• Journal of Biosystems Engineering
• /
• v.6 no.2
• /
• pp.9-19
• /
• 1982

The aim of this study was to improve the startability of the diesel engine at low temperature. The specific objective was to determine the optimum type of precombustion chamber. The eight different types of precombustion chamber and two different types of the cylinder head were designed and tested by $2^7$ factorial experiments with four replications. The lowest starting temperature for first operation, the maximum output, and the specific fuel consumption at full load and overload were checked and analyzed. The results of the study are summarized as follows; 1. The lowest starting temperature was lowered as much as $2.4^{\circ}C$ and the maximum output was increased as much as 0.3 ps with respect to the difference in the relative angle of the main passageway against the piston head from 20 degree to 18 degree. 2. The lowest starting temperature and the maximum out-put were lowered as much as $3.3^{\circ}C$ and 0.3 ps respectively with respect to the difference in the angle of the cylinder head groove from 20 degree to 18 degree. 3. The lowest starting temperature and the maximum out put were lowered as much as $2^{\circ}C$ and 0.2 ps respectively with respect to the difference in the length of the precombustion chamber from 17.5 mm to 15.5mm. 4. There was no significant difference in the startability but the maximum output was increased as much as 0.2 ps with respect to the difference in the diameter of the main passageway from 4.8mm to 4.5mm. 5. The lowest starting temperature was obtained under the condition at 47 degree in the angle of the main passageway and at 18 degree in the angle of the cylinder head groove. The maximum output and the minimum specific fuel consumption was obtained under the condition at 4.5mm in the diameter of the main passageway and at 17.5mm in the length of the precombustion chamber. 6. The angle of the cylinder head groove and the main passageway appeared to the major factors affecting the startability significantly. The interaction between the diameter of the main pass ageway and the length of the precombustion chamber had an significant influence on the maximum output. So it would be recommended to study further on the interaction between two factors mentioned above by expanding their levels. 7. The optimum condition suggested by this study could lower the starting temperature by $6^{\circ}C$ compared to the conventional precombustion chambers.

• Korean Journal of Soil Science and Fertilizer
• /
• v.46 no.1
• /
• pp.53-57
• /
• 2013

A severe defoliation by typhoon in early autumn reduces fruit quality for the current season and reserve accumulations for the next season. This study was conducted to determine the effects of foliar applications during the autumn on alleviating the damages after defoliation. Leaves of 2-year-old 'Fuyu' trees, grown in 50-L pots under a rain-shelter, were 75%-defoliated on September 9. In mid-September and early October, trees were treated either with eight foliar applications of urea or with four alternating applications of urea and $KH_2PO_4$ (urea + KP application), all at 0.5% (w/v). Trees untreated after the defoliation served as the control. The urea applications slightly increased N and P concentrations of the leaves collected on November 6, while urea + KP applications significantly increased P and K concentrations. Foliar applications did not affect fruit growth, but tended to decrease skin coloration. Fruit soluble solids increased by 1.5 and $1.0^{\circ}Brix$ for urea and urea + KP applications, respectively. There was a significant increase in dry weight of fine root for the foliar application treatments but not in those of aerial woods and larger roots. With the foliar applications, N concentration tended to increase in the permanent organs but not P and K, whereas soluble sugars and starch notably increased in shoot, trunk, or fine root regardless of the different applications. Results indicated that the foliar applications could partially help to restore fruit quality and carbohydrate accumulations in the defoliated trees.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.26 no.1
• /
• pp.110-114
• /
• 1981

These experiments were carried out to define the effects of NAA, 2, 4-D and Benzyladenine on the callus induction and the organ differentiation from the explants and to find out the vegetative propagation method of Korean ginseng. The results obtained are summarized as follows; 1. NAA was significantly effective in forming roots from the ginseng stem segment and the number of roots was increased by increasing NAA concentration in the medium. The roots were formed from both distal and proximal ends of the ginseng stem segments grown on the medium containing more than 2mg/L of NAA. 2. The amount of callus growth increased proportionatly with NAA concentration in the range of 4.0mg per liter in the medium. The callus was easly induced from stem segment than leaf segment and 2, 4-D was more effective in callus induction and growth than NAA. 3. The benzyladenine showed the significant inhibition effect in forming roots from ginseng explant. The callus was not induced with BA alone, but in BA and 2, 4-D or BA and NAA added medium, the callus was easily induced and its growth was also accelerated. The interaction effects between 2, 4-D and BA on the callus induction and growth were significantly higher than those between NAA and BA. 4. As the ginseng embryos were cultured on the M.S. medium supplemented with 2mg per liter NAA, number of shoots was significantly increased and the percentage of embryo which had shown more than 4 shoots later was 22.2%. On the medium containing 8mg per liter NAA, the ginseng embryo showed the normal growth of shoots and leaves, but increased roots and callus induction on the basal part of shoots. 5. When the shoots with 3 leaflets were cut in 1.5cm long and grown on the Blayde's medium containing NAA 1.0mg per liter, roots were formed at the proximal end of shoot, and a new ginseng seedling was successfully obtained.

• Korean Journal of Heritage: History & Science
• /
• v.52 no.3
• /
• pp.74-93
• /
• 2019

The Bird Track Site in the Haman Formation in Yongsanri (Natural Monument No. 222) was reported on the named Koreanaornis hamanensis and Jindongornipes kimi sauropod footprint Brontopodus and ichnospecies Ochlichnus formed by Nematoda. This site has outstanding academic value because it is where the second-highest number of bird tracks have been reported in the world. However, only 25% of the site remains after being designated a natural monument in 1969. This is due to artificial damage caused by worldwide fame and quarrying for flat stone used in Korean floor heating systems. The Haman Formation, including this fossil site, has lithofacies showing reddish-grey siltstone and black shale, alternately. The boundary of the two rocks is progressive, and sedimentary structures like ripple marks and sun cracks can clearly be found. This site was divided into seven formations according to sedimentary sequences and structures. The results of a nondestructive deterioration evaluation showed that chemical and biological damage rates were very low for all formations. Also, physical damage displayed low rates with 0.49% on exfoliation, 0.04% on blistering, 0.28% on break-out; however, the joint crack index was high, 6.20. Additionally, efflorescence was observed on outcrops at the backside and the northwestern side. Physical properties measured by an indirect ultrasonic analysis were found to be moderately weathered (MW). Above all, the southeastern side was much fresher, though some areas around the column of protection facility appeared more weathered. Furthermore, five kinds of discontinuity surface can be found at this site, with the bedding plane showing the higher share. There is the possibility of toppling failure occurring at this site but stable on plane and wedge failure by means of stereographic projection. We concluded that the overall level of deterioration and stability were relatively fine. However, continuous monitoring and conservation treatment and management should be performed as situations such as the physicochemical weathering of the fossil layer, and the efflorescence of the mortar adjoining the protection facility's column appear to be challenging to control.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.4
• /
• pp.78-99
• /
• 2020

The Buddha triad and 16 Arhat statues carved on the rock surface at Seongbulsa temple is the only domestic remaining example of all 16 Arhats, so its academic value is very high. However, it is severely damaged and so required a stability evaluation through study of digital documentation and precise diagnosis for the purpose of comprehensive conservation. This process established that the Buddha statues were of similar scale, while the Arhats showed a wide variety of sizes, and the two kith and kin in the volume were larger than the Arhats. It was estimated that the statues of food for Buddha are similar to the Arhat statues, and most of the statues are well-formed. The rock used to carve the Buddha statues is banded gneiss with distinct foliation, alternating between white bands of quartz and feldspar and black bands composed of biotite. The Buddha statues have been damaged by physical weathering, discoloration, and biological contamination. In damage evaluations, joint (3.6 crack index), peeling (5.2%), exfoliation (1.7%), and falling off (0.1%) were observed on the rock surface of the Buddha statues. In particular, due to severe biological weathering, stage 9 and 10 biological coverage of the rock surface accounted for 57.5% of the total area, and stages 5 to 8 also accounted for a high share at 22.3%. The discoloration factors were shown to be dark brown and white with Fe, Ca, and S, and a large amount of C detected in the blackened contaminants, and the damage weight high in all areas. Discontinuities in different directions were identified in the rock surface. Analysis of potential rock failure types indicated that there is a possibility of plane and toppling failure, but wedge failure is unlikely to occur. The mean ultrasonic velocity of the main rock surface was 2,463m/sec, the lower part of the left side with a large number of joints was relatively low, and the highly weathered (HW) type to the completely weathered (CW) type concentrated distribution, showing weak properties. For the Buddha statues, conservation treatment is required for about 14.9% of micro cracks and 58.9% of exfoliation cracks. In addition, in order to improve the conservation environment of the Buddha statues, maintenance of drainage and ground preparations for the rock surface gradient and plants are necessary, and protection facilities should be reviewed for long-term conservation and management purposes.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.6
• /
• pp.642-652
• /
• 2008

The aim of our research was to apply experimental design methodology in the optimization condition of Photo-Fenton oxidation of the residual livestock wastewater after the coagulation process. The reactions of Photo-Fenton oxidation were mathematically described as a function of parameters amount of Fe(II)($x_1$), $H_2O_2(x_2)$ and pH($x_3$) being modeled by the use of the Box-Behnken method, which was used for fitting 2nd order response surface models and was alternative to central composite designs. The application of RSM using the Box-Behnken method yielded the following regression equation, which is an empirical relationship between the removal(%) of livestock wastewater and test variables in coded unit: Y = 79.3 + 15.61x$_1$ - 7.31x$_2$ - 4.26x$_3$ - 18x$_1{^2}$ - 10x$_2{^2}$ - 11.9x$_3{^2}$ + 2.49x$_1$x$_2$ - 4.4x$_2$x$_3$ - 1.65x$_1$x$_3$. The model predicted also agreed with the experimentally observed result(R$^2$ = 0.96) The results show that the response of treatment removal(%) in Photo-Fenton oxidation of livestock wastewater were significantly affected by the synergistic effect of linear terms(Fe(II)($x_1$), $H_2O_2(x_2)$, pH(x$_3$)), whereas Fe(II) $\times$ Fe(II)(x$_1{^2}$), $H_2O_2$ $\times$ $H_2O_2$(x$_2{^2}$) and pH $\times$ pH(x$_3{^2}$) on the quadratic terms were significantly affected by the antagonistic effect. $H_2O_2$ $\times$ pH(x$_2$x$_3$) had also a antagonistic effect in the cross-product term. The estimated ridge of the expected maximum response and optimal conditions for Y using canonical analysis were 84 $\pm$ 0.95% and (Fe(II)(X$_1$) = 0.0146 mM, $H_2O_2$(X$_2$) = 0.0867 mM and pH(X$_3$) = 4.704, respectively. The optimal ratio of Fe/H$_2O_2$ was also 0.17 at the pH 4.7.