross-section can be transformed into the curvature of the section, which can be used to calculate its vertical displacement. Hence, this study aims to measure the dynamic strain signals of a steel section simply supported beam and to estimate the dynamic displacement from the strain signals, after which the estimated displacement is com pared with the measured displacement. The dynamic characteristics (natural frequency, damping ratio and mode shape) of the beam are predicted from both the estimated and measured displacement signals, and from the strain time history of the FBG sensors. The predicted properties are compared with those of an analytical model of the beam. The estimated displacement. However, the predicted dynamic properties from both the estimated displacements and the measured strains are well-correlated with those from the measured displacement. It is therefore appreciated that the estimation of the dynamic properties of FBG sensor signals is reasonable. Especially, the strain signal of the FBG sensor was amplified at a higher-frequency region in comparison with the displacement estimation with higher-mode properties.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.3
• /
• pp.311-322
• /
• 2022

This study performed 4-point flexural tests of reinforced concrete to which was attached a distributed optical fiber sheet and carbon fiber reinforced polymer (CFRP) sheets in order to assess the effect of the CFRP sheets and the applicability of a BOTDR sensor simultaneously. To evaluate the reinforcing effect, various degrees of CFRP sheet attachment were manufactured, and to evaluate the sensing ability, strains obtained from a BOTDR sensor were compared with strains measured from electric resistance strain gauges that were attached to the concrete surface. From the results, the reinforcing effects were evidently different according to the attachment type of the CFRP sheets, and it was confirmed that the main influencing factor on the reinforcing effect was the type of attachment rather than the attachment area. The reinforced concrete structural behavior was visualized with strains measured from the BOTDR sensor as load increased, and it was identified that load was concentrated in the CFRP reinforced area. Strains from the BOTDR sensor were similar to those from the electric resistance strain gauge; thereby a BOTDR sensor can be effective in the analysis of structural behaviorsof massive infrastructure. Finally, the strain from a BOTDR sensor was high where CFRP sheet fall-off occurs, and it would therefore be efficient to track local damage locations of CFRP sheets by utilizing a BOTDR sensor.